• There are no items in your cart

AS 3007.3-2004

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Electrical installations - Surface mines and associated processing plant - General requirements for equipment and ancillaries
Available format(s)

Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users

Superseded date

06-30-2017

Published date

01-01-2004

Preview

1 - AS 3007.3-2004 ELECTRICAL INSTALLATIONS-SURFACE MINES AND ASSOCIATED PROCESSING PLANT - GENERAL REQUIREMENTS FOR...
4 - PREFACE
5 - CONTENTS
7 - SECTION 1 SCOPE AND REFERENCED DOCUMENTS
7 - 1.1 SCOPE
7 - 1.2 REFERENCED DOCUMENTS
9 - SECTION 2 GENERAL REQUIREMENTS FOR ELECTRICAL COMPONENTS
9 - 2.1 INTRODUCTION
9 - 2.2 DESIGN AND SELECTION
9 - 2.3 RELEVANT STANDARDS
9 - 2.4 MATERIALS
9 - 2.5 PROTECTION
10 - 2.6 OPERATING CONDITIONS
10 - 2.7 SITE CONDITIONS
10 - 2.8 COMBUSTIBLE MATERIALS
10 - 2.9 EARTH TERMINAL
10 - 2.10 NOISE LIMITATIONS
11 - SECTION 3 ROTATING MACHINES
11 - 3.1 MECHANICAL CONSTRUCTION
11 - 3.2 MECHANICAL PROTECTION
12 - SECTION 4 TRANSFORMERS
12 - 4.1 CORE, COIL AND TANK BRACING
12 - 4.2 ENCLOSURES
12 - 4.3 DUST EXCLUSION
12 - 4.4 PROTECTION FROM FIRE
12 - 4.5 POLLUTION BY COOLING MEDIUM (COOLANT)
13 - SECTION 5 STATIC CONVERTERS
13 - 5.1 OVERVOLTAGE LIMITATION
13 - 5.2 INTERFERENCE WITH COMMUNICATION AND CONTROL SYSTEMS
13 - 5.3 ELECTRICAL COUPLING
13 - 5.4 PROTECTION AGAINST INTERACTION BETWEEN EARTHING SYSTEMS
13 - 5.5 FEEDBACK SUPERVISION
13 - 5.6 LIMITATION OF HARMONICS
14 - SECTION 6 SWITCHING DEVICES
14 - 6.1 PREVENTION OF UNlNTENTlONAL OPERATION
14 - 6.2 ISOLATORS
14 - 6.3 INTERRUPTING CAPABILITY
14 - 6.4 PERSONNEL PROTECTION
15 - SECTION 7 CABLE SELECTION AND APPLICATION
15 - 7.1 PHASE CONDUCTORS
15 - 7.2 PROTECTIVE CONDUCTOR
15 - 7.3 ARMOURING AS PROTECTIVE CONDUCTOR
15 - 7.4 LIMITING TEMPERATURES UNDER SHORT CIRCUIT
15 - 7.5 PROTECTION AGAINST PARTIAL DISCHARGE
16 - 7.6 SEMICONDUCTING LAYERS
16 - 7.7 PROVISION OF SCREENS AND/OR ARMOURING FOR CABLES ABOVE 1000 V
16 - 7.8 IDENTIFICATION OF PROTECTIVE CONDUCTOR
16 - 7.9 PARTIAL DISCHARGE PERFORMANCE
16 - 7.10 TERMINATIONS OF FLEXIBLE CABLES
16 - 7.11 POWER CABLE TWIST LIMITATION
17 - 7.12 SHEATHING
17 - 7.13 SEGREGATION OF POWER AND CONTROL CORES
17 - 7.13.1 Single-core cables
17 - 7.13.2 Multicore cables
17 - 7.13.3 Composite multicore cables on reeling drums
17 - 7.14 SEPARATION OF CABLES IN RACKS
18 - 7.15 BENDING RADIUS FOR FLEXIBLE CABLES OVER 25 MM DIAMETER
19 - SECTION 8 CABLE CONNECTORS
19 - 8.1 USE OF PLUG/SOCKET CONNECTORS
19 - 8.2 BOLTED CONNECTIONS
20 - SECTION 9 CABLE DRUMS
20 - 9.1 INTRODUCTION
20 - 9.2 DRUM RATING FACTORS
20 - 9.3 CABLE TENSION LIMITS
21 - 9.4 DRUM DIAMETERS FOR FLEXIBLE CABLES
21 - 9.5 PERMISSIBLE REDUCTIONS IN DRUM DIAMETERS
21 - 9.6 REQUIREMENTS FOR CABLE `S' BENDS AND DIRECTION CHANGES
22 - SECTION 10 CONTROL CIRCUITS AND CONTROL DEVICES
22 - 10.1 PREVENTION OF UNINTENTIONAL OPERATION
22 - 10.2 LIMITATION OF LEAKAGE AND CAPACITANCE CURRENTS-UNEARTHED CONTROL CIRCUITS
22 - 10.3 MONITORING OF INSULATION-UNEARTHED CONTROL CIRCUITS
22 - 10.4 LIMITATION OF LEAKAGE AND CAPACITANCE CURRENTS-EARTHED CONTROL CIRCUITS
24 - SECTION 11 SAFETY CIRCUITS AND SAFETY DEVICES
24 - 11.1 GENERAL
24 - 11.2 CLOSED CIRCUIT PRINCIPLE
24 - 11.3 PROVING FUNCTION OPERATION PRINCIPLE
24 - 11.4 FAIL SAFE PRINCIPLES WITH SOLID STATE SWITCHING DEVICES
25 - SECTION 12 FIRE DETECTION AND PROTECTION SYSTEMS
25 - 12.1 INTRODUCTION
25 - 12.2 OBJECT
25 - 12.3 GENERAL PROTECTION REQUIREMENTS
25 - 12.3.1 General
25 - 12.3.2 Analysis of need for protection
25 - 12.3.3 Means of protection
26 - 12.4 FIXED DETECTION, ALARM AND EXTINGUISHMENT SYSTEMS AND THEIR EQUIPMENT
27 - 12.5 APPLICATION OF MEANS OF PROTECTION
27 - 12.5.1 General
27 - 12.5.2 Recommendations for the installation
27 - 12.5.3 Quantity of extinguishment medium available
27 - 12.5.4 Precautions for the installation
28 - 12.6 ADDITIONAL REQUIREMENTS AND RECOMMENDATIONS
28 - 12.6.1 Fire protection notices
28 - 12.6.2 Protection of equipment or plant
28 - 12.6.3 De-energization of electrical equipment
28 - 12.6.4 Flammable gases or liquids
28 - 12.6.5 Supplementary fire extinguishment equipment
28 - 12.6.6 Cableways and ducts
29 - APPENDIX A - TYPICAL ANALYSIS SHEET

