ASTM C 136 : 2006
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates
Available format(s)
Hardcopy , PDF
Superseded date
05-10-2023
Language(s)
English
Published date
02-15-2006
CONTAINED IN VOL. 04.02, 2014 Covers the determination of the particle size distribution of fine and coarse aggregates by sieving.
1.1 This test method covers the determination of the particle size distribution of fine and coarse aggregates by sieving.
1.2 Some specifications for aggregates which reference this test method contain grading requirements including both coarse and fine fractions. Instructions are included for sieve analysis of such aggregates.
1.3 The values stated in SI units are to be regarded as the standard. The values in parentheses are provided for information purposes only. Specification E 11 designates the size of sieve frames with inch units as standard, but in this test method the frame size is designated in SI units exactly equivalent to the inch units.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| Committee |
C 09
|
| DevelopmentNote |
Supersedes ASTM C 41, ASTM D 7, ASTM D 18 and ASTM D 19. (02/2002) Also numbered as AASHTO T 27. (05/2013)
|
| DocumentType |
Test Method
|
| Pages |
5
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM D 3744 : 2003 | Standard Test Method for Aggregate Durability Index |
| ASTM C 195 : 2007 : R2019 | Standard Specification for Mineral Fiber Thermal Insulating Cement |
| ASTM D 6913 : 2004 | Standard Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis |
| ASCE T&DI 58 10 : 2010 | STRUCTURAL DESIGN OF INTERLOCKING CONCRETE PAVEMENT FOR MUNICIPAL STREETS AND ROADWAYS |
| MIL-PRF-24667 Revision C:2008 | COATING SYSTEM, NON-SKID, FOR ROLL, SPRAY, OR SELF-ADHERING APPLICATION |
| ASTM D 6946 : 2003 | Standard Specification for Emulsified Refined Coal-Tar (Driveway Sealer, Ready to Use, Primarily Residential Grade) (Withdrawn 2012) |
| ASTM D 7521 : 2016 : REDLINE | Standard Test Method for Determination of Asbestos in Soil |
| ASTM F 735 : 2017 : REDLINE | Standard Test Method for Abrasion Resistance of Transparent Plastics and Coatings Using the Oscillating Sand Method |
| ASTM D 1139/D1139M : 2015 : REDLINE | Standard Specification for Aggregate for Single or Multiple Bituminous Surface Treatments |
| ASTM D 632 : 2012 | Standard Specification for Sodium Chloride |
| NSF 240:2017 | DRAINFIELD TRENCH PRODUCT SIZING FOR GRAVITY DISPERSAL ONSITE WASTEWATER TREATMENT AND DISPERSAL SYSTEMS |
| ASTM C 1093 : 2015-06 | PRACTICE FOR ACCREDITATION OF TESTING AGENCIES FOR MASONRY |
| ACI 211.1 : 1991 | SELECTING PROPORTIONS FOR NORMAL, HEAVYWEIGHT AND MASS CONCRETE |
| ASTM D 6783 : 2005 : R2011 | Standard Specification for Polymer Concrete Pipe |
| ASCE/EWRI 12-13, 13-13, 14-13 : 2013 | STANDARD GUIDELINES FOR THE DESIGN, INSTALLATION, AND OPERATION AND MAINTENANCE OF URBAN SUBSURFACE DRAINAGE |
| ASTM D 6783 : 2005 | Standard Specification for Polymer Concrete Pipe |
| ASTM C 1252 : 2017 | Standard Test Methods for Uncompacted Void Content of Fine Aggregate (as Influenced by Particle Shape, Surface Texture, and Grading) |
| ASTM C 404 : 2011 : R2017 | Standard Specification for Aggregates for Masonry Grout |
| ASTM D 3089 : 1997 : R2008 | Standard Practice for Determining the A-D Dimension of Aerosol Valve Dip Tubes |
| ASTM C 637 : 2014 : REDLINE | Standard Specification for Aggregates for Radiation-Shielding Concrete |
| ASTM D 1073 : 2016 : REDLINE | Standard Specification for Fine Aggregate for Asphalt Paving Mixtures |
| ASTM D 6270 : 2017 : REDLINE | Standard Practice for Use of Scrap Tires in Civil Engineering Applications |
| ASTM D 8038 : 2016 | Standard Practice for Reclamation of Recycled Aggregate Base (RAB) Material |
