• There are no items in your cart

ASTM D 1000 : 1999

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications
Superseded date

11-11-2014

Published date

03-10-1999

1.1 These test methods cover procedures for testing pressure-sensitive adhesive-coated tapes to be used as electrical insulation and are classified as follows:

1.1.1 Class 1 -Non-elastomeric backings made from materials such as: Paper, flat or creped, Fabric, uncoated or coated, Cellulose ester films, Polyethylene terephthalate (polyester) films, Fluorocarbon polymer films, Composite filament films, Polyamide films, Polyimide films, and Combinations thereof.

1.1.2 Class 2 -Elastomeric backings that are characterized by both high stretch and substantial recovery made from materials such as: Vinyl chloride and co-polymers, Vinylidene chloride and co-polymers, and Polyethylene and co-polymers.

Note 1-Laminates of Class 1 and Class 2 backings should be tested according to Class 1 test methods.

1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazards see Section 3.

1.3 The procedures appear in the sections indicated:

Paper, flat or creped, Fabric, uncoated or coated, Cellulose ester films, Polyethylene terephthalate (polyester) films, Fluorocarbon polymer films, Composite filament films, Polyamide films, Polyimide films, and Combinations thereof.

1.4 The values stated in inch-pound units are the standard, unless otherwise noted. If a value for measurement is followed by a value in SI units in parentheses, the second value may only be approximate. The first stated value is the requirement.

Committee
D 09
DocumentType
Test Method
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

ASTM D 2148 : 2018 Standard Test Methods for Bondable Silicone Rubber Tapes Used for Electrical Insulation
ASTM C 1423 : 2016 Standard Guide for Selecting Jacketing Materials for Thermal Insulation
ASTM D 2305 : 2018 Standard Test Methods for Polymeric Films Used for Electrical Insulation
ASTM D 7932 : 2017 Standard Specification for Printed, Pressure-Sensitive Adhesive Labels for Use in Extreme Distribution Environments
ASTM D 2686 : 2019 Standard Specification for Polytetrafluoroethylene-Backed Pressure-Sensitive Electrical Insulating Tape
ASTM F 2896 : 2011 : R2017 Standard Specification for Reinforced Polyethylene Composite Pipe For The Transport Of Oil And Gas And Hazardous Liquids
ASTM D 876 : 2013 Standard Test Methods for Nonrigid Vinyl Chloride Polymer Tubing Used for Electrical Insulation
ASTM D 3611 : 2006 : R2019 Standard Practice for Accelerated Aging of Pressure-Sensitive Tapes
ASTM D 2301 : 2010 : R2017 Standard Specification for Vinyl Chloride Plastic Pressure-Sensitive Electrical Insulating Tape
ASTM D 3359 : 2017 Standard Test Methods for Rating Adhesion by Tape Test
ASTM F 1790/F1790M : 2015 Standard Test Method for Measuring Cut Resistance of Materials Used in Protective Clothing with CPP Test Equipment
ASTM D 2484 : 2006 : R2012 : EDT 1 Standard Specification for Polyester Film Pressure-Sensitive Electrical Insulating Tape (Withdrawn 2020)
ASTM D 4505 : 2012 : R2017 Standard Specification for Preformed Retroreflective Pavement Marking Tape for Extended Service Life
ASTM D 4592 : 2012 : R2017 Standard Specification for Preformed Retroreflective Pavement Marking Tape for Limited Service Life
ASTM D 2754 : 2010 : R2016 Standard Specification for High-Temperature Glass Cloth Pressure-Sensitive Electrical Insulating Tape (Withdrawn 2022)
ASTM D 3005 : 2017 Standard Specification for Low-Temperature Resistant Vinyl Chloride Plastic Pressure-Sensitive Electrical Insulating Tape
ASTM D 3006 : 2010 : R2017 Standard Specification for Polyethylene Plastic Pressure-Sensitive Electrical Insulating Tape (Withdrawn 2022)
ASTM D 2510 : 1994 : R2017 Standard Test Method for Adhesion of Solid Film Lubricants
ASTM C 474 : 2015 Standard Test Methods for Joint Treatment Materials for Gypsum Board Construction
ASTM F 2992/F2992M : 2015 Standard Test Method for Measuring Cut Resistance of Materials Used in Protective Clothing with Tomodynamometer (TDM-100) Test Equipment
ASTM C 1775 : 2014 Standard Specification for Laminate Protective Jacket and Tape for Use over Thermal Insulation for Outdoor Applications
ASTM D 6343 : 2014 : R2018 Standard Test Methods for Thin Thermally Conductive Solid Materials for Electrical Insulation and Dielectric Applications

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.