• There are no items in your cart

ASTM A 276/A276M : 2017 : REDLINE

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Stainless Steel Bars and Shapes
Available format(s)

PDF

Superseded date

08-18-2023

Language(s)

English

Published date

03-21-2017

CONTAINED IN VOL. 01.03, 2017 Defines hot-finished or cold-finished bars except bars for reforging.

1.1This specification covers hot-finished or cold-finished bars except bars for reforging (Note 1). It includes rounds, squares, and hexagons, and hot-rolled or extruded shapes, such as angles, tees, and channels in the more commonly used types of stainless steels. The free-machining types (Note 2) for general corrosion resistance and high-temperature service are covered in a separate specification.

Note 1:For bars for reforging, see Specification A314.

Note 2:For free-machining stainless bars designed especially for optimum machinability, see Specification A582/A582M.

Note 3:There are standards covering high nickel, chromium, austenitic corrosion, and heat-resisting alloy materials. These standards are under the jurisdiction of ASTM Subcommittee B02.07 and may be found in Annual Book of ASTM Standards, Vol. 02.04.

1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.

Committee
A 01
DevelopmentNote
Supersedes ASTM A 276. (02/2015)
DocumentType
Redline
Pages
8
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

ASTM A 1082/A1082M : 2016 : REDLINE Standard Specification for High Strength Precipitation Hardening and Duplex Stainless Steel Bolting for Special Purpose Applications
MIL-DTL-18030 Revision F:2018 Valves, Control, Air-Diaphragm-Operated (Complete with Pneumatic Instrumentation)
AASHTO M 292M/M 292 : 2015 SPECIFICATION FOR CARBON AND ALLOY STEEL NUTS FOR BOLTS FOR HIGH-PRESSURE OR HIGH-TEMPERATURE SERVICE, OR BOTH
MIL-DTL-18436 Revision G:2017 Valves, Check - Bronze -and Steel-Body
MIL-DTL-28748-17 Revision B:2016 CONNECTORS, ELECTRICAL, RECTANGULAR, RACK AND PANEL, HARDWARE FOR
MIL-DTL-6001 Revision B:2013 FITTINGS; AIRCRAFT, SOLDER TYPE, TUBE
AWWA C512 : 2015 AIR-RELEASE, AIR/VACUUM, AND COMBINATION AIR VALVES FOR WATER AND WASTEWATER SERVICE
AWWA C515 : 2015 REDUCED-WALL, RESILIENT-SEATED GATE VALVES FOR WATER SUPPLY SERVICE
ANSI/AWWA C514 : 2015 AIR VALVE AND VENT INFLOW PREVENTER ASSEMBLIES FOR POTABLE WATER DISTRIBUTION SYSTEM AND STORAGE FACILITIES
AWWA E103 : 2015 HORIZONTAL AND VERTICAL LINE-SHAFT PUMPS
ACI 301 : 2016 SPECIFICATIONS FOR STRUCTURAL CONCRETE
AWWA C541 : 2016 HYDRAULIC AND PNEUMATIC CYLINDER AND VANE-TYPE ACTUATORS FOR VALVES AND SLIDE GATES
SBAC TS 220 : 1 TECHNICAL SPECIFICATION FOR UNION NUTS, SELF-LOCKING (UNIFIED THREADS) - HIGH TEMPERATURE NICKEL ALLOY INCONEL 718 CLASSIFICATION R[M] >= 1270 MPA (185000 LBF/IN[2]) @ T[A]/+705 DEGREES C
AASHTO M 334M/M 334 : 2017 SPECIFICATION FOR UNCOATED, CORROSION-RESISTANT, DEFORMED AND PLAIN CHROMIUM ALLOYED, BILLET-STEEL BARS FOR CONCRETE REINFORCEMENT AND DOWELS
ASME B31.3:2016 PROCESS PIPING
ASTM A 955/A 955M : 2018-02 SPECIFICATION FOR DEFORMED AND PLAIN STAINLESS-STEEL BARS FOR CONCRETE REINFORCEMENT
MIL-DTL-18866 Revision J:2015 Fittings, Hydraulic Tube, Flared, 37 Degree and Flareless, General Specification for
ASTM A 1040 : 2017 : REDLINE Standard Guide for Specifying Harmonized Standard Grade Compositions for Wrought Carbon, Low-Alloy, and Alloy Steels
MSS SP 81 : 2017 STAINLESS-STEEL OR STAINLESS-STEEL-LINED, BONNETLESS, KNIFE GATE VALVES WITH FLANGED ENDS
MIL-DTL-83798 Revision D:2008 FITTING, RUBBER HOSE, LIGHTWEIGHT, MEDIUM PRESSURE, GENERAL SPECIFICATION FOR
AASHTO MP 18M/MP 18 : 1900 SPECIFICATION FOR UNCOATED, CORROSION-RESISTANT, DEFORMED AND PLAIN ALLOY, BILLET-STEEL BARS FOR CONCRETE REINFORCEMENT AND DOWELS
ASTM F 2854 : 2010 Standard Specification for Push-Fit Crosslinked Polyethylene (PEX) Mechanical Fittings for Crosslinked Polyethylene (PEX) Tubing
ASTM F 2929 : 2017 : REDLINE Standard Specification for Crosslinked Polyethylene (PEX) Tubing of 0.070 in. Wall and Fittings for Radiant Heating Systems up to 75 psig
MS18197 Revision G:2016 GUIDE PIN, ELECTRICAL CONNECTOR MALE AND FEMALE
MSS SP 99 : 2016 INSTRUMENT VALVES
AASHTO T 375M/T 375 : 2017 METHOD OF TEST FOR IDENTIFICATION OF IRON-BASED ALLOY STEEL BARS FOR CONCRETE REINFORCEMENT OR DOWELS BY HANDHELD X-RAY FLUORESCENCE (XRF) SPECTROMETER
MIL-DTL-52525 Revision F:2008 FITTINGS, HOSE, HYDRAULIC, REUSABLE, FIELD-ATTACHABLE AND CLAMP-HALVES, TO MATE WITH SAE-J517 TYPE HOSES, GENERAL SPECIFICATION FOR
MS18196 Revision G:2016 JACKSCREW, ELECTRICAL CONNECTOR, MALE AND FEMALE, FIXED
AWWA C509 : 2015 RESILIENT-SEATED GATE VALVES FOR WATER SUPPLY SERVICE
ACI 301M : 2016 SPECIFICATIONS FOR STRUCTURAL CONCRETE
ASTM F 2854 : 2010 : R2016 Standard Specification for Push-Fit Crosslinked Polyethylene (PEX) Mechanical Fittings for Crosslinked Polyethylene (PEX) Tubing
MIL-DTL-17849 Revision F:2018 Strainers, Sediment, Pipeline, Duplex (with and without Magnet)
MIL-DTL-24578 Revision C:2015 VALVES, GLOBE, PRESSURE INSTRUMENT, STEM TEST CONNECTION, UNION END
MS27069 Revision H:2017 SOCKET, HOSE COUPLING
MIL-DTL-24356 Revision B:2017 Couplings and Split Clamps, 2½-, 4-, 6-, and 7-Inch Segmented, Reattachable, for Refueling-At-Sea Hose
ASTM F 3184 : 2016 Standard Specification for Additive Manufacturing Stainless Steel Alloy (UNS S31603) with Powder Bed Fusion

SAE J 1086 : 2012 NUMBERING METALS AND ALLOYS
ASTM E 527 : 2016 : REDLINE Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
ASTM A 1058 : 2014 : REDLINE Standard Test Methods for Mechanical Testing of Steel Products—Metric

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.