| ASTM D 693 : 2003 | Standard Specification for Crushed Aggregate for Macadam Pavements |
| ASTM D 7064/D7064M : 2008 : EDT 1 | Standard Practice for Open-Graded Friction Course (OGFC) Mix Design |
| ASTM D 692 : 2000 | Standard Specification for Coarse Aggregate for Bituminous Paving Mixtures |
| ASTM D 6928 : 2017 : REDLINE | Standard Test Method for Resistance of Coarse Aggregate to Degradation by Abrasion in the Micro-Deval Apparatus |
| ASME AG-1 : 2019 | CODE ON NUCLEAR AIR AND GAS TREATMENT |
| ASME AG 1 : 2012 | CODE ON NUCLEAR AIR AND GAS TREATMENT |
| ASTM D 692/D692M : 2015 : REDLINE | Standard Specification for Coarse Aggregate for Bituminous Paving Mixtures |
| ACI 211.3R : 2002 | GUIDE FOR SELECTING PROPORTIONS FOR NO-SLUMP CONCRETE |
| ASTM D 448 : 2012 : R2017 | Standard Classification for Sizes of Aggregate for Road and Bridge Construction |
| ASTM F 3016/F3016M : 2014 | Standard Test Method for Surrogate Testing of Vehicle Impact Protective Devices at Low Speeds |
| ASTM D 4223 : 1999 : R2006 | Standard Practice for Preparation of Test Specimens of Asphalt-Stabilized Soils |
| UFC 3-260-03 : 2001 | UNIFIED FACILITIES CRITERIA - AIRFIELD PAVEMENT EVALUATION |
| ASTM D 5821 : 2013 : R2017 | Standard Test Method for Determining the Percentage of Fractured Particles in Coarse Aggregate |
| ASTM D 7064/D7064M : 2008 | Standard Practice for Open-Graded Friction Course (OGFC) Mix Design |
| ASTM D 6932/D6932M : 2008 | Standard Guide for Materials and Construction of Open-Graded Friction Course Plant Mixtures |
| ASTM D 5106 : 2015 : REDLINE | Standard Specification for Steel Slag Aggregates for Bituminous Paving Mixtures |
| ASTM C 330 : 2005 | Standard Specification for Lightweight Aggregates for Structural Concrete |
| ASTM C 778 : 2017 : REDLINE | Standard Specification for Standard Sand |
| ACI 503.3M : 2010 | SPECIFICATION FOR PRODUCING A SKID-RESISTANT SURFACE ON CONCRETE BY THE USE OF EPOXY AND AGGREGATE - METRIC |
| ASTM D 345 : 2002 : R2010 | Standard Test Method for Sampling and Testing Calcium Chloride for Roads and Structural Applications (Withdrawn 2019) |
| ASTM D 995 : 1995 : REV B : R2002 | Standard Specification for Mixing Plants for Hot-Mixed, Hot-Laid Bituminous Paving Mixtures (Withdrawn 2009) |
| ASTM D 693 : 2003 : REV A | Standard Specification for Crushed Aggregate for Macadam Pavements (Withdrawn 2008) |
| ASTM C 1713 : 2017 : REDLINE | Standard Specification for Mortars for the Repair of Historic Masonry |
| ASTM D 4223 : 1999 | Standard Practice for Preparation of Test Specimens of Asphalt-Stabilized Soils |
| ASTM D 6913 : 2004 : R2009 : EDT 1 | Standard Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis |
| ASTM C 1747/C1747M : 2013 : REDLINE | Standard Test Method for Determining Potential Resistance to Degradation of Pervious Concrete by Impact and Abrasion |
| ASTM D 4215 : 2007 : R2013 | Standard Specification for Cold-Mixed, Cold-Laid Bituminous Paving Mixtures |
| ASTM D 1241 : 2015 : REDLINE | Standard Specification for Materials for Soil-Aggregate Subbase, Base, and Surface Courses |
| ASTM D 345 : 2002 | Standard Test Method for Sampling and Testing Calcium Chloride for Roads and Structural Applications |
| ASTM D 1557 : 2012 : EDT 1 | Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Modified Effort (56,000 ft-lbf/ft<sup>3</sup> (2,700 kN-m/m<sup>3</sup>)) |
| ASTM A 926 : 2003 | Standard Test Method for Comparing the Abrasion Resistance of Coating Materials for Corrugated Metal Pipe |
| ASTM C 1137 : 2005 | Standard Test Method for Degradation of Fine Aggregate Due to Attrition (Withdrawn 2011) |
| ASTM C 117 : 2017 : REDLINE | Standard Test Method for Materials Finer than 75-μm (No. 200) Sieve in Mineral Aggregates by Washing |
