API SPEC 17E : 2017

Superseded

Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Add to Watchlist

View superseded by

This Standard has been added successfully to your Watchlist.
Please visit My Watchlist to see all standards that you are watching.

Please log in or create an account to add this standard to your Watchlist.

We could not add this standard to your Watchlist.
Please retry or contact support for assistance.

You have already added this standard to your Watchlist.
Visit My Watchlist to view the full list.

SPECIFICATION FOR SUBSEA UMBILICALS

Available format(s): Hardcopy, PDF

Superseded date: 06-24-2021

Language(s):

Published date: 07-01-2017

Publisher: American Petroleum Institute

Add to Watchlist

Table of Contents - (Show below) - (Hide below)

1 Scope
2 Normative References
3 Terms, Abbreviated Terms, and Definitions
4 Functional Requirements
5 Safety, Design and Testing Philosophy
6 Design Requirements
7 Component Design, Manufacture, and Test
8 Terminations and Ancillary Equipment Design
9 Umbilical Design
10 Umbilical Manufacture and Test
11 Factory Acceptance Tests
12 Storage
13 Pre-installation Activity
14 Load-out
15 Installation Operations
Bibliography
Annex A (informative) - This annex intentionally
        left blank
Annex B (informative) - Information Provided in a Purchaser's
        Functional Specification
Annex C (informative) - Load-effect Analysis
Annex D (informative) - Umbilical Testing
Annex E (normative) - Fatigue Testing
Annex F (informative) - Hose and Tube Preferred Sizes
Annex G (normative) - Characterization Tests for Hoses and
        Umbilicals, Including Hoses
Annex H (normative) - Buckling of Metallic Tubes
Annex I (informative) - Tube Material Matrix
Annex J (informative) - Umbilical Full-scale Tests
Bibliography

Abstract - (Show below) - (Hide below)

Describes requirements and gives recommendations for the design, material selection, manufacture, design verification, testing, installation, and operation of umbilicals and associated ancillary equipment for the petroleum and natural gas industries.

General Product Information - (Show below) - (Hide below)

Document Type	Standard
ISBN
Pages
Product Note	This product is unavailable in Cuba, Iran, North Korea, Syria NEW CHILD ADD ENDUM1 IS NOW ADDED
Published
Publisher	American Petroleum Institute
Status	Superseded
Superseded By	API 17E:2017+ADDENDUM 1:2017
Supersedes	API 17E : 2010

Standards Referenced By This Book - (Show below) - (Hide below)

API RP 17B : 2014	RECOMMENDED PRACTICE FOR FLEXIBLE PIPE
API TR 17TR5 : 2012	AVOIDANCE OF BLOCKAGES IN SUBSEA PRODUCTION CONTROL AND CHEMICAL INJECTION SYSTEMS
EEMUA 194 : 2012	GUIDELINES FOR MATERIALS SELECTION AND CORROSION CONTROL FOR SUBSEA OIL AND GAS PRODUCTION EQUIPMENT
11/30253360 DC : 0	BS EN ISO 13628-14 - PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 14: SUBSEA HIGH INTEGRITY PRESSURE PROTECTION SYSTEMS (HIPPS)
API 2T REDLINE : 2010	PLANNING, DESIGNING, AND CONSTRUCTING TENSION LEG PLATFORMS
API RP 17W : 2014	RECOMMENDED PRACTICE FOR SUBSEA CAPPING STACKS
API TR 1PER15K-1 : 2013	PROTOCOL FOR VERIFICATION AND VALIDATION OF HIGH-PRESSURE HIGH-TEMPERATURE EQUIPMENT
API 2T : 2010 : R2015	PLANNING, DESIGNING, AND CONSTRUCTING TENSION LEG PLATFORMS
API 17E REDLINE : 2010	SPECIFICATION FOR SUBSEA UMBILICALS
API TR 17TR10 : 2015	SUBSEA UMBILICAL TERMINATION (SUT) DESIGN RECOMMENDATIONS
UNI EN ISO 13628-5 : 2010	PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 5: SUBSEA UMBILICALS
ABS 0195 : 2015 COR 2018	GUIDE FOR BUILDING AND CLASSING FLOATING OFFSHORE WIND TURBINE INSTALLATIONS
BS ISO 13628-5:2002	Petroleum and natural gas industries. Design and operation of subsea production systems Subsea umbilicals
API 17V : 2015	RECOMMENDED PRACTICE FOR ANALYSIS, DESIGN, INSTALLATION, AND TESTING OF SAFETY SYSTEMS FOR SUBSEA APPLICATIONS
04/302050 DC : DRAFT JAN 2004	ISO 13628-6 - PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 6: SUBSEA PRODUCTION CONTROL SYSTEMS
API TR 17TR2 : 2003	THE AGEING OF PA-11 IN FLEXIBLE PIPES
API 17F REDLINE : 2006	SPECIFICATION FOR SUBSEA PRODUCTION CONTROL SYSTEMS
API 17O : 2014	SUBSEA HIGH INTEGRITY PRESSURE PROTECTION SYSTEMS (HIPPS)
API STD 17F : 2017	SUBSEA PRODUCTION CONTROL SYSTEMS
ISO 13628-5:2009	Petroleum and natural gas industries Design and operation of subsea production systems Part 5: Subsea umbilicals
ISO 13628-6:2006	Petroleum and natural gas industries Design and operation of subsea production systems Part 6: Subsea production control systems
BS EN ISO 13628-6:2006 (published 2006-05)	Petroleum and natural gas industries. Design and operation of subsea production systems Subsea production control systems
EN ISO 13628-5:2009	Petroleum and natural gas industries - Design and operation of subsea production systems - Part 5: Subsea umbilicals (ISO 13628-5:2009)
EN ISO 13628-6:2006	Petroleum and natural gas industries - Design and operation of subsea production systems - Part 6: Subsea production control systems (ISO 13628-6:2006)
I.S. EN ISO 13628-5:2009	PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 5: SUBSEA UMBILICALS
12/30250727 DC : 0	BS EN ISO 13628-6 - PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 6: SUBSEA PRODUCTION CONTROL SYSTEMS
BS EN ISO 13628-5:2009 (published 2010-01)	Petroleum and natural gas industries. Design and operation of subsea production systems Subsea umbilicals
API SPEC 17J : 2014	SPECIFICATION FOR UNBONDED FLEXIBLE PIPE
API RP 2T : 2010	PLANNING, DESIGNING, AND CONSTRUCTING TENSION LEG PLATFORMS
API TR 17TR9 : 2017	UMBILICAL TERMINATION ASSEMBLY (UTA) SELECTION AND SIZING RECOMMENDATIONS
API 14FZ : 2013	RECOMMENDED PRACTICE FOR DESIGN, INSTALLATION, AND MAINTENANCE OF ELECTRICAL SYSTEMS FOR FIXED AND FLOATING OFFSHORE PETROLEUM FACILITIES FOR UNCLASSIFIED AND CLASS 1, ZONE 0, ZONE 1, AND ZONE 2 LOCATIONS

Standards Referencing This Book - (Show below) - (Hide below)

