ASTM C 898/C898M : 2009 : R2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
04-08-2024
English
12-14-2017
CONTAINED IN VOL. 06.03, 2017 Specifies the use of a high solids content, cold liquid-applied elastomeric waterproofing membrane that meets the criteria in Specification C 836, in a waterproofing system subject to hydrostatic pressure for building decks over occupied space where the membrane is covered with a separate protective wearing course.
1.1This guide describes the use of a high solids content, cold liquid-applied elastomeric waterproofing membrane that meets the criteria in Specification C836/C836M, in a waterproofing system subject to hydrostatic pressure for building decks over occupied space where the membrane is covered with a separate protective wearing course.
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Committee |
D 08
|
| DevelopmentNote |
Supersedes ASTM C 898. (07/2009)
|
| DocumentType |
Guide
|
| Pages |
14
|
| ProductNote |
Reconfirmed 2017
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM D 7492/D7492M : 2016 : REV A : R2024 | Standard Guide for Use of Drainage System Media with Waterproofing Systems |
| ASTM D 8463/D8463M : 2023 | Standard Specification for High Solids Content, Cold Liquid-Applied Elastomeric, Silyl-Terminated Polymer Based Waterproofing Membrane for Use with Separate Wearing Course |
| ASTM E 2266 : 2022 | Standard Guide for Design and Construction of Low-Rise Frame Building Wall Systems to Resist Water Intrusion |
| ASTM D 1752 : 1967 | Standard Specifications For Preformed Expansion Joint Fillers For Concrete Paving And Structural Construction1 Nonextruding And Resilient Nonbituminous Types |
| ACI 301 : 2016 | SPECIFICATIONS FOR STRUCTURAL CONCRETE |
| ASTM C 1193 : 2011 : REV A | Standard Guide for Use of Joint Sealants |
| ASTM D 1751 : 2004 : R2013 : EDT 1 | Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Bituminous Types) |
| ASTM C 1471/C1471M : 2005 : R2014 : EDT 1 | Standard Guide for the Use of High Solids Content Cold Liquid-Applied Elastomeric Waterproofing Membrane on Vertical Surfaces |
| ASTM D 5295 : 2000 | Standard Guide for Preparation of Concrete Surfaces for Adhered (Bonded) Membrane Waterproofing Systems |
| ASTM C 33/C33M : 2023 | Standard Specification for Concrete Aggregates |
| ASTM C 1193 : 2016 : R2023 | Standard Guide for Use of Joint Sealants |
| ASTM D 1056 : 2007 | Standard Specification for Flexible Cellular Materials—Sponge or Expanded Rubber |
| ASTM C 1472 : 2016 : REDLINE | Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width |
| ASTM C 1472 : 2005 | Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width |
| ASTM C 1193 : 2016 | Standard Guide for Use of Joint Sealants |
| ASTM D 1752 : 2004 | Standard Specification for Preformed Sponge Rubber and Cork Expansion Joint Fillers for Concrete Paving and Structural Construction |
| ASTM C 33/C33M : 2018 | Standard Specification for Concrete Aggregates |
| ASTM C 1472 : 2010 | Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width |
| ASTM D 1752 : 2004 : REV A : R2013 | Standard Specification for Preformed Sponge Rubber Cork and Recycled PVC Expansion Joint Fillers for Concrete Paving and Structural Construction |
| ASTM D 1751 : 1999 | Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Bituminous Types) |
| ASTM C 836/C836M : 2018 | Standard Specification for High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane for Use with Separate Wearing Course |
| ASTM C 1472 : 2006 | Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width |
| ASTM C 1193 : 2005 : REV A | Standard Guide for Use of Joint Sealants |
| ASTM C 1472 : 2016 | Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width |
| ASTM D 1752 : 2004 : REV A : R2008 | Standard Specification for Preformed Sponge Rubber Cork and Recycled PVC Expansion Joint Fillers for Concrete Paving and Structural Construction |
| ASTM D 1056 : 1968 : EDT 1 | Standard Specification for Sponge and Expanded Cellular Rubber Products |
| ASTM D 5957 : 1998 : R2005 | Standard Guide for Flood Testing Horizontal Waterproofing Installations |
| ASTM D 6506 : 2001 | Standard Specification for Asphalt Based Protection for Below-Grade Waterproofing |
| ASTM C 1193 : 2016 : REDLINE | Standard Guide for Use of Joint Sealants |
| ASTM D 5295 : 2000 : R2006 | Standard Guide for Preparation of Concrete Surfaces for Adhered (Bonded) Membrane Waterproofing Systems |
| ASTM D 1056 : 2000 | Standard Specification for Flexible Cellular Materials-Sponge or Expanded Rubber |
| ASTM D 1751 : 2023 | Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Asphalt Types) |