| ASTM A 926 : 2003 : R2014 | Standard Test Method for Comparing the Abrasion Resistance of Coating Materials for Corrugated Metal Pipe (Withdrawn 2016) |
| ASTM F 2223 : 2015 : REDLINE | GUIDE FOR ASTM STANDARDS ON PLAYGROUND SURFACING |
| ASTM C 35 : 2001 | Standard Specification for Inorganic Aggregates for Use in Gypsum Plaster |
| ASTM C 127 : 2015 : REDLINE | Standard Test Method for Relative Density (Specific Gravity) and Absorption of Coarse Aggregate |
| ASTM D 6945 : 2003 | Standard Specification for Emulsified Refined Coal-Tar (Ready to Use, Commercial Grade) |
| ASTM C 331 : 2005 | Standard Specification for Lightweight Aggregates for Concrete Masonry Units |
| ASTM D 7064 : 2004 | Standard Practice for Open-Graded Friction Course (OGFC) Mix Design |
| ASTM D 6932/D6932M : 2008 : R2013 | Standard Guide for Materials and Construction of Open-Graded Friction Course Plant Mixtures |
| ASTM D 345 : 2002 | Side bearings of the freight wagon bogies. General specifications |
| ASTM D 6460 : 2012 : REDLINE | Standard Test Method for Determination of Rolled Erosion Control Product (RECP) Performance in Protecting Earthen Channels from Stormwater-Induced Erosion |
| ASTM C 404 : 2011 | Standard Specification for Aggregates for Masonry Grout |
| UFC 3-250-03 : 2001 | UNIFIED FACILITIES CRITERIA - STANDARD PRACTICE MANUAL FOR FLEXIBLE PAVEMENTS |
| ASTM D 6913/D6913M : 2017 : REDLINE | Standard Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis |
| ASTM D 1863/D1863M : 2005 : R2011 : EDT 1 | Standard Specification for Mineral Aggregate Used on Built-Up Roofs |
| ASTM C 549 : 2006 | Standard Specification for Perlite Loose Fill Insulation |
| ASTM F 2075 : 2015 : REDLINE | Standard Specification for Engineered Wood Fiber for Use as a Playground Safety Surface Under and Around Playground Equipment |
| ASTM C 35 : 2001 : R2005 | Standard Specification for Inorganic Aggregates for Use in Gypsum Plaster |
| O-C-828 Revision C:1980 | CUPRIC SULFATE, PENTAHYDRATE, TECHNICAL |
| ASTM C 35 : 2001 : R2014 | Standard Specification for Inorganic Aggregates for Use in Gypsum Plaster |
| MIL-A-22262 Revision B:1993 | ABRASIVE BLASTING MEDIA SHIP HULL BLAST CLEANING |
| ASTM D 995 : 1995 : REV B | Standard Specification for Mixing Plants for Hot-Mixed, Hot-Laid Bituminous Paving Mixtures |
| ASTM D 4469 : 2017 : REDLINE | Standard Practice for Calculating Percent Asphalt Absorption by the Aggregate in Asphalt Mixtures |
| ASTM D 1074 : 2017 : REDLINE | Standard Test Method for Compressive Strength of Asphalt Mixtures |
| AASHTO M 194M/M 194 : 1900 | SPECIFICATION FOR CHEMICAL ADMIXTURES FOR CONCRETE |
| ACI PRC-363.2 : 2011 | GUIDE TO QUALITY CONTROL AND ASSURANCE OF HIGH-STRENGTH CONCRETE |
| ACI 533R : 2011 | GUIDE FOR PRECAST CONCRETE WALL PANELS |
| ACI 311.4R : 2005 | GUIDE FOR CONCRETE INSPECTION |
| ACI 503.3 : 2010 | SPECIFICATION FOR PRODUCING A SKID-RESISTANT SURFACE ON CONCRETE BY THE USE OF EPOXY AND AGGREGATE |
| ASTM D 7370/D7370M : 2014 : REDLINE | Standard Test Method for Determination of Relative Density and Absorption of Fine, Coarse and Blended Aggregate Using Combined Vacuum Saturation and Rapid Submersion |
| ASTM D 6945/D6945M : 2003 : R2017 | Standard Specification for Emulsified Refined Coal-Tar (Ready to Use, Commercial Grade) |
| AASHTO T 96 : 2002 | METHOD OF TEST FOR RESISTANCE TO DEGRADATION OF SMALL-SIZE COARSE AGGREGATE BY ABRASION AND IMPACT IN THE LOS ANGELES MACHINE |
| AASHTO T 96:2002(R2019) | Standard Method of Test for Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine |
| ASTM F 1128 : 1988 | Test Method for Abrasion Resistance of Transparent Plastics and Coatings Using Salt Impingement Method (Withdrawn 1996) |
