ASTM C 595/C595M : 2020
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Specification for Blended Hydraulic Cements
Hardcopy , PDF
08-03-2023
English
04-22-2020
1.1This specification pertains to blended hydraulic cements for both general and special applications, using slag, pozzolan, limestone, or some combination of these, with portland cement or portland cement clinker or slag with lime.
Note 1:This specification prescribes ingredients and proportions, with some performance requirements, whereas Performance Specification C1157/C1157M is a hydraulic cement specification in which performance criteria alone govern the products and their acceptance.
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Values in SI units [or inch-pound units] shall be obtained by measurement in SI units [or inch-pound units] or by appropriate conversion, using the Rules for Conversion and Rounding given in IEEE/ASTM SI 10, of measurements made in other units [or SI units]. Values are stated in only SI units when inch-pound units are not used in practice.
1.3The text of this specification refers to notes and footnotes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) are not requirements of the standard.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Committee |
C 01
|
| DocumentType |
Standard
|
| Pages |
8
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM C 1157/C1157M : 2020 : REV A | Standard Performance Specification for Hydraulic Cement |
| ASTM C 412M : 2019 | Standard Specification for Concrete Drain Tile (Metric) |
| ASTM C 1577 : 2020 | Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers Designed According to AASHTO LRFD |
| ASTM C 1491 : 2019 | Standard Specification for Concrete Roof Pavers (Withdrawn 2023) |
| ASTM C 1731 : 2021 | Standard Specification for Concrete Floor Tile |
| ASTM C 1222 : 2021 | Standard Practice for Evaluation of Laboratories Testing Hydraulic Cement |
| ASTM C 1634 : 2020 | Standard Specification for Concrete Facing Brick and Other Concrete Masonry Facing Units |
| ASTM C 935 : 2019 | Standard Specification for General Requirements for Prestressed Concrete Poles Statically Cast |
| ASTM C 465 : 2019 | Standard Specification for Processing Additions for Use in the Manufacture<brk/> of Hydraulic Cements |
| ASTM C 1504M : 2020 | Standard Specification for Manufacture of Precast Reinforced Concrete Three-Sided Structures for Culverts and Storm Drains (Metric) |
| ASTM C 219 : 2020 : REV A | Standard Terminology Relating to Hydraulic and Other Inorganic Cements |
| ASTM D 6684 : 2018 | Standard Specification for Materials and Manufacture of Articulating Concrete Block (ACB) Systems |
| ASTM C 1417 : 2019 | Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design |
| ASTM C 1433 : 2020 | Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers |
| ASTM C 412 : 2019 | Standard Specification for Concrete Drain Tile |
| ASTM C 1804 : 2020 | Standard Specification for Spun Cast Prestressed Concrete Bases for Tapered Steel Lighting Poles |
| ASTM A 1105 : 2017 | Standard Specification for Corrugated Steel Manhole Assemblies |
| ASTM C 476 : 2020 | Standard Specification for Grout for Masonry |
| ASTM C 76 : 2020 | Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe |
| ASTM C 506 : 2020 : EDT 1 | Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe |
| ASTM C 655 : 2019 : REV A | Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe |
| ASTM C 507M : 2020 | Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe (Metric) |
| ASTM C 185 : 2020 | Standard Test Method for Air Content of Hydraulic Cement Mortar |
| ASTM C 1786 : 2019 | Standard Specification for Segmental Precast Reinforced Concrete Box Sections for Culverts, Storm Drains, and Sewers Designed According to AASHTO LRFD |
| ASTM C 1818 : 2019 | Standard Specification for Synthetic Fiber Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe |
| ASTM C 1884 : 2019 | Standard Specification for Concrete Ballast Block |
| ASTM C 1782/C1782M : 2020 : REV A | Standard Specification for Segmental Concrete Paving Slabs |
| ASTM C 1904 : 2020 | Standard Test Methods for Determination of the Effects of Biogenic Acidification on Concrete Antimicrobial Additives and/or Concrete Products |
| ASTM D 560/D560M : 2016 | Standard Test Methods for Freezing and Thawing Compacted Soil-Cement Mixtures |
| ASTM C 1089 : 2019 | Standard Specification for Spun Cast Prestressed Concrete Poles |
| ASTM C 985 : 2019 | Standard Specification for Nonreinforced Concrete Specified Strength Culvert, Storm Drain, and Sewer Pipe |
| ASTM C 183/C183M : 2016 | Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement |
| ASTM C 226 : 2019 | Standard Specification for Air-Entraining Additions for Use in the Manufacture of Air-Entraining Hydraulic Cement |
| ASTM C 887 : 2020 | Standard Specification for Packaged, Dry, Combined Materials for Surface Bonding Mortar |
| ASTM C 76M : 2020 | Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe (Metric) |
| ASTM C 563 : 2020 | Standard Guide for Approximation of Optimum SO<inf>3</inf> in Hydraulic Cement |
| ASTM C 1449/C1449M : 2005 : REV A : R2019 | Standard Specification for Non-Asbestos Fiber-Cement Nonpressure Sewer Pipe |
| ASTM E 2277 : 2014(R2019) | Standard Guide for Design and Construction of Coal Ash Structural Fills |
| ASTM C 1670/C1670M : 2021 : REV A | Standard Specification for Adhered Manufactured Stone Masonry Veneer Units |
