ASTM D 1474 : 1998
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
11-11-2014
English
12-31-2010
CONTAINED IN VOL. 06.01, 2014 Defines the determination of the indentation hardness of organic materials such as dried paint, varnish, and lacquer coatings, when applied to an acceptable plane rigid surface, for example, metal or glass.
1.1 These test methods cover the determination of the indentation hardness of organic materials such as dried paint, varnish, and lacquer coatings, when applied to an acceptable plane rigid surface, for example, metal or glass.
1.2 Two methods are covered as follows:
Sections Method A---Knoop Indentation Hardness 6 to 12 Method B---Pfund Indentation Hardness 13 to 191.3 Method A, which has the greater precision, provides hardness values in terms of Knoop Hardness Number (KHN). Method B provides hardness in terms of Pfund Hardness Number (PHN). Although the hardness value scales of these methods differ, the methods agree in the ranking of coating hardness.
1.4 This standard does not purport to address the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| Committee |
D 01
|
| DocumentType |
Test Method
|
| Pages |
5
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
| BS 3900-E12.2:2000 | Methods of test for paints Determination of Knoop hardness by measurement of the indentation depth |
| ASTM D 2248 : 2001 | Standard Practice for Detergent Resistance of Organic Finishes |
| ASTM D 3322 : 1982 : R2001 | Standard Practice for Testing Primers and Primer Surfacers Over Preformed Metal |
| MIL F 50869 : E | FUZE, PIBD M550 LESS SPITBACK ASSEMBLY METAL PARTS & LOADING ASSEMBLING AND PACKING |
| ASTM D 6137 : 1997 | Standard Test Method for Sulfuric Acid Resistance of Polymer Linings for Flue Gas Desulfurization Systems |
| ASTM D 3322 : 1982 : R2005 | Standard Practice for Testing Primers and Primer Surfacers Over Preformed Metal |
| ASTM D 2248 : 2001 : REV A : R2007 | Standard Practice for Detergent Resistance of Organic Finishes |
| ASTM D 3794 : 2018 | Standard Guide for Testing Coil Coatings |
| ASTM D 6943 : 2015 | Standard Practice for Immersion Testing of Industrial Protective Coatings and Linings |
| ASTM D 6577 : 2015 | Standard Guide for Testing Industrial Protective Coatings |
| ASTM D 2248 : 2001 : REV A : R2018 | Standard Practice for Detergent Resistance of Organic Finishes |
| ASTM D 3732 : 1982 : R2005 | Standard Practice for Reporting Cure Times of Ultraviolet-Cured Coatings |
| CEN/TS 1071-7 : 2003 | ADVANCED TECHNICAL CERAMICS - METHODS OF TEST FOR CERAMIC COATINGS - PART 7: DETERMINATION OF HARDNESS AND YOUNG'S MODULUS BY INSTRUMENTED INDENTATION TESTING |
| ASTM D 5499 : 1994 : R1999 | Standard Test Methods for Heat Resistance of Polymer Linings for Flue Gas Desulfurization Systems |
| ASTM D 6137 : 1997 : R2012 | Standard Test Method for Sulfuric Acid Resistance of Polymer Linings for Flue Gas Desulfurization Systems |
| ASTM C 868 : 2002 : R2012 | Standard Test Method for Chemical Resistance of Protective Linings (Withdrawn 2015) |
| A-A-50542 Revision A:1994 | COATING SYSTEM, REFLECTIVE, SLIP-RESISTANT, CHEMICAL RESISTANT URETHANE FOR MAINTENANCE FACILITY FLOORS |
| I.S. CEN TS 1071-7:2003 | ADVANCED TECHNICAL CERAMICS - METHODS OF TEST FOR CERAMIC COATINGS - PART 7: DETERMINATION OF HARDNESS AND YOUNG'S MODULUS BY INSTRUMENTED INDENTATION TESTING |
| ASTM D 6577 : 2015 : R2019 | Standard Guide for Testing Industrial Protective Coatings |
| ASTM D 6943 : 2015(R2019) | Standard Practice for Immersion Testing of Industrial Protective Coatings and Linings |
| ASTM D 3322 : 1982 : R2011 | Standard Practice for Testing Primers and Primer Surfacers Over Preformed Metal |
| ASTM D 3732 : 1982 : R2011 | Standard Practice for Reporting Cure Times of Ultraviolet-Cured Coatings |
| ASTM C 868 : 2002 | Standard Test Method for Chemical Resistance of Protective Linings |
| ASTM C 868 : 2002 : R2008 | Standard Test Method for Chemical Resistance of Protective Linings |
| ASTM D 345 : 2002 | Side bearings of the freight wagon bogies. General specifications |
| VDI/VDE 2616 Blatt 2:2014-07 | Hardness testing of plastics and elastomers |
| ASTM D 3322 : 1982 : R1996 : EDT 1 | Standard Practice for Testing Primers and Primer Surfacers Over Preformed Metal |