| ASTM D 7064/D7064M : 2008 : R2013 | Standard Practice for Open-Graded Friction Course (OGFC) Mix Design |
| ASTM C 195 : 2007 : R2013 | Standard Specification for Mineral Fiber Thermal Insulating Cement |
| ASTM D 6913 : 2004 : R2009 | Standard Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis |
| ASTM F 3012 : 2014 | Standard Specification for Loose-Fill Rubber for Use as a Playground Safety Surface under and around Playground Equipment |
| ASTM D 6913 : 2004 : EDT 2 | Standard Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis |
| ASTM D 3042 : 2017 : REDLINE | Standard Test Method for Insoluble Residue in Carbonate Aggregates |
| ASTM D 6783 : 2005 : REV A : R2017 | Standard Specification for Polymer Concrete Pipe |
| ASTM D 7428 : 2015 : REDLINE | Standard Test Method for Resistance of Fine Aggregate to Degradation by Abrasion in the Micro-Deval Apparatus |
| ASTM C 331/C331M : 2017 : REDLINE | Standard Specification for Lightweight Aggregates for Concrete Masonry Units |
| CSA A23.1 A23.2 : 2014 | CONCRETE MATERIALS AND METHODS OF CONCRETE CONSTRUCTION/TEST METHODS AND STANDARD PRACTICES FOR CONCRETE |
| IEEE 81-2012 | IEEE Guide for Measuring Earth Resistivity, Ground Impedance, and Earth Surface Potentials of a Grounding System |
| ASTM D 5711 : 2003 | Standard Test Method for Determining the Adherent Coating on Coarse Aggregates (Withdrawn 2012) |
| SSPC-PA GUIDE 13 : 2006 | GUIDE SPECIFICATION FOR APPLICATION OF COATING SYSTEMS WITH ZINC-RICH PRIMERS TO STEEL BRIDGES |
| SAE AMS 2518:2010(S2012) | THREAD COMPOUND, ANTI-SEIZE, GRAPHITE-PETROLATUM |
| ASTM D 698 : 2013-05 | TEST METHODS FOR LABORATORY COMPACTION CHARACTERISTICS OF SOIL USING STANDARD EFFORT (12400 FT-LBF/FT[3] (600 KN-M/M[3])) |
| ASTM C 35 : 2001 : R2009 | Standard Specification for Inorganic Aggregates for Use in Gypsum Plaster |
| ASTM D 448 :2012 | Standard Classification for Sizes of Aggregate for Road and Bridge Construction |
| ASTM D 2940/D2940M : 2015 : REDLINE | Standard Specification for Graded Aggregate Material For Bases or Subbases for Highways or Airports |
| ASTM D 692 : 2000 : R2004 | Standard Specification for Coarse Aggregate for Bituminous Paving Mixtures |
| ASTM D 5821 : 2013 | Standard Test Method for Determining the Percentage of Fractured Particles in Coarse Aggregate |
| ASTM D 995 : 1995 | Standard Specification for Mixing Plants for Hot-Mixed, Hot-Laid Bituminous Paving Mixtures |
| ACI 221R : 1996 | GUIDE FOR USE OF NORMAL WEIGHT AND HEAVYWEIGHT AGGREGATES IN CONCRETE |
| ASTM C 516 : 2008 : R2013 : EDT 1 | Standard Specification for Vermiculite Loose Fill Thermal Insulation |
| ACI 311.5R : 2004 | GUIDE FOR CONCRETE PLANT INSPECTION AND TESTING OF READY-MIXED CONCRETE |
| ASTM C 144 : 2018 : REDLINE | Standard Specification for Aggregate for Masonry Mortar |
| ASTM D 2487 : 2017 : REDLINE | Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System) |
| ASTM E 2788 : 2011 | Standard Specification for Use of Expanded Shale, Clay and Slate (ESCS) as a Mineral Component in the Growing Media and the Drainage Layer for Vegetative (Green) Roof Systems |
| ASTM A 926 : 2003 : R2008 | Standard Test Method for Comparing the Abrasion Resistance of Coating Materials for Corrugated Metal Pipe |
| ASTM D 4223/D4223M : 2012 | Standard Practice for Preparation of Test Specimens of Asphalt-Stabilized Soils |
| ASTM C 802 : 2014 : REDLINE | Standard Practice for Conducting an Interlaboratory Test Program to Determine the Precision of Test Methods for Construction Materials |
| ASTM D 2940 : 2003 | Standard Specification for Graded Aggregate Material For Bases or Subbases for Highways or Airports |