| ASTM C 1846/C1846M : 2019 | Standard Specification for Performance Based Manufacture of Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe |
| ASTM C 1776/C1776M : 2017 | Standard Specification for Wet-Cast Precast Modular Retaining Wall Units |
| ASTM C 1227 : 2020 | Standard Specification for Precast Concrete Septic Tanks |
| ASTM C 118 : 2019 | Standard Specification for Concrete Pipe for Irrigation or Drainage |
| ASTM C 1707 : 2018 | Standard Specification for Pozzolanic Hydraulic Lime for Structural Purposes |
| ASTM C 1688/C1688M : 2014 : REV A | Standard Test Method for Density and Void Content of Freshly Mixed Pervious Concrete (Withdrawn 2023) |
| ASTM C 858 : 2019 | Standard Specification for Underground Precast Concrete Utility Structures |
| ASTM C 913 : 2018 | Standard Specification for Precast Concrete Water and Wastewater Structures |
| ASTM C 118M : 2019 | Standard Specification for Concrete Pipe for Irrigation or Drainage (Metric) (Withdrawn 2024) |
| ASTM C 654 : 2019 | Standard Specification for Porous Concrete Pipe |
| ASTM C 989/C989M : 2018 : REV A | Standard Specification for Slag Cement for Use in Concrete and Mortars |
| ASTM C 1417M : 2019 | Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design (Metric) |
| ASTM C 1012/C1012M : 2018 : REV B | Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution |
| ASTM C 109/C109M : 2020 : REV B | Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50mm] Cube Specimens) |
| ASTM C 1693 : 2011 : R2017 | Standard Specification for Autoclaved Aerated Concrete (AAC) |
| ASTM C 1448/C1448M : 2005 : R2019 | Standard Specification for Non-Asbestos Fiber-Cement Conduit |
| ASTM C 926 : 2020 : REV B | Standard Specification for Application of Portland Cement-Based Plaster |
| ASTM C 655M : 2019 : REV A | Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe (Metric) |
| ASTM C 685/C685M : 2017 | Standard Specification for Concrete Made by Volumetric Batching and Continuous Mixing |
| ASTM C 505M : 2019 | Standard Specification for Nonreinforced Concrete Irrigation Pipe With Rubber Gasket Joints (Metric) |
| ASTM C 505 : 2019 | Standard Specification for Nonreinforced Concrete Irrigation Pipe with Rubber Gasket Joints |
| ASTM C 1504 : 2020 | Standard Specification for Manufacture of Precast Reinforced Concrete Three-Sided Structures for Culverts and Storm Drains |
| ASTM C 361 : 2019 : REV A | Standard Specification for Reinforced Concrete Low-Head Pressure Pipe |
| ASTM C 936/C936M : 2021 | Standard Specification for Solid Concrete Interlocking Paving Units |
| ASTM C 14 : 2020 | Standard Specification for Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe |
| ASTM C 1450/C1450M : 2004 : R2019 | Standard Specification for Non-Asbestos Fiber-Cement Storm Drain Pipe |
| ASTM C 1765 : 2019 | Standard Specification for Steel Fiber Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe |
| ASTM C 90 : 2016 : REV A | Standard Specification for Loadbearing Concrete Masonry Units |
| ASTM C 1903 : 2021 | Standard Specification for Precast Concrete Duct Bank |
| ASTM C 654M : 2019 | Standard Specification for Porous Concrete Pipe (Metric) |
| ASTM C 1447/C1447M : 2004 : R2019 | Standard Specification for Non-Asbestos Fiber-Cement Underdrain Pipe |
| ASTM C 1433M : 2020 | Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers (Metric) |
| ASTM C 1837 : 2017 | Standard Specification for Production of Dry Cast Concrete Used for Manufacturing Pipe, Box, and Precast Structures |
| ASTM C 915 : 1979 : R2018 | Standard Specification for Precast Reinforced Concrete Crib Wall Members |
| ASTM C 507 : 2020 | Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe |
| ASTM C 14M : 2020 | Standard Specification for Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe (Metric) |
| ASTM C 1581/C1581M : 2018 : REV A | Standard Test Method for Determining Age at Cracking and Induced Tensile Stress Characteristics of Mortar and Concrete under Restrained Shrinkage |
| ASTM C 506M : 2020 | Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe (Metric) |
| ASTM D 5759 : 2012 : R2020 | Standard Guide for Characterization of Coal Fly Ash and Clean Coal Combustion Fly Ash for Potential Uses |
| ASTM C 1157/C1157M : 2020 | Standard Performance Specification for Hydraulic Cement |
| ASTM C 1157/C1157M : 2020 : REV A | Standard Performance Specification for Hydraulic Cement |
| ASTM C 1778 : 2019 : REV B | Standard Guide for Reducing the Risk of Deleterious Alkali-Aggregate Reaction in Concrete |
| ASTM C 226 : 1996 | Standard Specification for Air-Entraining Additions for Use in the Manufacture of Air-Entraining Hydraulic Cement |
| ASTM C 114 : 2009 | Standard Test Methods for Chemical Analysis of Hydraulic Cement |
| ASTM C 51 : 2001 | Standard Terminology Relating to Lime and Limestone (as used by the Industry) |
| ASTM C 51 : 2021 | Standard Terminology Relating to Lime and Limestone (as Used by the Industry) |
| ASTM C 1778 : 2020 | Standard Guide for Reducing the Risk of Deleterious Alkali-Aggregate Reaction in Concrete |
| ASTM C 1702 : 2009 | Standard Test Method for Measurement of Heat of Hydration of Hydraulic Cementitious Materials Using Isothermal Conduction Calorimetry |
| ASTM C 563 : 2018 : REV A | Standard Guide for Approximation of Optimum SO<inf>3</inf> in Hydraulic Cement |
| ASTM C 51 : 2020 | Standard Terminology Relating to Lime and Limestone (as Used by the Industry) |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.