• There are no items in your cart

ASTM C 1275 : 2018

Current
Current

The latest, up-to-date edition.

Standard Test Method for Monotonic Tensile Behavior of Continuous Fiber-Reinforced Advanced Ceramics with Solid Rectangular Cross-Section Test Specimens at Ambient Temperature
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-01-2018

1.1This test method covers the determination of tensile behavior including tensile strength and stress-strain response under monotonic uniaxial loading of continuous fiber-reinforced advanced ceramics at ambient temperature. This test method addresses, but is not restricted to, various suggested test specimen geometries as listed in the appendix. In addition, test specimen fabrication methods, testing modes (force, displacement, or strain control), testing rates (force rate, stress rate, displacement rate, or strain rate), allowable bending, and data collection and reporting procedures are addressed. Note that tensile strength as used in this test method refers to the tensile strength obtained under monotonic uniaxial loading where monotonic refers to a continuous nonstop test rate with no reversals from test initiation to final fracture.

1.2This test method applies primarily to all advanced ceramic matrix composites with continuous fiber reinforcement: unidirectional (1D), bidirectional (2D), and tridirectional (3D). In addition, this test method may also be used with glass (amorphous) matrix composites with 1D, 2D, and 3D continuous fiber reinforcement. This test method does not directly address discontinuous fiber-reinforced, whisker-reinforced, or particulate-reinforced ceramics, although the test methods detailed here may be equally applicable to these composites.

1.3Values expressed in this test method are in accordance with the International System of Units (SI) and IEEE/ASTM SI 10.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 7 and 8.2.5.2.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
C 28
DocumentType
Test Method
Pages
22
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

ASTM C 1783 : 2015 Standard Guide for Development of Specifications for Fiber Reinforced Carbon-Carbon Composite Structures for Nuclear Applications
ASTM C 1360 : 2017 Standard Practice for Constant-Amplitude, Axial, Tension-Tension Cyclic Fatigue of Continuous Fiber-Reinforced Advanced Ceramics at Ambient Temperatures
ASTM C 1337 : 2017 Standard Test Method for Creep and Creep Rupture of Continuous Fiber-Reinforced Advanced Ceramics Under Tensile Loading at Elevated Temperatures
ASTM C 1835 : 2016 Standard Classification for Fiber Reinforced Silicon Carbide-Silicon Carbide (SiC-SiC) Composite Structures
ASTM C 1869 : 2018 Standard Test Method for Open-Hole Tensile Strength of Fiber-Reinforced Advanced Ceramic Composites
ASTM C 1793 : 2015 Standard Guide for Development of Specifications for Fiber Reinforced Silicon Carbide-Silicon Carbide Composite Structures for Nuclear Applications
ASTM C 1469 : 2010 : R2015 Standard Test Method for Shear Strength of Joints of Advanced Ceramics at Ambient Temperature
ASTM C 1836 : 2016 Standard Classification for Fiber Reinforced Carbon-Carbon Composite Structures
ASTM C 1468 : 2019 : REV A Standard Test Method for Transthickness Tensile Strength of Continuous Fiber-Reinforced Advanced Ceramics at Ambient Temperature

