AS/NZS 1580.108.1:1994
Current
The latest, up-to-date edition.
Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users
English
07-18-1994
Specifies non-destructive test methods for determining the dry film thickness on metallic substrates using magnetic torsion pull-off instruments, magnetic induction instruments and eddy current instruments.
This Standard sets out a general procedure for determining the thickness of non-magnetic coatings on steel or other metallic substrates using non-destructive testing techniques within the laboratory. It is intended for use with coatings which produce films that are firm and not subject to indentation by the instruments used. The coating thickness measurements may be obtained with magnetic torsional pull-off gauges, magnetic induction or eddy current type instruments. The method is not applicable to coatings of less than 20 µm thickness.NOTES:1 Site testing procedures are described in AS 3894.3.2 Direct magnetic pull-off gauges are not covered by this Standard.
| Committee |
CH/3
|
| DocumentType |
Standard
|
| ISBN |
0 7262 8971 X
|
| Pages |
5
|
| ProductNote |
Reconfirmed 18/09/2013This standard has been reconfirmed in Australia in 2013 and remains current in New Zealand. Reconfirmation Notice 18/09/2013
|
| PublisherName |
Standards Australia
|
| Status |
Current
|
| Supersedes | |
| UnderRevision |
First published as AS 1580.108.1-1975.Second edition 1980.Jointly revised and designated as Joint Standard AS/NZS 1580.108.1:1994.Reconfirmed 2013. First published as AS 1580.108.1-1975. Second edition 1980. Jointly revised and designated as Joint Standard AS/NZS 1580.108.1:1994.
| AS 1580.101.4-1986 | Paints and related materials - Methods of test Conditions of test, temperature controlled |
| AS 2310-1980 | Glossary of paint and painting terms |
| AS/NZS 1580.101.4:1999 | Paints and related materials - Methods of test Conditions of test - Temperature control (Reconfirmed 2013) |
| AS 3894.3-1993 | Site testing of protective coatings - Determination of dry film thickness |
| AS/NZS 2310:2002 | Glossary of paint and painting terms (Reconfirmed 2016) |
| AS 3894.3-2002 | Site testing of protective coatings Determination of dry film thickness (Reconfirmed 2013) |
| AS/NZS 3750.15:1998 | Paints for steel structures Inorganic zinc silicate paint (Reconfirmed 2013) |
| AS 3750.18-2002 | Paints for steel structures Moisture cure urethane (single-pack) systems |
| AS/NZS 3750.8:1994 | Paints for steel structures Vinyl paints - Primer, high-build and gloss (Reconfirmed 2013) |
| AS/NZS 3750.11:2009 | Paints for steel structures Chlorinated rubber - High-build and gloss |
| AS 3750.2-1994 | Paints for steel structures - Ultra high-build paint |
| AS 1580.408.4-2004 | Paints and related materials - Methods of test Adhesion (crosscut) (Reconfirmed 2019) |
| AS/NZS 3750.13:1997 | Paints for steel structures Epoxy primer (two-pack) |
| AS/NZS 2728:2013 | Prefinished/prepainted sheet metal products for interior/exterior building applications - Performance requirements |
| AS 2331.1.1-2001 | Methods of test for metallic and related coatings Local thickness tests - Micrographic examination of cross-sections |
| AS 2518-1992 | Fusion-bonded low-density polyethylene coating for pipes and fittings |
| AS/NZS 3750.11:1996 | Paints for steel structures - Chlorinated rubber - High-build and gloss |
| AS/NZS 3750.4:1994 | Paints for steel structures Bitumen paint (Reconfirmed 2013) |
| AS/NZS 3750.3:2008 | Paints for steel structures Heat resisting - Exterior (Reconfirmed 2020) |
| AS/NZS 3750.3:1994 | Paints for steel structures - Heat resisting - Exterior |
| AS/NZS 1580.602.2:1995 | Paints and related materials - Methods of test Measurement of specular gloss of non-metallic paint films at 20°, 60° and 85° (Reconfirmed 2013) |
| AS 1580.453.1-2003 | Paints and related materials - Methods of test Resistance to solvent immersion |
| AS/NZS 2728:1997 | Prefinished/prepainted sheet metal products for interior/exterior building applications - Performance requirements |
| AS 4049.3-2005 | Paints and related materials - Pavement marking materials Waterborne paint - For use with surface applied glass beads (Reconfirmed 2016) |
| AS/NZS 3750.14:1997 | Paints for steel structures High-build epoxy (two-pack) |
| AS 3750.10-2008 | Paints for steel structures Full gloss epoxy (two-pack) (Reconfirmed 2019) |
| AS/NZS 3750.12:1996 | Paints for steel structures Alkyd/micaceous iron oxide (Reconfirmed 2013) |
| AS/NZS 2728:2007 | Prefinished/prepainted sheet metal products for interior/exterior building applications - Performance requirements |
| AS 1580.408.2-2004 | Paints and related materials - Methods of test Adhesion - Knife test (Reconfirmed 2019) |
| AS/NZS 3750.1:2008 | Paints for steel structures Epoxy mastic (two-pack) - For rusted steel (Reconfirmed 2020) |
| AS 1580.402.1-2003 | Paints and related materials - Methods of test Bend test |
| AS/NZS 3750.5:2008 | Paints for steel structures Acrylic full gloss (two-pack) (Reconfirmed 2020) |
| AS/NZS 1580.481.1.6:1998 | Paints and related materials - Methods of test Coatings - Exposed to weathering - Degree of erosion (Reconfirmed 2013) |
| AS/NZS 3750.16:1998 | Paints for steel structures Waterborne primer and paint for galvanized, zinc/aluminium alloy-coated and zinc-primed steel (Reconfirmed 2013) |
| AS 3750.1-1994 | Paints for steel structures - Epoxy mastic (two-pack) - For rusted steel |
| AS/NZS 3750.21:2008 | Paints for steel structures Undercoat - Solvent-borne (Reconfirmed 2021) |
| AS 4049.1-2005 | Paints and related materials - Pavement marking materials Solvent-borne paint - For use with surface applied glass beads (Reconfirmed 2016) |
| AS/NZS 3750.5:1994 | Paints for steel structures - Acrylic full gloss (two-pack) |
| AS/NZS 3750.10:1994 | Paints for steel structures Full gloss epoxy (two-pack) |
| AS/NZS 3750.2:2008 | Paints for steel structures Ultra high-build paint (Reconfirmed 2020) |
| AS 1580.406.1-2004 | Paints and related materials - Methods of test Resistance to impact - Falling weight test (Gardner-type tester) |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.