AS 1646.3-2000

1 - AS 1646.3-2000 ELASTOMERIC SEALS FOR WATERWORKS PURPOSES - MATERIAL REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND....
4 - PREFACE
5 - CONTENTS
6 - SECTION 1 SCOPE AND GENERAL
6 - 1.1 SCOPE
6 - 1.2 REFERENCED DOCUMENTS
7 - 1.3 DEFINITIONS
7 - 1.4 CLASSIFICATION
9 - SECTION 2 REQUIREMENTS
9 - 2.1 MATERIALS
9 - 2.1.1 General
9 - 2.1.2 Effect on water quality
9 - 2.2 FINISHED SEAL REQUIREMENTS
9 - 2.2.1 Dimensional tolerances
9 - 2.2.2 Imperfections and defects
9 - 2.2.3 Hardness
9 - 2.2.4 Tensile strength and elongation at break
9 - 2.2.5 Compression set in air
10 - 2.2.6 Accelerated ageing in air
10 - 2.2.7 Stress relaxation in compression
10 - 2.2.8 Volume change in water
10 - 2.2.9 Ozone resistance
10 - 2.2.10 Tear strength for joint seals for hot water supply
10 - 2.2.11 Compression set in water for joint seals for hot water supply
10 - 2.2.12 Splices of prevulcanized profile ends and joints
10 - 2.3 OPTIONAL REQUIREMENTS FOR JOINT SEALS FOR COLD WATER SUPPLY, DRAINAGE AND SEWERAGE
10 - 2.3.1 General
10 - 2.3.2 Low temperature performance at -25°C
11 - 2.3.3 Volume change in oil
11 - 2.4 PURCHASING
13 - SECTION 3 TEST PIECES AND TEMPERATURE
13 - 3.1 PREPARATION OF TEST PIECES
13 - 3.2 TEST TEMPERATURE
14 - SECTION 4 DESIGNATION
15 - SECTION 5 MARKING AND STORAGE
15 - 5.1 MARKING
15 - 5.2 STORAGE
16 - APPENDIX A - MEANS FOR DEMONSTRATING COMPLIANCE WITH THIS STANDARD
16 - A1 SCOPE
16 - A2 RELEVANCE
16 - A3 PRODUCT CERTIFICATION
16 - A4 TESTING
16 - A4.1 General
16 - A4.2 Sampling
17 - A4.3 Retesting
17 - A4.4 Rejection after retest
19 - APPENDIX B - DETERMINATION OF COMPRESSION SET IN HOT WATER AT 110°C
19 - B1 SCOPE
19 - B2 PRINCIPLE
19 - B3 APPARATUS
19 - B4 TEST PIECES
19 - B5 PROCEDURE

Specifies requirements for all elastomeric materils used in vulcanized seals with the exception of natural rubber and polyisoprene rubber for cold potable water supply (up to 50 degrees C), hot potable and non-potable water supply (up to 110 degrees C), drainage, sewerage and rainwater systems (continuous flow up to 45 degrees Celsius and intermittent flow up to 95 degrees C).

This Standard specifies requirements for synthetic elastomeric materials used in vulcanized seals with the exception of natural rubber and polyisoprene compounds for(a) cold potable water supply (up to 50C);(b) hot potable and non-potable water supply (up to 110C);(c) drainage, sewerage and rainwater systems (continuous flow up to 45C and intermittent flow up to 95C);The different designations of seals specified are defined according to their type, application and requirements (see Table 4.1).General requirements for finished joint seals are also given. Any additional requirements called for by the particular application are specified in the relevant product Standards taking into account that the performance of pipe joints is a function of the seal material properties, seal geometry and pipe joint design.This Standard should be used, where appropriate, with product Standards that specify performance requirements for joints.This Standard is applicable to joint seals for all pipeline materials, including iron, steel, clay, fibre cement, concrete, reinforced concrete, plastics and glass-reinforced plastics; and elastomeric components of composite or non-composite seals.In the case of composite seals for materials of hardness ranges from 76 IRHD to 96 IRHD, the requirements for elongation at break, compression set and stress relaxation apply only when the material is participating in the sealing function, or the long-term stability of the seal.Joint seals made with an enclosed void as part of their design are included in the scope of this Standard.Means for demonstrating compliance with this Standard are given in Appendix A.

First published as AS A139-1964.Second edition 1972.Revised and redesignated as AS 1646-1974.Second edition 1984.Third edition 1987.Fourth edition 1992.Revised and redesignated in part as AS 1646.3-2000. First published as AS A139-1964. Second edition 1972. Revised and redesignated as AS 1646-1974. Second edition 1984. Third edition 1987. Fourth edition 1992. Revised and redesignated in part as AS 1646.3-2000.