• There are no items in your cart

AS 3565.1-1998

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Meters for cold potable water - Volumetric chamber and turbine meters
Available format(s)

Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users

Superseded date

06-30-2017

Language(s)

English

Published date

01-01-1998

Preview

1 - AS 3565.1-1998 METERS FOR COLD POTABLE WATER - VOLUMETRIC CHAMBER AND TURBINE METERS
4 - PREFACE
5 - CONTENTS
7 - SECTION 1 SCOPE AND GENERAL
7 - 1.1 SCOPE
7 - 1.2 REFERENCED DOCUMENTS
8 - 1.3 DEFINITIONS
8 - 1.3.1 Error of measurement (Eq )
8 - 1.3.2 Flowrate (q)
8 - 1.3.3 Flow rate range
8 - 1.3.4 Maximum continuous flow rate (qcmax)
8 - 1.3.5 Maximum intermittent flow rate (qimax)
8 - 1.3.6 Maximum permissible error of measurement
8 - 1.3.7 Maximum error of measurement
8 - 1.3.8 Measurement class
8 - 1.3.9 Minimum flow rate (qmin)
8 - 1.3.10 Minimum registration flow rate(qreg)
8 - 1.3.11 Nominal flow rate (qn)
8 - 1.3.12 Pressure loss
8 - 1.3.13 Volume (V)
8 - 1.3.14 Water service
8 - 1.3.15 Working pressure
8 - 1.3.16 Working temperature
8 - 1.4 DESIGNATION OF SIZE
9 - 1.5 DESIGNATION OF CAPACITY
9 - 1.6 DIMENSIONS AND TOLERANCES
9 - 1.7 MARKING
9 - 1.7.1 Identification marks
9 - 1.7.2 Verification marks
9 - 1.8 AUSTRALIAN WATER AGENCIES-COMPLIANCE REQUIREMENTS
10 - SECTION 2 MATERIALS AND COMPONENTS
10 - 2.1 MATERIALS
10 - 2.1.1 General
10 - 2.1.2 Contamination of water
10 - 2.1.3 Copper Alloys
10 - 2.2 END CONNECTIONS
10 - 2.2.1 Threaded end connections
10 - 2.2.2 Flanged end connections
10 - 2.3 REGISTER
10 - 2.3.1 General
10 - 2.3.2 Register design
12 - 2.3.3 Number of decades
12 - 2.3.4 Indicators
12 - 2.3.5 Verification scale
13 - 2.4 ELECTRONIC OUTPUT DEVICE (EOD)
13 - 2.4.1 General
13 - 2.4.2 Types
14 - 2.4.3 Requirements
14 - 2.4.4 SMT
14 - 2.5 CALIBRATION ADJUSTMENT DEVICE
14 - 2.6 PROTECTIVE DEVICES
14 - 2.7 FROST PROTECTION
14 - 2.8 STRAINERS
15 - SECTION 3 PERFORMANCE REQUIREMENTS
15 - 3.1 GENERAL
15 - 3.2 MEASUREMENT CLASS
15 - 3.3 ULTRAVIOLET LIGHT EXPOSURE
15 - 3.4 TORQUE RESISTANCE OF THREADED END CONNECTIONS
15 - 3.5 WATERTIGHTNESS
15 - 3.6 NON-REVERSING DEVICE
15 - 3.7 REVERSE FLOW
15 - 3.8 PRESSURE LOSS
15 - 3.9 MAXIMUM ERROR OF MEASUREMENT
15 - 3.10 ENDURANCE
16 - SECTION 4 PERFORMANCE TESTS
16 - 4.1 TESTS AND SEQUENCE
16 - 4.2 APPARATUS
17 - APPENDIX A - PURCHASING GUIDELINES
17 - A1 GENERAL
17 - A2 INFORMATION TO BE SUPPLIED BY THE PURCHASER
18 - A3 CERTIFICATES
18 - A3.1 Certificate of compliance
18 - A3.2 Test certificate
19 - APPENDIX B - TECHNICAL DATA
19 - B1 SCOPE
19 - B2 TECHNICAL DATA
22 - APPENDIX C - ELECTRONIC METERS
22 - C1 SCOPE
22 - C2 REQUIREMENTS
22 - C2.1 General
22 - C2.2 Capability
22 - C2.3 Register
23 - APPENDIX D - ULTRAVIOLET LIGHT EXPOSURE TEST
23 - D1 SCOPE
23 - D2 PRINCIPLE
23 - D3 APPARATUS
23 - D4 PROCEDURE
24 - D5 REPORT
25 - APPENDIX E - TORQUE RESISTANCE OF THREADED END CONNECTIONS TEST
25 - E1 SCOPE
25 - E2 PRINCIPLE
25 - E3 APPARATUS
25 - E4 PROCEDURE
26 - E5 REPORT
27 - APPENDIX F - WATERTIGHTNESS TEST
27 - F1 SCOPE
27 - F2 PRINCIPLE
27 - F3 APPARATUS
27 - F4 PROCEDURE (see Figure F1)
28 - F5 REPORT
29 - APPENDIX G - NON-REVERSING DEVICE LEAKAGE TEST
29 - G1 SCOPE
29 - G2 PRINCIPLE
29 - G3 APPARATUS
29 - G4 PROCEDURE (see Figure F1)
29 - G5 CALCULATION
30 - G6 REPORT
31 - APPENDIX H - REVERSE FLOW TEST
31 - H1 SCOPE
31 - H2 PRINCIPLE
31 - H3 APPARATUS
31 - H4 PROCEDURE (see Figure H1)
32 - H5 REPORT
33 - APPENDIX I - PRESSURE LOSS TEST
33 - I1 SCOPE
33 - I2 PRINCIPLE
33 - I3 APPARATUS
34 - I4 PROCEDURE (See Figure I1)
35 - I5 CALCULATIONS
35 - I6 REPORT
36 - APPENDIX J - ERROR OF MEASUREMENT TEST
36 - J1 SCOPE
36 - J2 PRINCIPLE
36 - J3 APPARATUS
36 - J4 PROCEDURE
37 - J5 CALCULATIONS
38 - J6 REPORT
40 - APPENDIX K - ENDURANCE TEST
40 - K1 SCOPE
40 - K2 PRINCIPLE
40 - K3 APPARATUS
40 - K4 PROCEDURE (see Figure K1)
40 - K4.1 Meters with nominal flow rate (qn) equal to or less than 7.5 kL/h
41 - K4.2 Meters with nominal flow rate (qn) greater than 7.5 kL/h
41 - K5 CALCULATION
42 - K6 REPORT
43 - APPENDIX L - APPARATUS FOR TEST RIGS
43 - L1 SCOPE
43 - L2 CALIBRATED REFERENCE DEVICE
43 - L2.1 General
44 - L2.2 Parameters
44 - L3 POTABLE WATER SUPPLY
44 - L4 TEMPERATURE INDICATOR
44 - L5 TIMING DEVICE
44 - L6 PRESSURE INDICATOR
45 - L7 DIFFERENTIAL PRESSURE INDICATOR
45 - L8 FLOW RATE INDICATOR
45 - L9 PRESSURE TAPPINGS
48 - APPENDIX M - DETERMINATION OF COMPLIANCE
48 - M1 SCOPE
48 - M2 PRINCIPLE
48 - M3 PATTERN APPROVAL
48 - M4 INITIAL VERIFICATION

