• There are no items in your cart

API 677 :2006

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

GENERAL-PURPOSE GEAR UNITS FOR PETROLEUM, CHEMICAL AND GAS INDUSTRY SERVICES
Available format(s)

Hardcopy , PDF

Superseded date

02-20-2021

Language(s)

English

Published date

01-01-2016

1 GENERAL
2 BASIC DESIGN
3 ACCESSORIES
4 INSPECTION, TESTING, AND PREPARATION FOR SHIPMENT
5 VENDOR'S DATA
APPENDIX A - GENERAL-PURPOSE GEAR DATA SHEETS
APPENDIX B - LATERAL CRITICAL SPEED MAP AND MODE
             SHAPES FOR A TYPICAL ROTOR
APPENDIX C - TYPICAL LUBE-OIL SYSTEMS
APPENDIX D - MATERIAL SPECIFICATIONS FOR
             GENERAL-PURPOSE GEAR UNITS PAGE
APPENDIX E - VENDOR DRAWING AND DATA REQUIREMENTS
APPENDIX F - REFERENCED SPECIFICATIONS
APPENDIX G - SPIRAL BEVEL GEAR-TOOTH CONTACT
             ARRANGEMENT REQUIREMENTS FOR INSPECTION
APPENDIX H - RESIDUAL UNBALANCE WORKSHEETS

Defines the minimum requirements for general-purpose, enclosed single and multistage gear units incorporating parallel shaft helical and right angle spiral bevel gears for the petroleum, chemical, and gas industries.

DocumentType
Standard
Pages
104
ProductNote
Reconfirmed 2006
PublisherName
American Petroleum Institute
Status
Superseded
SupersededBy
Supersedes

ASME PV CODE 8 DIV 2 : 2017 BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 2- ALTERNATIVE RULES
AGMA 9002 : B BORES AND KEYWAYS FOR FLEXIBLE COUPLINGS (INCH SERIES)
AGMA 6011 : I SPECIFICATION FOR HIGH SPEED HELICAL GEAR UNITS
ABMA 9 : 2015 LOAD RATINGS AND FATIGUE LIFE FOR BALL BEARINGS
ISO 7005-2:1988 Metallic flanges — Part 2: Cast iron flanges
ISO 3744:2010 Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane
ABMA 11 : 2014 LOAD RATINGS AND FATIGUE LIFE FOR ROLLER BEARINGS
ASME PV CODE 9 : 2017 BOILER AND PRESSURE VESSEL CODE - WELDING, BRAZING, AND FUSING QUALIFICATIONS - QUALIFICATION STANDARD FOR WELDING, BRAZING, AND FUSING PROCEDURES; WELDERS; BRAZERS; AND WELDING, BRAZING, AND FUSING OPERATORS
AGMA 6025 : D SOUND FOR ENCLOSED HELICAL, HERRINGBONE AND SPIRAL BEVEL GEAR DRIVES
NEMA SM 23-1991 (R1997, R2002) STEAM TURBINES FOR MECHANICAL DRIVE SERVICE
AGMA 2101 : D FUNDAMENTAL RATING FACTORS AND CALCULATION METHODS FOR INVOLUTE SPUR AND HELICAL GEAR TEETH (METRIC EDITION)
ASME PV CODE 8 DIV 1 : 2017 BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 1
ISO 1328-1:2013 Cylindrical gears — ISO system of flank tolerance classification — Part 1: Definitions and allowable values of deviations relevant to flanks of gear teeth
ISO 724:1993 ISO general-purpose metric screw threads — Basic dimensions
API 614 : 2008 LUBRICATION, SHAFT-SEALING AND OIL-CONTROL SYSTEMS AND AUXILIARIES
AGMA 6010 : F STANDARD FOR SPUR, HELICAL, HERRINGBONE AND BEVEL ENCLOSED DRIVES
NEMA 250 : 2014 ENCLOSURES FOR ELECTRICAL EQUIPMENT (1000 VOLTS MAXIMUM)
ASME B16.42 : 2016 DUCTILE IRON PIPE FLANGES AND FLANGED FITTINGS - CLASSES 150 AND 300
ASME B31.3:2016 PROCESS PIPING
ASME PV CODE 8 DIV 3 : 2017 BPVC Section VIII-BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS - ALTERNATIVE RULES FOR CONSTRUCTION OF HIGH PRESSURE VESSELS
AGMA 6001 : D DESIGN AND SELECTION OF COMPONENTS FOR ENCLOSED GEAR DRIVES
ISO 6708:1995 Pipework components Definition and selection of DN (nominal size)
ISO 281:2007 Rolling bearings Dynamic load ratings and rating life
ISO 6336-5:2016 Calculation of load capacity of spur and helical gears Part 5: Strength and quality of materials
ISO 262:1998 ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts
ASME B1.20.1 : 2013(R2018) PIPE THREADS, GENERAL PURPOSE (INCH)
API 670 : 2014 MACHINERY PROTECTION SYSTEMS
ISO 7-1:1994 Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation
AGMA 908 : B GEOMETRY FACTORS FOR DETERMINING THE PITTING RESISTANCE AND BENDING STRENGTH OF SPUR, HELICAL AND HERRINGBONE GEAR TEETH
NFPA 70 : 2017 NATIONAL ELECTRICAL CODE
IEC 60079-0:2011 Explosive atmospheres - Part 0: Equipment - General requirements
EN 1563:2011 Founding - Spheroidal graphite cast irons
ASME B16.5 : 2017 PIPE FLANGES AND FLANGED FITTINGS: NPS 1/2 THROUGH NPS 24 METRIC/INCH STANDARD
ISO 261:1998 ISO general purpose metric screw threads General plan
ISO 5753:1991 Rolling bearings — Radial internal clearance
API 686 : 2009 RECOMMENDED PRACTICE FOR MACHINERY INSTALLATION AND INSTALLATION DESIGN
ABMA 20 : 2011 RADIAL BEARINGS OF BALL, CYLINDRICAL ROLLER AND SPHERICAL ROLLER TYPES - METRIC DESIGN
EN 10084:2008 Case hardening steels - Technical delivery conditions
ISO 7005-1:2011 Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems
ASTM E 709 : 2015 : REDLINE Standard Guide for Magnetic Particle Testing
ISO 3448:1992 Industrial liquid lubricants — ISO viscosity classification
ISO/TR 10064-1:2017 Code of inspection practice Part 1: Measurement of cylindrical gear tooth flanks
ABMA 7 : 1995 SHAFT AND HOUSING FITS FOR METRIC RADIAL BALL AND ROLLER BEARINGS (EXCEPT TAPERED ROLLER BEARINGS) CONFORMING TO BASIC BOUNDARY PLAN
EN 1561:2011 Founding - Grey cast irons
ISO/R 286:1962 ISO system of limits and fits Part I : General, tolerances and deviations

View more information
US$192.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.