• There are no items in your cart

ASTM C 647 : 2008 : R2013

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Guide to Properties and Tests of Mastics and Coating Finishes for Thermal Insulation
Available format(s)

Hardcopy , PDF

Superseded date

04-12-2019

Language(s)

English

Published date

11-01-2013

CONTAINED IN VOL. 04.06, 2014 Describes properties of mastics and coating finishes characterizing their performance as finishes for thermal insulation.

1.1This guide identifies properties of mastics and coating finishes characterizing their performance as finishes for thermal insulation.

1.2These properties relate to application and service. Each property is defined, and its significance and suggested test methods are described.

1.3The properties appear in the following order in this guide.

Paragraph

Application Properties

6

Consistency

6.1

Coverage

6.2

Build

6.3

Wet Flammability

6.4

Toxicity

6.5

Temperature and Humidity Range

6.6

Surface Wetting and Adhesion

6.7

Gap Filling and Bridging

6.8

Sizing and Sealing

6.9

Corrosion or Solvent Attack

6.10

Drying Time and Curing Time

6.11

Shrinkage

6.12

Storage Stability

6.13

Freeze-Thaw Stability

6.14

Service Properties

7

Specimen Preparation

7.1

Outdoor Durability

7.2

Environmental Resistance

7.3

  Temperature Limits

7.3.1

  Chemicals and Water Resistance

7.3.2

  Mold and Mildew Resistance

7.3.3

Surface Flammability

7.4

Water-Vapor Transmission Rate

7.5

Adhesion

7.6

Damage Resistance

7.7

  Impact Resistance

7.7.1

  Abrasion Resistance

7.7.2

Stress Resistance

7.8

  Flexure

7.8.1

  Elongation

7.8.2

Color

7.9

Odor

7.10

Other Properties

8


1.4The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Committee
C 16
DocumentType
Guide
Pages
6
ProductNote
Reconfirmed 2013
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM E 96/E96M : 2016 : REDLINE Standard Test Methods for Water Vapor Transmission of Materials
ASTM D 529 : 2004 Standard Practice for Enclosed Carbon-Arc Exposures of Bituminous Materials (Withdrawn 2013)
ASTM D 1729 : 2016 : REDLINE Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials
ASTM C 639 : 2015 : REDLINE Standard Test Method for Rheological (Flow) Properties of Elastomeric Sealants
ASTM G 21 : 2015 : REDLINE Standard Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi
ASTM D 2354 : 2010 Standard Test Method for Minimum Film Formation Temperature (MFFT) of Emulsion Vehicles
ASTM D 543 : 2014 : REDLINE Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
ASTM D 1310 : 2014 : REDLINE Standard Test Method for Flash Point and Fire Point of Liquids by Tag Open-Cup Apparatus
ASTM D 562 : 2010 Standard Test Method for Consistency of Paints Measuring Krebs Unit (KU) Viscosity Using a Stormer-Type Viscometer
ASTM D 2939 : 2003 Standard Test Methods for Emulsified Bitumens Used as Protective Coatings (Withdrawn 2012)
ASTM D 3134 : 2015 : REDLINE Standard Practice for Establishing Color and Gloss Tolerances
ASTM D 2444 : 1999 Standard Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
ASTM D 2453 : 2015 : REDLINE Standard Test Method for Shrinkage and Tenacity of Oil- and Resin-Base Caulking Compounds
ASTM D 790 : 2017 : REDLINE Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
ASTM D 93 : 2016-07 TEST METHODS FOR FLASH POINT BY PENSKY-MARTENS CLOSED CUP TESTER
ASTM C 792 : 2015 : REDLINE Standard Test Method for Effects of Heat Aging on Weight Loss, Cracking, and Chalking of Elastomeric Sealants
ASTM C 488 : 2016 : REDLINE Standard Test Method for Conducting Exterior Exposure Tests of Finishes for Thermal Insulation
ASTM G 23 : 1996 Practice for Operating Light-Exposure Apparatus (Carbon-Arc Type) With and Without Water for Exposure of Nonmetallic Materials (Withdrawn 2000)
ASTM D 1823 : 2016 : REDLINE Standard Test Method for Apparent Viscosity of Plastisols and Organosols at High Shear Rates by Extrusion Viscometer
ASTM D 658 : 1991 Standard Test Method for Abrasion Resistance of Organic Coatings by Air Blast Abrasive (Withdrawn 1996)
ASTM E 659 : 2015 : REDLINE Standard Test Method for Autoignition Temperature of Chemicals
ASTM C 733 : 1993 Standard Test Method for Volume Shrinkage of Latex Sealants (Withdrawn 2000)
ASTM D 1824 : 2016 : REDLINE Standard Test Method for Apparent Viscosity of Plastisols and Organosols at Low Shear Rates
ASTM E 162 : 2016 : REDLINE Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source
ASTM D 638 : 2014 : REDLINE Standard Test Method for Tensile Properties of Plastics
ASTM C 461 : 2017 : REDLINE Standard Test Methods for Mastics and Coatings Used With Thermal Insulation
ASTM C 168 : 2017-06 TERMINOLOGY RELATING TO THERMAL INSULATION

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.