• There are no items in your cart

ASTM C 1366 : 2004 : R2013

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Tensile Strength of Monolithic Advanced Ceramics at Elevated Temperatures
Available format(s)

Hardcopy , PDF

Superseded date

09-16-2019

Language(s)

English

Published date

08-01-2013

CONTAINED IN VOL. 15.01, 2018 Includes determination of tensile strength under uniaxial loading of monolithic advanced ceramics at elevated temperatures.

1.1This test method covers the determination of tensile strength under uniaxial loading of monolithic advanced ceramics at elevated temperatures. This test method addresses, but is not restricted to, various suggested test specimen geometries as listed in the appendix. In addition, test specimen fabrication methods, testing modes (force, displacement, or strain control), testing rates (force rate, stress rate, displacement rate, or strain rate), allowable bending, and data collection and reporting procedures are addressed. Tensile strength as used in this test method refers to the tensile strength obtained under uniaxial loading.

1.2This test method applies primarily to advanced ceramics which macroscopically exhibit isotropic, homogeneous, continuous behavior. While this test method applies primarily to monolithic advanced ceramics, certain whisker, or particle-reinforced composite ceramics as well as certain discontinuous fiber-reinforced composite ceramics may also meet these macroscopic behavior assumptions. Generally, continuous fiber ceramic composites (CFCCs) do not macroscopically exhibit isotropic, homogeneous, continuous behavior and application of this test method to these materials is not recommended.

1.3The values stated in SI units are to be regarded as the standard and are in accordance with Practice E380.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Refer to Section 7 for specific precautions.

Committee
C 28
DocumentType
Test Method
Pages
27
ProductNote
Reconfirmed 2013
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM C 1683 : 2010 : R2019 Standard Practice for Size Scaling of Tensile Strengths Using Weibull Statistics for Advanced Ceramics

ASTM C 1145 : 2019 Standard Terminology of Advanced Ceramics
ASTM E 380 : 1993 Standard Practice for Use of the Internation System of Units (SI) (the Modernized Metric System) (Withdrawn 1997)
ASTM E 1012 : 2014 Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application
ASTM C 1322 : 2005 : REV B Standard Practice for Fractography and Characterization of Fracture Origins in Advanced Ceramics
ASTM C 1145 : 1998 Standard Terminology of Advanced Ceramics
ASTM C 1161 : 2002 : REV C : R2008 Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature
ASTM C 1145 : 2006 Standard Terminology of Advanced Ceramics
ASTM C 1161 : 2002 : REV C : R2008 : EDT 1 Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature
ASTM C 1322 : 2015 Standard Practice for Fractography and Characterization of Fracture Origins in Advanced Ceramics
ASTM C 1322 : 2005 : REV A Standard Practice for Fractography and Characterization of Fracture Origins in Advanced Ceramics
ASTM C 1145 : 2005 Standard Terminology of Advanced Ceramics
ASTM C 1161 : 2002 : REV C : EDT 1 Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature
ASTM E 1012 : 1999 Standard Practice for Verification of Specimen Alignment Under Tensile Loading
ASTM E 1012 : 2012 Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application
ASTM C 1322 : 2005 : REV B : EDT 1 Standard Practice for Fractography and Characterization of Fracture Origins in Advanced Ceramics
ASTM E 83 : 2016 : REDLINE Standard Practice for Verification and Classification of Extensometer Systems
ASTM C 1161 : 2002 : REV A Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature
ASTM E 1012 : 2014 : EDT 1 Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application
ASTM C 1239 : 2006 : REV A Standard Practice for Reporting Uniaxial Strength Data and Estimating Weibull Distribution Parameters for Advanced Ceramics
ASTM C 1145 : 2003 Standard Terminology of Advanced Ceramics
IEEE/ASTM SI_10-2010 American National Standard for Metric Practice
ASTM C 1239 : 2013 : R2018 Standard Practice for Reporting Uniaxial Strength Data and Estimating Weibull Distribution Parameters for Advanced Ceramics
ASTM C 1322 : 2005 : REV B : R2010 Standard Practice for Fractography and Characterization of Fracture Origins in Advanced Ceramics
ASTM C 1322 : 1996 : REV A Standard Practice for Fractography and Characterization of Fracture Origins in Advanced Ceramics
ASTM D 3379 : 1975 : R1989 : EDT 1 Standard Test Method for Tensile Strength and Young's Modulus for High-Modulus Single-Filament Materials (Withdrawn 1998)
ASTM C 1161 : 2018 Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature
ASTM C 1322 : 2015 : REDLINE PRACTICE FOR FRACTOGRAPHY AND CHARACTERIZATION OF FRACTURE ORIGINS IN ADVANCED CERAMICS
ASTM E 1012 : 2012 : EDT 1 Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application
ASTM C 1161 : 2002 Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature
ASTM C 1322 : 2002 Standard Practice for Fractography and Characterization of Fracture Origins in Advanced Ceramics
ASTM C 1239 : 2000 Standard Practice for Reporting Uniaxial Strength Data and Estimating Weibull Distribution Parameters for Advanced Ceramics
ASTM E 1012 : 2005 Standard Practice for Verification of Test Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application
ASTM C 1145 : 2006 : R2013 Standard Terminology of Advanced Ceramics
ASTM E 337 : 2015 : REDLINE Standard Test Method for Measuring Humidity with a Psychrometer (the Measurement of Wet- and Dry-Bulb Temperatures)
ASTM C 1161 : 2013 Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature
ASTM C 1239 : 2000 : R2005 Standard Practice for Reporting Uniaxial Strength Data and Estimating Weibull Distribution Parameters for Advanced Ceramics
ASTM C 1322 : 2002 : REV A Standard Practice for Fractography and Characterization of Fracture Origins in Advanced Ceramics
ASTM E 220 : 2013 : REDLINE Standard Test Method for Calibration of Thermocouples By Comparison Techniques
ASTM C 1145 : 2002 Standard Terminology of Advanced Ceramics
ASTM D 3379 : 1975 TEST METHOD FOR TENSILE STRENGTH AND YOUNG'S MODULUS FOR HIGH-MODULUS SINGLE-FILAMENT MATERIALS
ASTM C 1161 : 1994 : R1996 Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature
ASTM C 1239 : 2006 Standard Practice for Reporting Uniaxial Strength Data and Estimating Weibull Distribution Parameters for Advanced Ceramics
ASTM C 1145 : 2002 : REV A Standard Terminology of Advanced Ceramics
ASTM C 1161 : 2002 : REV C Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature
ASTM C 1322 : 2005 Standard Practice for Fractography and Characterization of Fracture Origins in Advanced Ceramics
ASTM C 1145 : 2001 Standard Terminology of Advanced Ceramics
ASTM C 1239 : 2013 Standard Practice for Reporting Uniaxial Strength Data and Estimating Weibull Distribution Parameters for Advanced Ceramics
ASTM C 1239 : 2007 Standard Practice for Reporting Uniaxial Strength Data and Estimating Weibull Distribution Parameters for Advanced Ceramics
ASTM C 1145 : 2006 : R2013 : EDT 1 Standard Terminology of Advanced Ceramics
ASTM C 1161 : 2002 : REV B Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature

View more information
US$108.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.