• There are no items in your cart

ASME Y14.8M : 1996 : R2008

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

CASTINGS AND FORGINGS
Superseded date

09-30-2009

Published date

01-01-2008

Foreword
Standards Committee roster
1 Scope, definitions and terms
    1.1 General
    1.2 References
    1.3 Definitions
2 Drawing Presentation
    2.1 General
    2.2 Drawings Containing Separate Views
    2.3 Drawings, Containing Combined Views
    2.4 End Item Drawings
3 Drawing Requirements
    3.1 General
    3.2 Dimensions
    3.3 As-Cast/As-Forged Surfaces
    3.4 Corner Radii
    3.5 Die Closure Tolerance
    3.6 Draft Angle
    3.7 Fillet Radii
    3.8 Flash Extension
    3.9 Forging Plane
    3.10 Form Tolerances
    3.11 Marking
    3.12 Match Draft
    3.13 Mismatch
    3.14 Parting Lines
    3.15 Sharp corners
    3.16 Grain direction
    3.17 Special Requirements
    3.18 Profile Tolerances
4 Datum referencing
    4.1 General
    4.2 Application
    4.3 Datum Targets
    4.4 Machining Datum Reference Frame
    4.5 Tooling Centers and Tooling Holes
    4.6 Equalizing Datums
5 Drawing Notes
    5.1 General
    5.2 Drawing Note Items
Figures
1-1 Fillet and Corner Radii
2-1 Separate Views Drawing
2-2 Combined Views Drawing
2-3 End Item Drawing
3-1(a) Die Closure Not Specified
3-1(b) Die Closure Specified and Parting Line Indicated
3-1(c) Die Closure Specified and Parting Line Not
          Indicated
3-2 Draft Construction
3-3(a) Datum Plane and Forging Plane Parallel
3-3(b) Defined Forging Plane Not Parallel to Datum Plane
3-4(a) Flash Extension
3-4(b) Flash Extension and Mismatch
3-5 Surface Straightness Control Illustrating Effect
          of Form Control Exemption
3-6 Flatness Control Illustrating Effect of Form
          Control Exemption
3-7 Match Draft
3-8 Mismatch Tolerance
3-9 Parting Line Locations
3-10 Grain Direction Specified
3-11 Special Requirements
3-12 Profile Tolerancing
4-1 Datum Targets Establishing a Datum reference frame
4-2 Datum Targets Within Same Die Segment
4-3 Datum Targets Located Opposite Machined Surfaces
4-4 Datum Target Location - Optimum Spacing
          Consideration
4-5 Optimum Spacing of Datum Targets
4-6 Datum Targets Offset from the Datum plane
4-7 Effect of Draft and Parting Line on Datums
4-8 Placement of Repetitive Dimensions Affected by
          Draft
4-9 Machined Datum Features Located
4-10 Tooling Centers Establishing an Axis
4-11 Tooling Centers Establishing Center Planes
4-12 Movable Datum Targets Establishing a datum
          Center Plane
4-13 Movable Datum Targets Establishing Two Datum
          Center Planes
4-14 Equalized Datums Established by Fixed Datum
          Targets
4-15(a) Movable Datum Target Symbol Application
4-15(b) Movable Datum Target Symbol Form and Proportion
Appendices
A Glossary
A1 General
A2 Casting Terms
A3 Forging Terms
B Sample Notes
B1 General
B2 Sample Casting Notes
B3 Sample Forging Notes
C Profile Tolerance System for Dimensioning and
          Tolerancing Casting/Forging Drawings
C1 General
C2 Profile Tolerance System
C3 Figures
C4 Drafting Practice
C5 Application to a Combined View (Casting/Forging
          and Machining Requirements) Drawings
D Sample Drawing
Figures
C-1 Origin of Draft and Parting Line
C-2 Machine Allowance - Surface Without Draft
C-3 Machine Allowance - Surface With Draft
C-4 Machine Allowance - Portion of Surface with Draft
C-5 Machine Allowance - Chamfered Corner
C-6 Machine Allowance - Fillet
C-7 Combined View (Casting and Machining Requirements)
          Drawing
D-1 Precision Forging Drawing Sample

Covers the definition of terms and features unique to casting and forging technologies with recommendations for their uniform description and inclusion on engineering drawings and related documents. Unless otherwise specified, any reference to features, parts or processes shall be interpreted as applying to both castings and forgings. Castings and forgings are delineated as casting and forging throughout the Standard.

DevelopmentNote
Also included in ASME Y14.41 REFERENCED STANDARDS (PKG). (08/2003)
DocumentType
Standard
ProductNote
Reconfirmed 2008
PublisherName
American Society of Mechanical Engineers
Status
Superseded
SupersededBy
Supersedes

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.