Skip to content
Please enter a keyword to search
  • Preview

    AS/NZS 3750.2:2008

    Current The latest, up-to-date edition.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    Paints for steel structures Ultra high-build paint (Reconfirmed 2020)

    Available format(s):  Hardcopy, PDF 1 User, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Language(s):  English

    Published date:  05-18-2008

    Publisher:  Standards Australia

    Add to Watchlist

    Add To Cart

    Abstract - (Show below) - (Hide below)

    Specifies requirements for two-component ultra high-build paints for the protection of iron and steel against exterior corrosion in aggressive service conditions.

    Scope - (Show below) - (Hide below)

    This Standard specifies requirements for two-component ultra high-build paints for the protection of iron and steel against exterior corrosion in aggressive service conditions. They are suitable for application only by using high pressure, high volume airless spray equipment. Paints specified in this Standard comply with the requirements of Paint type C34 in AS/NZS 2312. These paints are produced in a limited colour range, usually white, grey or black.Ultra high-build (UHB) paints are classified as follows:(a) Type I, two-pack epoxy.(b) Type II, polyester.(c) Type III, vinyl ester.Ultra high-build paints are not intended to provide an aesthetically pleasing finish, but should provide long-term protection in aggressive atmospheric exposures for periods in excess of 15 years.NOTES:1 These paints may be used as detailed for system EPF1, in AS/NZS 2312.2 Appendix A contains recommendations which should be provided by the purchaser at the time of enquiry or order.3 Additional information on the use and application of ultra high-build paints is contained in Appendix B.

    General Product Information - (Show below) - (Hide below)

    Committee CH-003
    Document Type Standard
    Product Note Reconfirmed 11/09/2020.
    This standard has been reconfirmed in Australia in 2020 and remains current in New Zealand. Reconfirmation Notice 11/09/2020
    Publisher Standards Australia
    Status Current
    Supersedes

    History - (Show below) - (Hide below)

    Originated as AS 3750.2-1994.
    Revised and redesignated AS/NZS 3750.2:2008.
    Reconfirmed 2020. Originated as AS 3750.2-1994. Revised and redesignated AS/NZS 3750.2:2008.

    Standards Referenced By This Book - (Show below) - (Hide below)

    AS/NZS 1580.103.1:1995 Paints and related materials Methods of test - Examination and preparation of samples for testing (Reconfirmed 2013)
    AS 2854-2004 Tinplate cans for general use
    AS/NZS 1580.101.1:1999 Paints and related materials - Methods of test Conditions of test - Temperature, humidity and airflow control (Reconfirmed 2013)
    AS 1580.408.5-2006 Paints and related materials - Methods of test Adhesion - Pull-off test
    AS 3894.12-2002 Site testing of protective coatings Inspection report - Coating (Reconfirmed 2019)
    AS 3894.1-2002 Site testing of protective coatings Non-conductive coatings - Continuity testing - High voltage (brush) method (Reconfirmed 2013)
    AS 1580.406.1-2004 Paints and related materials - Methods of test Resistance to impact - Falling weight test (Gardner-type tester)
    AS 1627.4-2005 Metal finishing - Preparation and pretreatment of surfaces Abrasive blast cleaning of steel (Reconfirmed 2017)
    AS 4352-2005 Tests for coating resistance to cathodic disbonding
    AS 1145.5-2001 Determination of tensile properties of plastics materials Test conditions for fibre-reinforced plastic composites
    AS/NZS 1580.211.1:1995 Paints and related materials - Methods of test Degree of settling (Reconfirmed 2013)
    AS 1145.3-2001 Determination of tensile properties of plastics materials - Test conditions for films and sheets
    AS 1145.2-2001 Determination of tensile properties of plastics materials Test conditions for moulding and extrusion plastics
    AS 1145.4-2001 Determination of tensile properties of plastics materials Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
    AS 1580.301.1-2005 Paints and related materials - Methods of test Non-volatile content by mass
    AS/NZS 2310:2002 Glossary of paint and painting terms (Reconfirmed 2016)
    AS 1580.403.2-2006 Paints and related materials - Methods of test Abrasion resistance
    AS 3894.13-2002 Site testing of protective coatings Inspection report - Daily (Reconfirmed 2019)
    AS 3894.10-2002 Site testing of protective coatings Inspection report - Daily surface and ambient conditions (Reconfirmed 2019)
    AS/NZS 2312:2002 Guide to the protection of structural steel against atmospheric corrosion by the use of protective coatings
    AS/NZS 1580.104.1:2000 Paints and related materials - Methods of test Recommended materials for test panels (Reconfirmed 2013)
    AS 3894.4-2002 Site testing of protective coatings Assessment of degree of cure
    AS 2714-1993 The storage and handling of hazardous chemical materials - Class 5.2 substances (organic peroxides)
    AS/NZS 1580.108.1:1994 Paints and related materials - Methods of test Determination of dry film thickness on metallic substrates - Non-destructive methods (Reconfirmed 2013)
    AS/NZS 1580.101.5:1999 Paints and related materials - Methods of test Conditions of test - Temperature and humidity control (Reconfirmed 2013)
    AS 2905-2005 Steel drums
    AS 3894.14-2002 Site testing of protective coatings Inspection report - Daily painting (Reconfirmed 2019)
    AS/NZS 1580.205.4:1998 Paints and related materials - Methods of test Application properties - Airless spraying (Reconfirmed 2013)
    AS 1145.1-2001 Determination of tensile properties of plastics materials General principles
    AS 3894.11-2002 Site testing of protective coatings Equipment report (Reconfirmed 2019)
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective