ASME Y14.5M : 1994

Superseded View Superseded By

Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Preview

DIMENSIONING AND TOLERANCING

Publisher: American Society of Mechanical Engineers

Published: 01-01-2002

Available Formats: PDF - English - DRM, Hardcopy - English
More Info on product formats

Table of Contents - (Show below) - (Hide below)

Foreword
Standards Committee Roster
1 Scope, Definitions, and General Dimensioning
2 General Tolerancing and Related Principles
3 Symbology
4 Datum Referencing
5 Tolerances of Location
6 Tolerances of Form, Profile, Orientation, and
Runout
Appendices
A - Principal Changes and Improvements
B - Formulas for Positional Tolerancing
C - Form, Proportion, and Comparison of Symbols
D - Former Practices
E - Decision Diagrams for Geometric Control
Index

Abstract - (Show below) - (Hide below)

Describes uniform practices for stating and interpreting dimensioning, tolerancing, and related requirements for use on engineering drawings and in related documents.

General Product Information - (Show below) - (Hide below)

Published
Document Type	Standard
Status	Superseded
Publisher	American Society of Mechanical Engineers
ProductNote	Reconfirmed 1994
Pages
ISBN
Superseded By	ASME Y14.5 : 2009

Standards Referencing This Book - (Show below) - (Hide below)

ASME B5.10 : 1994	MACHINE TAPERS - SELF HOLDING AND STEEP TAPER SERIES
ASME Y14.6M : 81(R1998)	SCREW THREAD REPRESENTATION (METRIC SUPPLEMENT)
ASME B94.11M : 1993	TWIST DRILLS
ASME Y14.8M : 1996	CASTINGS AND FORGINGS
ASME Y14.1 : 2012	DECIMAL INCH DRAWING SHEET SIZE AND FORMAT - ENGINEERING DRAWING AND RELATED DOCUMENTATION PRACTICES
ASME Y14.3M : 94(R1999)	MULTI- AND SECTIONAL-VIEW DRAWINGS
ASME Y1.1 : 1989	ABBREVIATIONS FOR USE ON DRAWINGS AND IN TEXT,
ASME B46.1 : 2009	SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY)
ANSI B92.1 : 1996	INVOLUTE SPLINES AND INSPECTION
ASME B89.3.1 : 1972	MEASUREMENT OF OUT-OF-ROUNDNESS
ASME Y14.7.2 : 1978	GEAR AND SPLINE DRAWING STANDARDS - PART 2: BEVEL AND HYPOID GEARS
ASME B4.4M : 81(R94) ERRATA 95	INSPECTION OF WORKPIECES
ASME B1.2 : 1983	GAGES AND GAGING FOR UNIFIED INCH SCREW THREADS
ASME Y14.2M : 1992	LINE CONVENTIONS AND LETTERING
IEEE 268 : 1992	METRIC PRACTICE, STANDARD FOR
ASME Y14.36 : 78(R1993)	SURFACE TEXTURE SYMBOLS - DRAFTING STANDARDS
ASME Y14.7.1 : 1971	GEAR DRAWING STANDARDS - PART 1: FOR SPUR, HELICAL, DOUBLE HELICAL, AND RACK
(INACTIVE RECORD)ASME B4.2 : 1978	PREFERRED METRIC LIMITS AND FITS
ASME Y14.5.1M : 1994	MATHEMATICAL DEFINITION OF DIMENSIONING AND TOLERANCING PRINCIPLES
ASME Y14.6 : 2001	SCREW THREAD REPRESENTATION
ASME B94.6 : 1984	KNURLING
ANSI B92.2M : 1980	METRIC MODULE, INVOLUTE SPLINES

Add To Cart

Product Format

Quantity

add to cart

ASME Y14.5M : 1994

Table of Contents - (Show below) - (Hide below)

Abstract - (Show below) - (Hide below)

General Product Information - (Show below) - (Hide below)

Standards Referencing This Book - (Show below) - (Hide below)

Add To Cart

Publisher

Category

Sub Category

Access your standards online with a subscription?