ASTM C 1145 : 2019 Standard Terminology of Advanced Ceramics
ASTM E 83 : 2023 Standard Practice for Verification and Classification of Extensometer Systems
ASTM E 177 : 1990 : REV A : R1996 Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods
ASTM E 1012 : 2014 Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application
ASTM C 1145 : 1998 Standard Terminology of Advanced Ceramics
ASTM C 1145 : 2006 Standard Terminology of Advanced Ceramics
ASTM D 3878 : 2002 : REV A Standard Terminology for Composite Materials
ASTM E 83 : 2000 : EDT 1 Standard Practice for Verification and Classification of Extensometer
ASTM D 3878 : 2023 Standard Terminology for Composite Materials
ASTM E 83 : 2016 Standard Practice for Verification and Classification of Extensometer Systems
ASTM D 3878 : 2015 Standard Terminology for Composite Materials
ASTM D 3878 : 2019 Standard Terminology for Composite Materials
ASTM E 83 : 1998 : EDT 1 Standard Practice for Verification and Classification of Extensometer
ASTM D 3878 : 2000 Standard Terminology Composite Materials
ASTM E 337 : 2015 : R2023 Standard Test Method for Measuring Humidity with a Psychrometer (the Measurement of Wet- and Dry-Bulb Temperatures)
ASTM C 1145 : 2005 Standard Terminology of Advanced Ceramics
ASTM E 337 : 2015 Standard Test Method for Measuring Humidity with a Psychrometer (the Measurement of Wet- and Dry-Bulb Temperatures)
ASTM E 6 : 2002 Standard Terminology Relating to Methods of Mechanical Testing
ASTM E 691 : 2020 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 1012 : 1999 Standard Practice for Verification of Specimen Alignment Under Tensile Loading
ASTM E 1012 : 2012 Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application
ASTM E 1012 : 2014 : EDT 1 Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application
ASTM C 1239 : 2006 : REV A Standard Practice for Reporting Uniaxial Strength Data and Estimating Weibull Distribution Parameters for Advanced Ceramics
ASTM D 3878 : 2003 : REV A Standard Terminology for Composite Materials
ASTM C 1145 : 2003 Standard Terminology of Advanced Ceramics
ASTM E 691 : 2019 : EDT 1 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 691 : 2023 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 3878 : 2016 Standard Terminology for Composite Materials
ASTM D 3878 : 2019 : REV A Standard Terminology for Composite Materials
ASTM D 3878 : 2020 : REV A Standard Terminology for Composite Materials
ASTM D 3878 : 1998 Standard Terminology Composite Materials
ASTM C 1239 : 2013 : R2018 Standard Practice for Reporting Uniaxial Strength Data and Estimating Weibull Distribution Parameters for Advanced Ceramics
ASTM D 3379 : 1975 : R1989 : EDT 1 Standard Test Method for Tensile Strength and Young's Modulus for High-Modulus Single-Filament Materials (Withdrawn 1998)
ASTM D 3878 : 2018 Standard Terminology for Composite Materials
ASTM E 691 : 2022 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E 1012 : 2012 : EDT 1 Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application
ASTM E 691 : 2009 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 3878 : 2002 Standard Terminology for Composite Materials
ASTM E 6 : 2015 : EDT 3 Standard Terminology Relating to Methods of Mechanical Testing
ASTM D 3878 : 2020 : REV B Standard Terminology for Composite Materials
ASTM C 1239 : 2000 Standard Practice for Reporting Uniaxial Strength Data and Estimating Weibull Distribution Parameters for Advanced Ceramics
ASTM E 6 : 2023 : REV A Standard Terminology Relating to Methods of Mechanical Testing
ASTM E 1012 : 2005 Standard Practice for Verification of Test Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application
ASTM C 1145 : 2006 : R2013 Standard Terminology of Advanced Ceramics
ASTM D 3878 : 2004 Standard Terminology for Composite Materials
ASTM C 1239 : 2000 : R2005 Standard Practice for Reporting Uniaxial Strength Data and Estimating Weibull Distribution Parameters for Advanced Ceramics
ASTM E 4 : 2021 Standard Practices for Force Calibration and Verification of Testing Machines
ASTM E 691 : 2021 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM C 1145 : 2002 Standard Terminology of Advanced Ceramics
ASTM D 3878 : 2007 : R2013 Standard Terminology for Composite Materials
ASTM D 3878 : 2020 : REDLINE Standard Terminology for Composite Materials
ASTM D 3878 : 2020 Standard Terminology for Composite Materials
ASTM D 3878 : 2003 Standard Terminology for Composite Materials
ASTM E 6 : 2015 : EDT 4 : REDLINE Standard Terminology Relating to Methods of Mechanical Testing
ASTM D 3878 : 2007 Standard Terminology for Composite Materials
ASTM C 1239 : 2006 Standard Practice for Reporting Uniaxial Strength Data and Estimating Weibull Distribution Parameters for Advanced Ceramics
ASTM C 1145 : 2002 : REV A Standard Terminology of Advanced Ceramics
ASTM E 6 : 2015 : EDT 4 Standard Terminology Relating to Methods of Mechanical Testing
ASTM E 6 : 2023 Standard Terminology Relating to Methods of Mechanical Testing
ASTM C 1145 : 2001 Standard Terminology of Advanced Ceramics
ASTM C 1239 : 2013 Standard Practice for Reporting Uniaxial Strength Data and Estimating Weibull Distribution Parameters for Advanced Ceramics
ASTM D 3878 : 2004 : REV A Standard Terminology for Composite Materials
ASTM C 1239 : 2007 Standard Practice for Reporting Uniaxial Strength Data and Estimating Weibull Distribution Parameters for Advanced Ceramics
ASTM C 1145 : 2006 : R2013 : EDT 1 Standard Terminology of Advanced Ceramics
ASTM E 1012 : 2019 Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application
ASTM D 3878 : 2001 Standard Terminology Composite Materials

View more information
US$90.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.