| ASTM C 578 : 2019 | Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation |
| ASTM D 1751 : 2018 | Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Bituminous Types) |
| ASTM D 6451/D6451M : 1999 : R2021 | Standard Guide for Application of Asphalt-Based Protection Board |
| ASTM C 1193 : 2012 | Standard Guide for Use of Joint Sealants |
| ASTM E 1907 : 2006 : REV A | Standard Guide to Methods of Evaluating Moisture Conditions of Concrete Floors to Receive Resilient Floor Coverings (Withdrawn 2008) |
| ASTM C 1299 : 1999 | Standard Guide for Use in Selection of Liquid-Applied Sealants |
| ASTM D 6134 : 1997 | Standard Specification for Vulcanized Rubber Sheets Used in Waterproofing Systems |
| ASTM C 1472 : 2016 : R2022 | Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width |
| ASTM C 1193 : 2005 | Standard Guide for Use of Joint Sealants |
| ASTM C 1471 : 2005 | Standard Guide for the Use of High Solids Content Cold Liquid-Applied Elastomeric Waterproofing Membrane on Vertical Surfaces |
| ASTM E 1907 : 2004 | Standard Guide to Methods of Evaluating Moisture Conditions of Concrete Floors to Receive Resilient Floor Coverings |
| ASTM D 1751 : 2004 | Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Bituminous Types) |
| ASTM D 1752 : 2018 | Standard Specification for Preformed Sponge Rubber, Cork and Recycled PVC Expansion Joint Fillers for Concrete Paving and Structural Construction |
| ASTM D 6451/D6451M : 1999 : R2014 : EDT 1 | Standard Guide for Application of Asphalt Based Protection Board |
| ASTM C 578 : 2022 | Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation |
| ASTM D 1751 : 2004 : R2008 | Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Bituminous Types) |
| ASTM D 6134 : 2007 : R2013 | Standard Specification for Vulcanized Rubber Sheets Used in Waterproofing Systems |
| ASTM D 5957 : 1998 : R2013 | Standard Guide for Flood Testing Horizontal Waterproofing Installations |
| ASTM D 1752 : 2018 : R2023 | Standard Specification for Preformed Sponge Rubber, Cork, and Recycled PVC Expansion Joint Fillers for Concrete Paving and Structural Construction |
| ASTM D 6451 : 1999 | Standard Guide for Application of Asphalt Based Protection Board |
| ASTM D 5957 : 1998 : R2021 | Standard Guide for Flood Testing Horizontal Waterproofing Installations |
| ASTM C 1193 : 2000 | Standard Guide for Use of Joint Sealants |
| ASTM D 1056 : 2014 | Standard Specification for Flexible Cellular Materials—Sponge or Expanded Rubber |
| ASTM D 6506 : 2001 : R2009 | Standard Specification for Asphalt Based Protection for Below-Grade Waterproofing |
| ASTM D 1056 : 2014 : REDLINE | Standard Specification for Flexible Cellular Materials—Sponge or Expanded Rubber |
| ASTM C 1471/C1471M : 2005 : R2021 | Standard Guide for the Use of High Solids Content Cold Liquid-Applied Elastomeric Waterproofing Membrane on Vertical Surfaces |
| ASTM C 1471/C1471M : 2022 | Standard Guide for the Use of High Solids Content Cold Liquid-Applied Elastomeric Waterproofing Membrane on Vertical Surfaces |
| ASTM E 1907 : 1997 | Standard Practices for Determining Moisture-Related Acceptability of Concrete Floors to Receive Moisture-Sensitive Finishes |
| ASTM D 5957 : 1998 | Standard Guide for Flood Testing Horizontal Waterproofing Installations |
| ASTM C 1299 : 2003 | Standard Guide for Use in Selection of Liquid-Applied Sealants (Withdrawn 2012) |
| ASTM C 1472 : 2016 : EDT 1 | Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width |
| ASTM C 578 : 2023 | Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation |
| ASTM C 1193 : 2011 | Standard Guide for Use of Joint Sealants |
| ASTM C 1472 : 2000 | Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width |
| ASTM C 1193 : 2013 | Standard Guide for Use of Joint Sealants |
| ASTM D 1752 : 1984 : R1996 : EDT 1 | Standard Specification for Preformed Sponge Rubber and Cork Expansion Joint Fillers for Concrete Paving and Structural Construction |
| ASTM E 1907 : 2006 | Standard Guide to Methods of Evaluating Moisture Conditions of Concrete Floors to Receive Resilient Floor Coverings |
| ASTM C 836/C836M : 2018 : R2022 | Standard Specification for High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane for Use with Separate Wearing Course |
| ASTM D 6134 : 2007 | Standard Specification for Vulcanized Rubber Sheets Used in Waterproofing Systems |
| ASTM D 1752 : 2004 : REV A | Standard Specification for Preformed Sponge Rubber Cork and Recycled PVC Expansion Joint Fillers for Concrete Paving and Structural Construction |
| ASTM C 1193 : 2009 | Standard Guide for Use of Joint Sealants |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.