• There are no items in your cart

ASTM B 746/B746M : 2016 : REDLINE

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Corrugated Aluminum Alloy Structural Plate for Field-Bolted Pipe, Pipe-Arches, and Arches
Available format(s)

PDF

Superseded date

06-17-2022

Language(s)

English

Published date

11-29-2016

CONTAINED IN VOL. 02.02, 2016 Defines corrugated aluminum alloy structural plate used in the construction of pipe, pipe-arches, arches, underpasses, box culverts, and special shapes for field assembly.

1.1This specification covers corrugated aluminum alloy structural plate used in the construction of pipe, pipe-arches, arches, underpasses, box culverts, and special shapes for field assembly. Appropriate fasteners are also described. The pipe, arches, and other shapes are generally used for drainage purposes, pedestrian and vehicular underpasses, and utility tunnels. Aluminum box culvert shapes are covered in Specification B864/B864M.

1.2This specification does not include requirements for bedding, backfill, or the relationship between earth cover load and plate thickness of the pipe. Experience has shown that the successful performance of this product depends upon the proper selection of plate thickness, type of bedding and backfill, controlled manufacture in the plant, and care in the installation. The purchaser must correlate the above factors and also the corrosion and abrasion requirements of the field installation with the plate thickness. The structural design of corrugated aluminum structural plate pipe and the proper installation procedures are given in Practices B790/B790M and B789/B789M, respectively. A procedure for using life-cycle cost analysis techniques to evaluate alternate drainage system designs using corrugated metal pipe is given in Practice A930.

1.3The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other.

Committee
B 07
DocumentType
Redline
Pages
5
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

S6.1-14 Commentary on S6-14, Canadian Highway Bridge Design Code
S6-14 Canadian Highway Bridge Design Code
ASTM B 881 : 2017 : REDLINE Standard Terminology Relating to Aluminum- and Magnesium-Alloy Products
ASTM B 790/B790M : 2016 : REDLINE Standard Practice for Structural Design of Corrugated Aluminum Pipe, Pipe-Arches, and Arches for Culverts, Storm Sewers, and Other Buried Conduits
ASTM B 789/B789M : 2016 : REDLINE Standard Practice for Installing Corrugated Aluminum Structural Plate Pipe for Culverts and Sewers

ASTM F 467M : 2006 : REV A : EDT 2 Standard Specification for Nonferrous Nuts for General Use (Metric)
ASME B18.2.1 : 2012 SQUARE, HEX, HEAVY HEX, AND ASKEW HEAD BOLTS AND HEX, HEAVY HEX, HEX FLANGE, LOBED HEAD, AND LAG SCREWS (INCH SERIES)
ASTM B 790/B790M : 2016 : REDLINE Standard Practice for Structural Design of Corrugated Aluminum Pipe, Pipe-Arches, and Arches for Culverts, Storm Sewers, and Other Buried Conduits
ASME B18.2.4.6M : 2010 METRIC HEAVY HEX NUTS
ASTM B 666/B666M : 2015 : REDLINE Standard Practice for Identification Marking of Aluminum and Magnesium Products
ASTM F 593 : 2017 : REDLINE Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
ASTM B 209M : 2014 : REDLINE Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate (Metric)
ASTM B 221 : 2014 : REDLINE Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes
ASTM A 563 : 2015 : REDLINE Standard Specification for Carbon and Alloy Steel Nuts
ASTM B 789/B789M : 2016 : REDLINE Standard Practice for Installing Corrugated Aluminum Structural Plate Pipe for Culverts and Sewers
ASTM B 209 : 2014 : REDLINE Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate
ASTM A 449 : 2014 : REDLINE Standard Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use
ASME B18.2.2 : 2015 NUTS FOR GENERAL APPLICATIONS: MACHINE SCREW NUTS, HEX, SQUARE, HEX FLANGE, AND COUPLING NUTS (INCH SERIES)

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.