Provides general requirements for the equipment and ancillaries associated with the electrical installation. Sections deal with electrical components, rotating machines, transformers, static converters, switching devices, cable selection and application, cable connectors, cable drums, control circuits and control devices, safety circuits and safety devices, and fire detection and protection systems.

This Standard sets out requirements for the equipment and ancillaries associated with electrical installations within the scope of AS 3007.1.

Committee
EL-023
DocumentType
Standard
ISBN
0 7337 6240 9
Pages
23
PublisherName
Standards Australia
Status
Superseded
SupersededBy
Supersedes
UnderRevision

First published as AS 3007.3-1982.Second edition 1987.Third edition 2004. First published as AS 3007.3-1982. Second edition 1987. Third edition 2004.

AS 2118.3-1997 Automatic fire sprinkler systems - Deluge
AS 2118.1-1999 Automatic fire sprinkler systems - General requirements
AS 1217.5-1985 Acoustics - Determination of sound power levels of noise sources Engineering methods for free-field conditions over a reflecting plane
AS 2441-1988 Installation of fire hose reels
AS 2380.1-1989 Electrical equipment for explosive atmospheres - Explosion-protection techniques General requirements (Reconfirmed 2013)
AS 2380.4-1994 Electrical equipment for explosive atmospheres - Explosion-protection techniques Pressurized rooms or pressurized enclosures (Reconfirmed 2013)
AS 1603.5-1996 Automatic fire detection and alarm systems Manual call points (Reconfirmed 2016)
AS 1603.13-1998 Automatic fire detection and alarm systems - Duct sampling units
AS 3007.1-2004 Electrical installations - Surface mines and associated processing plant - Scope and definitions
AS 1603.15-2002 Automatic fire detection and alarm systems - Remote indicators
AS 1603.1-1997 Automatic fire detection and alarm systems Heat detectors (Reconfirmed 2016)
AS 2380.9-1991 Electrical equipment for explosive atmospheres - Explosion-protection techniques Type of protection n - Non-sparking
AS 1217.4-1985 Acoustics - Determination of sound power levels of noise sources Engineering methods for special reverberation test room
AS 2441-2005 Installation of fire hose reels (Reconfirmed 2018)
AS 1670.3-2004 Fire detection, warning, control and intercom systems - System design, installation and commissioning - Fire alarm monitoring
AS 1603.7-1996 Automatic fire detection and alarm systems Optical beam smoke detectors (Reconfirmed 2016)
AS 3007.4-2004 Electrical installations - Surface mines and associated processing plant - Additional requirements for specific applications
AS 2665-2001 Smoke/heat venting systems - Design, installation and commissioning (Reconfirmed 2016)
AS/NZS 1850:1997 Portable fire extinguishers - Classification, rating and performance testing
AS 1603.2-1997 Automatic fire detection and alarm systems Point type smoke detectors (Reconfirmed 2016)
AS 1081.2-1990 Acoustics - Measurements of airborne noise emitted by rotating electrical machinery Survey method
AS 1217.3-1985 Acoustics - Determination of sound power levels of noise sources Precision methods for discrete-frequency and narrow-band sources in reverberation rooms
AS 1670.4-2004 Fire detection, warning, control and intercom systems - System design, installation and commissioning Sound systems and intercom systems for emergency purposes
AS 1217.2-1985 Acoustics - Determination of sound power levels of noise sources Precision methods for broad-band sources in reverberation rooms
AS 2380.6-1988 Electrical equipment for explosive atmospheres - Explosion-protection techniques Increased safety