| ASTM D 1557 : 2012 | Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Modified Effort (56,000 ft-lbf/ft<sup>3</sup> (2,700 kN-m/m<sup>3</sup>)) |
| NSF 50 : 2016 | EQUIPMENT FOR SWIMMING POOLS, SPAS, HOT TUBS AND OTHER RECREATIONAL WATER FACILITIES |
| ASTM D 1139 : 2000 | Standard Specification for Aggregate for Single or Multiple Bituminous Surface Treatments |
| ACI 207.5R : 2011 | REPORT ON ROLLER-COMPACTED MASS CONCRETE |
| ASTM D 1863 : 2005 | Standard Specification for Mineral Aggregate Used on Built-Up Roofs |
| ACI ITG-4.2R : 2006 | MATERIALS AND QUALITY CONSIDERATIONS FOR HIGH-STRENGTH CONCRETE IN MODERATE TO HIGH SEISMIC APPLICATIONS |
| MIL-S-17726 Revision C:1980 | SAND SANDBLAST |
| AWWA B102:2015 | MANGANESE GREENSAND FOR FILTERS |
| ACI 548.2R : 93(R1998) | GUIDE FOR MIXING AND PLACING SULFUR CONCRETE IN CONSTRUCTION |
| ASTM C 516 : 2008 | Standard Specification for Vermiculite Loose Fill Thermal Insulation |
| ACI 363R : 2010 | REPORT ON HIGH-STRENGTH CONCRETE |
| ASTM C 195 : 2007 | Standard Specification for Mineral Fiber Thermal Insulating Cement |
| ASTM D 1139 : 2000 : R2004 | Standard Specification for Aggregate for Single or Multiple Bituminous Surface Treatments |
| UFC 3-280-04 : 2003 | UNIFIED FACILITIES CRITERIA - ARMY FILTRATION OF LIQUIDS |
| SAE AMS 1448 : 2014 | SAND, AIRPORT SNOW AND ICE CONTROL |
| ACI 345R : 2011 | GUIDE FOR CONCRETE HIGHWAY BRIDGE DECK CONSTRUCTION |
| ASTM D 2172 : 2005 | Standard Test Methods for Quantitative Extraction of Bitumen From Bituminous Paving Mixtures |
| ASTM D 6155 : 2015 | Standard Specification for Nontraditional Coarse Aggregates for Bituminous Paving Mixtures |
| ASTM C 88 : 2013-08 | TEST METHOD FOR SOUNDNESS OF AGGREGATES BY USE OF SODIUM SULFATE OR MAGNESIUM SULFATE |
| ASTM C 685/C685M : 2017 : REDLINE | Standard Specification for Concrete Made by Volumetric Batching and Continuous Mixing |
| ASTM D 4215 : 2007 | Standard Specification for Cold-Mixed, Cold-Laid Bituminous Paving Mixtures |
| ASTM D 3515 : 2001 | Standard Specification for Hot-Mixed, Hot-Laid Bituminous Paving Mixtures (Withdrawn 2009) |
| ASTM D 6913 : 2004 : EDT 1 | Standard Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis |
| ASTM D 5519 : 2015 : REDLINE | Standard Test Methods for Particle Size Analysis of Natural and Man-Made Riprap Materials |
| ASTM C 549 : 2006 : R2012 | Standard Specification for Perlite Loose Fill Insulation |
| ASTM C 897 : 2015 : REDLINE | Standard Specification for Aggregate for Job-Mixed Portland Cement-Based Plasters |
| ASTM C 131/C131M : 2014 : REDLINE | Standard Test Method for Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine |
| ASTM D 7564/D7564M : 2016 : REDLINE | Standard Practice for Construction of Asphalt-Rubber Cape Seal |
| ASTM D 5624 : 2013 : REDLINE | Standard Practice for Determining the Transverse-Aggregate Spread Rate for Surface Treatment Applications |
| ASTM D 6945/D6945M : 2003 : R2011 : EDT 1 | Standard Specification for Emulsified Refined Coal-Tar (Ready to Use, Commercial Grade) |
| SSPC-AB 3:2017(R2023) | Ferrous Metallic Abrasive |
| ASTM D 75 : 2003 | Standard Practice for Sampling Aggregates |
| ASTM C 702 : 1998 | Standard Practice for Reducing Samples of Aggregate to Testing Size |
| ASTM C 637 : 2014 : REDLINE | Standard Specification for Aggregates for Radiation-Shielding Concrete |
| ASTM E 11 : 2017 : REDLINE | Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves |
| ASTM C 117 : 2017 : REDLINE | Standard Test Method for Materials Finer than 75-μm (No. 200) Sieve in Mineral Aggregates by Washing |
| ASTM C 670 : 2015 : REDLINE | Standard Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials |
US$75.00
Excluding Tax where applicable
USD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.