• There are no items in your cart

ASTM D 1266 : 1998

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Sulfur in Petroleum Products (Lamp Method)
Available format(s)

Hardcopy , PDF

Superseded date

11-11-2014

Language(s)

English

Published date

02-10-1998

1.1 This test method covers the determination of total sulfur in liquid petroleum products in concentrations from 0.01 to 0.4 mass% (Note 1). A special sulfate analysis procedure is described in Annex A1 that permits the determination of sulfur in concentrations as low as 5 mg/kg.

Note 1-The comparable lamp method for the determination of sulfur in liquefied petroleum gas is described in Test Method D2784. For the determination of sulfur in heavier petroleum products that cannot be burned in a lamp, see the bomb method (Test Method D129) the quartz tube method (IP 63), or the high-temperature method (Test Method D1552).

1.2 The direct burning procedure (Section 9) is applicable to the analysis of such materials as gasoline, kerosine, naphtha, and other liquids that can be burned completely in a wick lamp. The blending procedure (Section 10) is applicable to the analysis of gas oils and distillate fuel oils, naphthenic acids, alkyl phenols, high sulfur content petroleum products, and many other materials that cannot be burned satisfactorily by the direct burning procedure.

1.3 Phosphorus compounds normally present in commercial gasoline do not interfere. A correction is given for the small amount of acid resulting from the combustion of the lead anti-knock fluids in gasoline's. Appreciable concentrations of acid-forming or base-forming elements from other sources interfere when the titration procedure is employed since no correction is provided in these cases.

1.4 The preferred units are acceptable metric units.

1.5 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. >For specific hazard statements, see Note 5.

Committee
D 02
DocumentType
Test Method
Pages
11
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 3699 : 2018 : REV A Standard Specification for Kerosine
ASTM D 1655 : 2019 Standard Specification for Aviation Turbine Fuels
ASTM D 6615 : 2015 : REV A Standard Specification for Jet B Wide-Cut Aviation Turbine Fuel
ASTM D 8076 : 2018 Standard Specification for 100 Research Octane Number Test Fuel for Automotive Spark-Ignition Engines
ASTM D 8147 : 2017 Standard Specification for Special-Purpose Test Fuels for Aviation Compression-Ignition Engines
ASTM D 1405/D1405M : 2008 : R2013 Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels (Withdrawn 2019)
ASTM D 7467 : 2019 Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20)
ASTM D 6823 : 2008 : R2013 Standard Specification for Commercial Boiler Fuels With Used Lubricating Oils
ASTM D 6201 : 2018 : REV A Standard Test Method for Dynamometer Evaluation of Unleaded Spark-Ignition Engine Fuel for Intake Valve Deposit Formation
ASTM D 396 : 2019 Standard Specification for Fuel Oils
ASTM D 240 : 2017 Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter
ASTM D 4809 : 2018 Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method)
ASTM D 5797 : 2018 Standard Specification for Methanol Fuel Blends (M51–M85) for Methanol-Capable Automotive Spark-Ignition Engines
ASTM D 4868 : 2017 Standard Test Method for Estimation of Net and Gross Heat of Combustion of Hydrocarbon Burner and Diesel Fuels
ASTM D 7578 : 2018 Standard Guide for Calibration Requirements for Elemental Analysis of Petroleum Products and Lubricants
ASTM D 4529 : 2017 Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels
ASTM D 4814 : 2019 Standard Specification for Automotive Spark-Ignition Engine Fuel
ASTM D 6448 : 2016 Standard Specification for Industrial Burner Fuels from Used Lubricating Oils
ASTM D 7223 : 2017 Standard Specification for Aviation Certification Turbine Fuel
ASTM D 2384 : 1983 : R2014 Standard Test Methods for Traces of Volatile Chlorides in Butane-Butene Mixtures
ASTM D 6751 : 2019 Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels
ASTM D 7455 : 2019 Standard Practice for Sample Preparation of Petroleum and Lubricant Products for Elemental Analysis
ASTM D 1018 : 2011 : R2016 Standard Test Method for Hydrogen In Petroleum Fractions (Withdrawn 2021)
ASTM D 7719 : 2018 Standard Specification for High Aromatic Content Unleaded Hydrocarbon Aviation Gasoline
ASTM D 910 : 2017 : REV A Standard Specification for Leaded Aviation Gasolines
ASTM D 3338/D3338M : 2009 : R2014 : EDT 2 Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels
ASTM D 7666 : 2012 Standard Specification for Triglyceride Burner Fuel
ASTM D 7566 : 2019 Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons
ASTM D 6227 : 2018 Standard Specification for Unleaded Aviation Gasoline Containing a Non-hydrocarbon Component
ASTM D 8256 : 2019 Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation in the Sequence VH Spark-Ignition Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions

View more information
US$83.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.