• There are no items in your cart

ASTM A 674 : 2018

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Practice for Polyethylene Encasement for Ductile Iron Pipe for Water or Other Liquids
Available format(s)

Hardcopy , PDF

Superseded date

11-08-2022

Language(s)

English

Published date

12-05-2018

This practice covers materials and installation procedures for polyethylene encasement to be applied to underground installations of ductile iron pipe.

1.1This practice covers materials and installation procedures for polyethylene encasement to be applied to underground installations of ductile iron pipe. It may also be used for polyethylene encasement of fittings, valves, and other appurtenances to ductile iron pipe systems.

1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.2.1Important SI values are provided in brackets. Also, certain important SI values appear without brackets or parentheses.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
A 04
DocumentType
Standard Practice
Pages
8
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 1922 : 2008 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 1709 : 2022 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 1709 : 2004 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 4976 : 2006 Standard Specification for Polyethylene Plastics Molding and Extrusion Materials
ASTM D 4976 : 2000 : REV B Standard Specification for Polyethylene Plastics Molding and Extrusion Materials
ASTM D 4976 : 2004 : REV A Standard Specification for Polyethylene Plastics Molding and Extrusion Materials
ASTM D 1922 : 2015 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 1922 : 2006 : REV A Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 4976 : 2004 Standard Specification for Polyethylene Plastics Molding and Extrusion Materials
ASTM D 1709 : 2015 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 4976 : 2012 Standard Specification for Polyethylene Plastics Molding and Extrusion Materials
ASTM D 1922 : 2003 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 1709 : 2009 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 1709 : 1998 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 4976 : 2002 Standard Specification for Polyethylene Plastics Molding and Extrusion Materials
ASTM D 1709 : 2001 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 1709 : 2016 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 1922 : 2015 : R2020 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 1709 : 2008 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 1922 : 2003 : REV A Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 4976 : 2002 : EDT 1 Standard Specification for Polyethylene Plastics Molding and Extrusion Materials
ASTM D 1922 : 2005 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 1709 : 2016 : REV A : EDT 1 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 1709 : 2003 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 1922 : 2000 : REV A Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 1922 : 2006 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 1709 : 2015 : REV A Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
ASTM D 1922 : 2009 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 4976 : 2012 : REV A Standard Specification for Polyethylene Plastics Molding and Extrusion Materials
ASTM D 1709 : 2016 : REV A Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.