• There are no items in your cart

ASTM C 1273 : 2018

Current
Current

The latest, up-to-date edition.

Standard Test Method for Tensile Strength of Monolithic Advanced Ceramics at Ambient Temperatures
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

07-01-2018

1.1This test method covers the determination of tensile strength under uniaxial loading of monolithic advanced ceramics at ambient temperatures. This test method addresses, but is not restricted to, various suggested test specimen geometries as listed in the appendixes. In addition, test specimen fabrication methods, testing modes (force, displacement, or strain control), testing rates (force rate, stress rate, displacement rate, or strain rate), allowable bending, and data collection and reporting procedures are addressed. Note that tensile strength as used in this test method refers to the tensile strength obtained under uniaxial loading.

1.2This test method applies primarily to advanced ceramics that macroscopically exhibit isotropic, homogeneous, continuous behavior. While this test method applies primarily to monolithic advanced ceramics, certain whisker- or particle-reinforced composite ceramics as well as certain discontinuous fiber-reinforced composite ceramics may also meet these macroscopic behavior assumptions. Generally, continuous fiber ceramic composites (CFCCs) do not macroscopically exhibit isotropic, homogeneous, continuous behavior and application of this practice to these materials is not recommended.

1.3Values expressed in this test method are in accordance with the International System of Units (SI) and IEEE/ASTM SI 10.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 7.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
C 28
DocumentType
Test Method
Pages
19
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

ASTM C 1683 : 2010 : R2019 Standard Practice for Size Scaling of Tensile Strengths Using Weibull Statistics for Advanced Ceramics
ASTM C 1773 : 2017 Standard Test Method for Monotonic Axial Tensile Behavior of Continuous Fiber-Reinforced Advanced Ceramic Tubular Test Specimens at Ambient Temperature
ASTM C 1368 : 2018 Standard Test Method for Determination of Slow Crack Growth Parameters of Advanced Ceramics by Constant Stress Rate Strength Testing at Ambient Temperature
ASTM C 1291 : 2018 Standard Test Method for Elevated Temperature Tensile Creep Strain, Creep Strain Rate, and Creep Time to Failure for Monolithic Advanced Ceramics
ASTM C 1361 : 2010 : R2019 Standard Practice for Constant-Amplitude, Axial, Tension-Tension Cyclic Fatigue of Advanced Ceramics at Ambient Temperatures

ASTM C 1145 : 2019 Standard Terminology of Advanced Ceramics
ASTM E 83 : 2023 Standard Practice for Verification and Classification of Extensometer Systems
ASTM E 1012 : 2014 Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application
ASTM C 1322 : 2005 : REV B Standard Practice for Fractography and Characterization of Fracture Origins in Advanced Ceramics
ASTM C 1145 : 1998 Standard Terminology of Advanced Ceramics
ASTM C 1161 : 2002 : REV C : R2008 Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature
ASTM C 1145 : 2006 Standard Terminology of Advanced Ceramics
ASTM E 83 : 2000 : EDT 1 Standard Practice for Verification and Classification of Extensometer
ASTM C 1161 : 2002 : REV C : R2008 : EDT 1 Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature
ASTM E 83 : 2016 Standard Practice for Verification and Classification of Extensometer Systems
ASTM C 1161 : 2018 : R2023 Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature
ASTM E 83 : 1998 : EDT 1 Standard Practice for Verification and Classification of Extensometer
ASTM C 1322 : 2015 Standard Practice for Fractography and Characterization of Fracture Origins in Advanced Ceramics
ASTM C 1322 : 2005 : REV A Standard Practice for Fractography and Characterization of Fracture Origins in Advanced Ceramics
ASTM E 337 : 2015 : R2023 Standard Test Method for Measuring Humidity with a Psychrometer (the Measurement of Wet- and Dry-Bulb Temperatures)
ASTM C 1145 : 2005 Standard Terminology of Advanced Ceramics
ASTM C 1161 : 2002 : REV C : EDT 1 Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature
ASTM E 337 : 2015 Standard Test Method for Measuring Humidity with a Psychrometer (the Measurement of Wet- and Dry-Bulb Temperatures)
ASTM E 6 : 2002 Standard Terminology Relating to Methods of Mechanical Testing
ASTM E 1012 : 1999 Standard Practice for Verification of Specimen Alignment Under Tensile Loading
ASTM E 1012 : 2012 Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application
ASTM C 1322 : 2005 : REV B : EDT 1 Standard Practice for Fractography and Characterization of Fracture Origins in Advanced Ceramics
ASTM C 1161 : 2002 : REV A Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature
ASTM E 1012 : 2014 : EDT 1 Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application
ASTM C 1239 : 2006 : REV A Standard Practice for Reporting Uniaxial Strength Data and Estimating Weibull Distribution Parameters for Advanced Ceramics
ASTM C 1145 : 2003 Standard Terminology of Advanced Ceramics
ASTM C 1239 : 2013 : R2018 Standard Practice for Reporting Uniaxial Strength Data and Estimating Weibull Distribution Parameters for Advanced Ceramics
ASTM C 1322 : 2005 : REV B : R2010 Standard Practice for Fractography and Characterization of Fracture Origins in Advanced Ceramics
ASTM C 1322 : 1996 : REV A Standard Practice for Fractography and Characterization of Fracture Origins in Advanced Ceramics
ASTM D 3379 : 1975 : R1989 : EDT 1 Standard Test Method for Tensile Strength and Young's Modulus for High-Modulus Single-Filament Materials (Withdrawn 1998)
ASTM C 1161 : 2018 Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature
ASTM E 1012 : 2012 : EDT 1 Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application
ASTM C 1161 : 2002 Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature
ASTM C 1322 : 2002 Standard Practice for Fractography and Characterization of Fracture Origins in Advanced Ceramics
ASTM E 6 : 2015 : EDT 3 Standard Terminology Relating to Methods of Mechanical Testing
ASTM C 1239 : 2000 Standard Practice for Reporting Uniaxial Strength Data and Estimating Weibull Distribution Parameters for Advanced Ceramics
ASTM E 6 : 2023 : REV A Standard Terminology Relating to Methods of Mechanical Testing
ASTM E 1012 : 2005 Standard Practice for Verification of Test Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application
ASTM C 1145 : 2006 : R2013 Standard Terminology of Advanced Ceramics
ASTM C 1161 : 2013 Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature
ASTM C 1239 : 2000 : R2005 Standard Practice for Reporting Uniaxial Strength Data and Estimating Weibull Distribution Parameters for Advanced Ceramics
ASTM C 1322 : 2002 : REV A Standard Practice for Fractography and Characterization of Fracture Origins in Advanced Ceramics
ASTM E 4 : 2021 Standard Practices for Force Calibration and Verification of Testing Machines
ASTM C 1145 : 2002 Standard Terminology of Advanced Ceramics
ASTM C 1322 : 2015 : R2019 Standard Practice for Fractography and Characterization of Fracture Origins in Advanced Ceramics
ASTM E 6 : 2015 : EDT 4 : REDLINE Standard Terminology Relating to Methods of Mechanical Testing
ASTM C 1161 : 1994 : R1996 Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature
ASTM C 1239 : 2006 Standard Practice for Reporting Uniaxial Strength Data and Estimating Weibull Distribution Parameters for Advanced Ceramics
ASTM C 1145 : 2002 : REV A Standard Terminology of Advanced Ceramics
ASTM C 1161 : 2002 : REV C Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature
ASTM C 1322 : 2005 Standard Practice for Fractography and Characterization of Fracture Origins in Advanced Ceramics
ASTM E 6 : 2015 : EDT 4 Standard Terminology Relating to Methods of Mechanical Testing
ASTM E 6 : 2023 Standard Terminology Relating to Methods of Mechanical Testing
ASTM C 1145 : 2001 Standard Terminology of Advanced Ceramics
ASTM C 1239 : 2013 Standard Practice for Reporting Uniaxial Strength Data and Estimating Weibull Distribution Parameters for Advanced Ceramics
ASTM C 1239 : 2007 Standard Practice for Reporting Uniaxial Strength Data and Estimating Weibull Distribution Parameters for Advanced Ceramics
ASTM C 1145 : 2006 : R2013 : EDT 1 Standard Terminology of Advanced Ceramics
ASTM E 1012 : 2019 Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application
ASTM C 1161 : 2002 : REV B Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature

View more information
US$69.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.