ASTM E 1001 : 2016 : REDLINE	Standard Practice for Detection and Evaluation of Discontinuities by the Immersed Pulse-Echo Ultrasonic Method Using Longitudinal Waves
IEC 60038:2009	IEC standard voltages
NEMA WC 74 : 2012	5-46 KV SHIELDED POWER CABLE FOR USE IN THE TRANSMISSION AND DISTRIBUTION OF ELECTRIC ENERGY
IEC 60793-1-1 : 2017	OPTICAL FIBRES - PART 1-1: MEASUREMENT METHODS AND TEST PROCEDURES - GENERAL AND GUIDANCE
IEC 60228:2004	Conductors of insulated cables
EN 10257-2:2011	Zinc or zinc alloy coated non-alloy steel wire for armouring either power cables or telecommunication cables - Part 2: Submarine cables
API 17L2 : 2013	RECOMMENDED PRACTICE FOR FLEXIBLE PIPE ANCILLARY EQUIPMENT
ASTM E 309 : 2016 : REDLINE	Standard Practice for Eddy Current Examination of Steel Tubular Products Using Magnetic Saturation
IEC 60502-2:2014 RLV	Power cables with extruded insulation and their accessories for rated voltages from 1 kV (U_m = 1,2 kV) up to 30 kV (U_m = 36 kV) – Part 2: Cables for rated voltages from 6 kV (U_m = 7,2 kV) up to 30 kV (U_m = 36 kV)
ASME PV CODE 9 : 2017	BOILER AND PRESSURE VESSEL CODE - WELDING, BRAZING, AND FUSING QUALIFICATIONS - QUALIFICATION STANDARD FOR WELDING, BRAZING, AND FUSING PROCEDURES; WELDERS; BRAZERS; AND WELDING, BRAZING, AND FUSING OPERATORS
API 17F : 2014	SUBSEA PRODUCTION CONTROL SYSTEMS
ISO 9712:2012	Non-destructive testing Qualification and certification of NDT personnel
ICEA S 93 639 : 2012	5-46 KV SHIELDED POWER CABLE FOR USE IN THE TRANSMISSION AND DISTRIBUTION OF ELECTRIC ENERGY
NEMA WC 70 : 2009	POWER CABLES RATED 2000 VOLTS OR LESS FOR THE DISTRIBUTION OF ELECTRICAL ENERGY
ISO 6801:1983	Rubber or plastics hoses Determination of volumetric expansion
IEC 60793-2:2015	Optical fibres - Part 2: Product specifications - General
ASTM E 562 : 2011 : REDLINE	Standard Test Method for Determining Volume Fraction by Systematic Manual Point Count
ISO 14732:2013	Welding personnel Qualification testing of welding operators and weld setters for mechanized and automatic welding of metallic materials
IEC 60502-1:2004+AMD1:2009 CSV	Power cables with extruded insulation and their accessories for rated voltages from 1 kV (U_m = 1,2 kV) up to 30 kV(U_m = 36 kV) - Part 1: Cables for rated voltages of 1 kV (U_m = 1,2 kV) and 3 kV (U_m = 3,6 kV)
NEMA WC 53 : 2016	STANDARD TEST METHODS FOR EXTRUDED DIELECTRIC POWER, CONTROL, INSTRUMENTATION, AND PORTABLE CABLES FOR TEST
ASTM E 384 : 2017 : REDLINE	Standard Test Method for Microindentation Hardness of Materials
ASTM E 273 : 2015 : REDLINE	Standard Practice for Ultrasonic Testing of the Weld Zone of Welded Pipe and Tubing
ASME B31.3:2016	PROCESS PIPING
API SPEC 17J : 2014	SPECIFICATION FOR UNBONDED FLEXIBLE PIPE
API 2RD : 2013	DYNAMIC RISERS FOR FLOATING PRODUCTION SYSTEMS
API 17L1 : 2013	SPECIFICATION FOR FLEXIBLE PIPE ANCILLARY EQUIPMENT
ISO 10619-2:2011	Rubber and plastics hoses and tubing Measurement of flexibility and stiffness Part 2: Bending tests at sub-ambient temperatures
ICEA S 94 649 : 2013	CONCENTRIC NEUTRAL CABLES RATED 5 THROUGH 46 KV
ASTM E 426 : 2016 : REDLINE	Standard Practice for Electromagnetic (Eddy Current) Examination of Seamless and Welded Tubular Products, Titanium, Austenitic Stainless Steel and Similar Alloys
ISO 8308:2015	Rubber and plastics hoses and tubing Determination of transmission of liquids through hose and tubing walls
ICEA T 27 581 : 2016	STANDARD TEST METHODS FOR EXTRUDED DIELECTRIC POWER, CONTROL, INSTRUMENTATION, AND PORTABLE CABLES FOR TEST
IEC 62230:2006+AMD1:2013 CSV	Electric cables - Spark-test method
EN 10204:2004	Metallic products - Types of inspection documents
API RP 17B : 2014	RECOMMENDED PRACTICE FOR FLEXIBLE PIPE
ASME PV CODE 5 : 2017	BOILER AND PRESSURE VESSEL CODE - NONDESTRUCTIVE EXAMINATION
ISO 7751:2016	Rubber and plastics hoses and hose assemblies Ratios of proof and burst pressure to maximum working pressure
ICEA S 97 682 : 2013	UTILITY SHIELDED POWER CABLES RATED 5 THROUGH 46 KV
ISO 1402:2009	Rubber and plastics hoses and hose assemblies Hydrostatic testing
ISO 4080:2009	Rubber and plastics hoses and hose assemblies Determination of permeability to gas
ISO 6803:2017	Rubber or plastics hoses and hose assemblies — Hydraulic-pressure impulse test without flexing
ISO 15607:2003	Specification and qualification of welding procedures for metallic materials General rules
IEEE 400-2012	GUIDE FOR FIELD TESTING AND EVALUATION OF THE INSULATION OF SHIELDED POWER CABLES SYSTEMS RATED 5 KV AND ABOVE
API RP 17I : 1996	INSTALLATION GUIDELINES FOR SUBSEA UMBILICALS
ICEA T 24 380 : 2013	PARTIAL DISCHARGE TEST PROCEDURE
API 17H : 2013	REMOTELY OPERATED TOOLS AND INTERFACES ON SUBSEA PRODUCTION SYSTEMS
ASTM E 8/E8M : 2016-09	TEST METHODS FOR TENSION TESTING OF METALLIC MATERIALS
IEC 60794-1-21:2015	Optical fibre cables - Part 1-21: Generic specification - Basic optical cable test procedures - Mechanical tests methods
ASTM E 92 : 2017 : REDLINE	Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials

Categories associated with this Standard - (Show below) - (Hide below)

Sub-Categories associated with this Standard - (Show below) - (Hide below)

Add To Cart

Product Format

Quantity

Buy now

Add to cart

Create account