Specifies requirements for volumetric chamber and turbine meters with nominal flow rates not exceeding 40 kL/h and 250 kL/h, respectively, which may be fitted with electronic output devices (EOD). These meters are intended for installation in water services to measure, within the accuracy limits of the Class, the volume of cold potable water at working temperatures and pressures not exceeding 30 degrees Celsius and 1400 kPa, respectively.

This Standard specifies requirements for volumetric chamber and turbine meters with nominal flow rates not exceeding 40 kL/h and 250 kL/h, respectively, which may be fitted with electronic output devices (EOD). These meters are intended for installation in water services to measure, within the accuracy limits of the class, thevolume of cold potable water at working temperatures and pressures not exceeding 30C and 1400 kPa, respectively.This Standard is applicable to meters that are self-contained and capable of continuously determining, within the accuracy limits of the class, the volume of cold potable water that has flowed through them, and that are continuously indicating the volume on a cumulative basis.NOTE: Purchasing guidelines are given in Appendix A.

Committee
WS-024
DocumentType
Standard
ISBN
0 7337 2044 7
Pages
43
PublisherName
Standards Australia
Status
Superseded
SupersededBy
Supersedes
UnderRevision

Under Revision see DR 02384 First published as AS 3565-1988.Revised and redesignated AS 3565.1-1994.Second edition 1998. First published as AS 3565-1988. Revised and redesignated AS 3565.1-1994. Second edition 1998.

AS 4141.3-1995 Customer/utility information exchange Customer premises interfaces
AS 4087-1996 Metallic flanges for waterworks purposes
AS 3558.5-1999 Methods of testing plastics and composite materials sanitary plumbing fixtures Determination of degradation by ultraviolet light (Reconfirmed 2016)
AS/NZS ISO 9002:1994 Quality systems - Model for quality assurance in production, installation and servicing
AS 1939-1990 Degrees of protection provided by enclosures for electrical equipment (IP Code)
AS 1349-1986 Bourdon tube pressure and vacuum gauges (Reconfirmed 2018)
AS 1722.2-1992 Pipe threads of Whitworth form Fastening pipe threads (Reconfirmed 2017)
AS 2345-1992 Dezincification resistance of copper alloys
AS 3855-1994 Suitability of plumbing and water distribution systems products for contact with potable water
AS/NZS 3500.1.2:1998 National plumbing and drainage Water supply - Acceptable solutions

AS 3565.2-1996 Meters for cold potable water - Combination meters
AS 3565.3-1998 Meters for cold potable water - Water meters with integral dual check valves
AS/NZS 2845.1:1998 Water supply - Backflow prevention devices Materials, design and performance requirements
MP 52-2001 Manual of authorization procedures for plumbing and drainage products

View more information
US$82.57
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.