• AS 3565.3-2004

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    Meters for water supply - Water meters with integral dual check valves

    Available format(s):  Hardcopy, PDF 1 User, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Superseded date:  06-30-2017

    Language(s):  English

    Published date:  01-01-2004

    Publisher:  Standards Australia

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1 - AS 3565.3-2004 METERS FOR WATER SUPPLY - WATER METERS WITH INTEGRAL DUAL CHECK VALVES
    4 - PREFACE
    5 - CONTENTS
    6 - SECTION 1 SCOPE AND GENERAL
    6 - 1.1 SCOPE
    6 - 1.2 REFERENCED DOCUMENTS
    7 - 1.3 DEFINITIONS
    7 - 1.4 DESIGNATION OF SIZE
    7 - 1.5 DESIGNATION OF CAPACITY
    7 - 1.6 DIMENSIONS AND TOLERANCES
    7 - 1.7 MARKING
    7 - 1.8 AUSTRALIAN WATER AGENCIES-COMPLIANCE REQUIREMENTS
    8 - SECTION 2 MATERIALS AND COMPONENTS
    8 - 2.1 MATERIALS
    8 - 2.2 END CONNECTIONS
    8 - 2.3 REGISTER
    8 - 2.4 PROTECTIVE DEVICES
    8 - 2.5 FROST PROTECTION
    8 - 2.6 STRAINERS
    8 - 2.7 NON-RETURN VALVES
    8 - 2.8 SERVICEABILITY OF NON-RETURN VALVES
    9 - SECTION 3 PERFORMANCE REQUIREMENTS
    9 - 3.1 GENERAL
    9 - 3.2 ULTRAVIOLET LIGHT EXPOSURE
    9 - 3.3 TORQUE RESISTANCE OF THREADED END CONNECTIONS
    9 - 3.4 WATERTIGHTNESS
    9 - 3.5 PRESSURE LOSS
    9 - 3.6 MAXIMUM ERROR OF MEASUREMENT
    10 - 3.7 REVERSE PRESSURE
    10 - 3.8 NON-RETURN VALVE CLOSING PRESSURE
    10 - 3.9 METER ENDURANCE
    10 - 3.10 NON-RETURN VALVE ENDURANCE
    11 - SECTION 4 PERFORMANCE TESTS
    11 - 4.1 NUMBER OF SAMPLES, TESTS AND SEQUENCE
    11 - 4.2 APPARATUS
    12 - APPENDIX A - MEANS FOR DEMONSTRATING COMPLIANCE WITH THIS STANDARD
    12 - A1 SCOPE
    12 - A2 RELEVANCE
    12 - A3 PRODUCT CERTIFICATION
    12 - A3.1 Definitions
    13 - A4 TESTING
    13 - A4.1 General
    13 - A4.2 Type testing sampling
    13 - A4.3 Retesting
    13 - A4.4 Pattern approval
    13 - A4.5 Acceptability of tests

    Abstract - (Show below) - (Hide below)

    Provides requirements for volumetric chamber and turbine meters with permanent flow rates not exceeding 6.5 kL/h and which may be fitted with electronic output devices (EOD), incorporating two independent non-return valves, (Dual CVs) for low hazard protection of potable water.

    Scope - (Show below) - (Hide below)

    This Standard specifies requirements for volumetric, multi-jet, and single-jet meters incorporating two independent non-return valves (dual CVs) for low hazard protection of potable water supply. Water meters with integral dual check valves are intended for installation in water services to measure, within the accuracy limits of the class, the volume of cold potable water at working temperatures in the ranges of 0.3°C to 30°C and pressures not exceeding 1400 kPa, respectively. This Standard is applicable to meters that are self-contained and capable of continuously determining, within the accuracy limits of the class, the volume of cold potable water that has flowed through them, and that are continuously indicating the volume on a cumulative basis. Means for demonstrating compliance with this Standard are given in Appendix A NOTE: Purchasing guidelines are given in AS 3565.1.

    General Product Information - (Show below) - (Hide below)

    Committee WS-024
    Document Type Standard
    Publisher Standards Australia
    Status Superseded
    Superseded By
    Supersedes
    Under Revision

    History - (Show below) - (Hide below)

    First published as part of AS 3565.3-1998.
    Revised and designated in part as AS 3565.3-2004. First published as part of AS 3565.3-1998. Revised and designated in part as AS 3565.3-2004.

    Standards Referenced By This Book - (Show below) - (Hide below)

    HB 18.28-1991 Guidelines for third-party certification and accreditation General rules for a model third-party certification system for products
    AS 1722.2-1992 Pipe threads of Whitworth form Fastening pipe threads
    AS/NZS 2845.1:1998 Water supply - Backflow prevention devices Materials, design and performance requirements
    AS 4087-1996 Metallic flanges for waterworks purposes
    AS 2345-1992 Dezincification resistance of copper alloys
    AS 3565.1-2004 Meters for water supply Cold water meters
    AS/NZS 4020:2002 Testing of products for use in contact with drinking water

    Standards Referencing This Book - (Show below) - (Hide below)

    AS 3565.5-2004 Meters for water supply - Water meters with two integral single check valves
    AS 5200.000-2006 Technical specification for plumbing and drainage products Procedures for certification of plumbing and drainage products (Reconfirmed 2018)
    MP 52-2005 Manual of authorization procedures for plumbing and drainage products
    AS 5200.000-2005 Technical specification for plumbing and drainage products Procedures for certification of plumbing and drainage products
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective