Customer Support: +1 416-401-8730

Login to i2i Subscription Intertek.com
  • There are no items in your cart
Please enter a keyword to search
Advanced search
Home
AS
AS 1774.4.1-1990

AS 1774.4.1-1990

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Refractories and refractory materials - Physical test methods Preparation of test pieces - Castable refractories

Available format(s)

Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users

Superseded date

06-30-2017

Language(s)

English

Published date

01-01-1990

Publisher

Standards Australia

1 - AS 1774.4.1-1990 REFRACTORIES AND REFRACTORY MATERIALS - PHYSICAL TEST METHODS - PREPARATION OF TEST PIECES - CASTABLE REFRA
1 - PREFACE
1 - CONTENTS
1 - METHOD
1 - 1 SCOPE.
2 - 2 REFERENCED DOCUMENTS.
2 - 3 DEFINITIONS.
2 - 3.1 Cast coverage
2 - 3.2 Dense castable
2 - 3.3 Medi umweight castable
2 - 3.4 Lightweight castable
2 - 3.5 Low- cement castable
2 - 4 PRINCIPLE.
2 - 5 APPARATUS.
2 - 5.1 Mixer
2 - 5.2 Vibrating table
2 - 5.3 Moulds
2 - 5.4 Clamps
2 - 5.5 Drying oven
2 - 5.6 Weighing scale
2 - 5.7 Riffler
2 - 5.8 Thermometer
2 - 5.9 Timing device.
3 - 6 SAMPLING.
3 - 7 PROCEDURE.
3 - 7.1 Sample division.
3 - 7.2 Mixing.
3 - 7.3 Casting of test pieces.
3 - 7.4 Curing and drying.
4 - 5 REPORT.
5 - APPENDIX A - METHOD FOR MEASURING CONSISTENCY OF UNSHAPED CASTABLE REFRACTORIES
5 - A1 SCOPE.
5 - A2 PRINCIPLE.
5 - A3 APPARATUS.
5 - A3.1 Balance
5 - A3.2 Riffler
5 - A3.3 Flow table and mould
5 - A3.4 Callipers
5 - A3.5 Tamper
5 - A3.6 Trowel
5 - A3.7 Castable mixer
5 - A3.8 Thermometer
5 - A4 PROCEDURE.
5 - A4.1 Sample size division.
5 - A4.2 Temperature measurement.
5 - A4.3 Preparation of castable sample.
6 - A4.4 Determination of flow.
6 - A5 REPORT.

Sets out a procedure for laboratory preparation of test pieces from castable refractory materials. A method for measuring consistency is included.

This Standard describes a procedure for laboratory preparation of test pieces from castable refractory materials.NOTE: The values obtained from test pieces prepared using this method may not correspond with those obtained from test pieces prepared using non-vibratory, or other vibratory, methods. This Standard applies to dense, mediumweight and lightweight castables containing either hydraulic cements or other binders. It does not apply to castable refractories intended primarily for gun application, or to low-cement castables.NOTE: Preparation of test pieces from low-cement castables is covered by AS 1774.4.2.A method for measuring the consistency of unshaped castable refractories is given in Appendix A.

Committee
MN-007
DocumentType
Standard
ISBN
0 7262 6114 9
Pages
6
PublisherName
Standards Australia
Status
Superseded
SupersededBy
Supersedes

Under Revision see DR 01328 CP

AS 2497.1-2001 Procedures for acceptance testing of refractory products Batch procedure (Reconfirmed 2013)
AS 1774.9-1992 Refractories and refractory materials - Physical test methods Determination of resistance to the disintegrating effect of carbon monoxide
AS 1774.11-1996 Refractories and refractory materials - Physical test methods Thermal expansion
AS 1774.13-2000 Refractories and refractory materials - Physical test methods Permanent dimensional change (Reconfirmed 2013)
AS 2780-1999 Refractories and refractory materials - Glossary of terms
AS 1774.9-2000
AS 1774.27-2001 Refractories and refractory materials - Physical test methods Modulus of rupture at elevated temperatures
AS 1774.1-1991 Refractories and refractory materials - Physical test methods Determination of cold compressive strength
AS 1774.4.2-1992 Refractories and refractory materials - Physical test methods Preparation of test pieces - Low-cement castable refractories
AS 1774.4.3-1998 Refractories and refractory materials - Physical test methods Preparation of test pieces - Unshaped refractories on site
AS 1774.1-2000 Refractories and refractory materials - Physical test methods Determination of cold compressive strength (Reconfirmed 2013)
AS 1774.27-1992 Refractories and refractory materials - Physical test methods Modulus of rupture at elevated temperatures

View more information
US$26.49
Excluding Tax where applicable
USD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF 1 User - English
PDF 3 Users - English
PDF 5 Users - English
PDF 9 Users - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us