AS 1603.6-1987 Automatic fire detection and alarm systems - Fire alarm bells
AS 2118.9-1995 Automatic fire sprinkler systems Piping support and installation (Reconfirmed 2013)
AS 1217.7-1985 Acoustics - Determination of sound power levels of noise sources - Survey method
AS 1603.16-2002 Automatic fire detection and alarm systems - In situ testers
AS 1603.4-1987 Automatic fire detection and alarm systems - Control and indicating equipment
AS 1603.3-1996 Automatic fire detection and alarm systems - Heat alarms
AS 1670.6-1997 Fire detection, warning, control and intercom systems - System design, installation and commissioning Smoke alarms
AS 2118.2-1995 Automatic fire sprinkler systems - Wall wetting sprinklers (Drenchers)
AS/NZS 1668.1:1998 The use of ventilation and airconditioning in buildings Fire and smoke control in multi-compartment buildings
AS 2118.4-1995 Automatic fire sprinkler systems - Residential
AS 1603.14-2001 Automatic fire detection and alarm systems - Point type carbon monoxide (CO) fire detectors
AS 2118.8-1997 Automatic fire sprinkler systems Minor modifications (Reconfirmed 2013)
AS 3007.2-2004 Electrical installations - Surface mines and associated processing plant - General protection requirements
AS 2118.6-1995 Automatic fire sprinkler systems - Combined sprinkler and hydrant
AS 1603.8-1996 Automatic fire detection and alarm systems Multi-point aspirated smoke detectors (Reconfirmed 2016)
AS 1670.1-2004 Fire detection, warning, control and intercom systems - System design, installation and commissioning Fire
AS 2444-2001 Portable fire extinguishers and fire blankets - Selection and location (Reconfirmed 2021)
AS 1217.6-1985 Acoustics - Determination of sound power levels of noise sources Precision methods for anechoic and hemi-anechoic rooms
AS 1603.11-2001 Automatic fire detection and alarm systems - Visual warning devices
AS 2380.7-1987 Electrical equipment for explosive atmospheres - Explosion-protection techniques - Intrinsic safety i
AS 1670.2-1997 Fire detection, warning, control and intercom systems - System design, installation and commissioning - Local fire
AS/NZS 61000.3.6:2001 Electromagnetic compatibility (EMC) Limits - Assessment of emission limits for distorting loads in MV and HV power systems (IEC 61000-3-6:1996, MOD)
AS/NZS 1221:1997 Fire hose reels (Reconfirmed 2020)
AS 1217.1-1985 Acoustics - Determination of sound power levels of noise sources - Guidelines for the use of basic Standards for the preparation of noise test codes
AS 2380.2-1991 Electrical equipment for explosive atmospheres - Explosion-protection techniques Flameproof enclosure d
AS 2118.10-1995 Automatic fire sprinkler systems Approval documentation (Reconfirmed 2013)
AS 2118.5-1995 Automatic fire sprinkler systems - Domestic

AS/NZS 4871.2:2010 Electrical equipment for mines and quarries Distribution, control and auxiliary equipment
AS/NZS 4871.1:2010 Electrical equipment for mines and quarries General requirements
AS/NZS 4871.6:2013 Electrical equipment for mines and quarries Diesel powered machinery and ancillary equipment
AS 1418.1-2002 Cranes, hoists and winches General requirements
AS 60204.1-2005 Safety of machinery - Electrical equipment of machines General requirements (IEC 60204-1, Ed. 5 (FDIS) MOD)
AS 5062-2006 Fire protection for mobile and transportable equipment
AS/NZS 4871.1:2012 Electrical equipment for mines and quarries General requirements
AS 3007.4-2004 Electrical installations - Surface mines and associated processing plant - Additional requirements for specific applications

View more information
US$69.34
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.