| MIL C 48669 : 0 | CARTRIDGE, 40MM, M918 TP, ESCAPEMENT ASSEMBLY FOR METAL PARTS AND LOADING, ASSEMBLING AND PACKAGING |
| DD CEN/TS 1071-7:2003 | Advanced technical ceramics. Methods of test for ceramic coatings Determination of hardness and Young\'s modulus by instrumented indentation testing |
| ASTM D 5499 : 1994 : R2013 | Standard Test Methods for Heat Resistance of Polymer Linings for Flue Gas Desulfurization Systems |
| ASTM D 6943 : 2015 : REDLINE | Standard Practice for Immersion Testing of Industrial Protective Coatings and Linings |
| ASTM D 5499 : 1994 : R2007 | Standard Test Methods for Heat Resistance of Polymer Linings for Flue Gas Desulfurization Systems |
| ASTM D 6137 : 1997 : R2004 | Standard Test Method for Sulfuric Acid Resistance of Polymer Linings for Flue Gas Desulfurization Systems |
| ASTM D 3451 : 2006 | Standard Guide for Testing Coating Powders and Powder Coatings |
| ASTM D 333 : 2001 : R2013 | Standard Guide for Clear and Pigmented Lacquers |
| ASTM D 4712 : 1987 : REV A : R1996 | Standard Guide for Testing Industrial Water-Reducible Coatings |
| ASTM D 2336 : 1999 | Standard Guide for Specifying Factory Applied Wood Coatings (Withdrawn 2008) |
| ASTM D 3732 : 1982 : R2017 | Standard Practice for Reporting Cure Times of Ultraviolet-Cured Coatings |
| BS 3900-E12.1:2000 | Methods of test for paints Determination of Knoop hardness by measurement of the indentation length using a microscope |
| ACI 350.2R : 2004 | CONCRETE STRUCTURES FOR CONTAINMENT OF HAZARDOUS MATERIALS |
| MIL-DTL-48669 Revision A Interim Revision:2004 | CARTRIDGE, 40 MM - M550 ESCAPEMENT ASSEMBLY |
| 05/30091636 DC : DRAFT AUG 2005 | ISO 14577-4 - METALLIC MATERIALS - INSTRUMENTED INDENTATION TEST FOR HARDNESS AND MATERIALS PARAMETERS - PART 4: TEST METHOD FOR METALLIC AND NON-METALLIC COATINGS |
| ASTM D 3451 : 2006 : R2012 | Standard Guide for Testing Coating Powders and Powder Coatings |
| ASTM D 4712 : 1987 : REV A : R2001 | Standard Guide for Testing Industrial Water-Reducible Coatings |
| ASTM D 2248 : 2001 : REV A : R2013 | Standard Practice for Detergent Resistance of Organic Finishes |
| ASTM D 3732 : 1982 : R2001 | Standard Practice for Reporting Cure Times of Ultraviolet-Cured Coatings |
| ASTM D 333 : 2001 : R2007 | Standard Guide for Clear and Pigmented Lacquers |
| ASTM D 6137 : 1997 : R2018 | Standard Test Method for Sulfuric Acid Resistance of Polymer Linings for Flue Gas Desulfurization Systems |
| ASTM D 333 : 2001 | Standard Guide for Clear and Pigmented Lacquers |
| GOST 849:2018 | Primary nickel. SpecificationsE |
| ASTM D 2248 : 2001 : REV A | Standard Practice for Detergent Resistance of Organic Finishes |
| NACE 14C296 : 0 | A STATE-OF-THE-ART REPORT ON PROTECTIVE COATINGS FOR MITIGATING CORROSION UNDER INSULATION ON RAIL TANK CARS |
| ASTM D 6577 : 2015 : REDLINE | Standard Guide for Testing Industrial Protective Coatings |
| NACE TM 01 74 : 2002 | LABORATORY METHODS FOR THE EVALUATION OF PROTECTIVE COATINGS AND LINING MATERIALS ON METALLIC SUBSTRATES IN IMMERSION SERVICE |
| ASTM D 3322 : 1982 : R2017 | Standard Practice for Testing Primers and Primer Surfacers Over Preformed Metal |
| ASTM D 4712 : 1987 : REV A : R2005 | Standard Guide for Testing Industrial Water-Reducible Coatings (Withdrawn 2014) |
| ASTM D 3451 : 2006 : R2017 | Standard Guide for Testing Coating Powders and Powder Coatings |
| ASTM D 3732 : 1982 : R1996 : EDT 1 | Standard Practice for Reporting Cure Times of Ultraviolet-Cured Coatings |
| ISO 6441-2:1999 | Paints and varnishes Determination of micro-indentation hardness Part 2: Knoop hardness by measurement of indentation depth under load |
| ASTM D 1400 : 2000 | Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Nonconductive Coatings Applied to a Nonferrous Metal Base (Withdrawn 2006) |
| ASTM D 823 : 1995 | Standard Practices for Producing Films of Uniform Thickness of Paint, Varnish, and Related Products on Test Panels |
| ASTM E 384 : 2017 : REDLINE | Standard Test Method for Microindentation Hardness of Materials |
| ISO 6441-1:1999 | Paints and varnishes Determination of micro-indentation hardness Part 1: Knoop hardness by measurement of indentation length |
| ASTM D 1186 : 2001 | Standard Test Methods for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to a Ferrous Base (Withdrawn 2006) |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.