ASTM D 1796 : 2011 : R2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure)
Hardcopy , PDF
12-17-2022
English
07-12-2016
CONTAINED IN VOL. 05.01, 2018 Specifies the laboratory determination of water and sediment in fuel oils in the range from 0% to 30% volume by means of the centrifuge procedure.
1.1This test method describes the laboratory determination of water and sediment in fuel oils in the range from 0 % to 30 % volume by means of the centrifuge procedure.
Note 1:With some types of fuel oils such as residual fuel oils or distillate fuel oils containing residual components, it is difficult to obtain water or sediment contents with this test method. When this situation is encountered, Test Method D95 (API MPMS Chapter 10.5) or Test Method D473 (API MPMS Chapter 10.1) may be used.
Note 2:API MPMS Chapter 10.6 (Test Method D1796) along with API MPMS Chapter 10.3 (Test Method D4007) formerly superseded API Standard 2548.
1.2The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific precautionary statement, see 6.1.
| Committee |
D 02
|
| DevelopmentNote |
Also numbered as API MPM CH10.6. (08/2013)
|
| DocumentType |
Test Method
|
| Pages |
7
|
| ProductNote |
Reconfirmed 2016
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM D 6666 : 2004 : R2019 | Standard Guide for Evaluation of Aqueous Polymer Quenchants |
| ASTM D 6751 : 2019 | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
| ASTM D 4868 : 2017 | Standard Test Method for Estimation of Net and Gross Heat of Combustion of Hydrocarbon Burner and Diesel Fuels |
| ASTM D 4418 : 2017 | Standard Practice for Receipt, Storage, and Handling of Fuels for Gas Turbines |
| ASTM D 2709 : 2016 | Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge |
| ASTM D 6823 : 2008 : R2013 | Standard Specification for Commercial Boiler Fuels With Used Lubricating Oils |
| ASTM D 2711 : 2017 | Standard Test Method for Demulsibility Characteristics of Lubricating Oils |
| ASTM D 6618 : 2016 | Standard Test Method for Evaluation of Engine Oils in Diesel Four-Stroke Cycle Supercharged 1M-PC Single Cylinder Oil Test Engine |
| ASTM D 6750 : 2019 | Standard Test Methods for Evaluation of Engine Oils in a High-Speed, Single-Cylinder Diesel Engine—1K Procedure (0.4 % Fuel Sulfur) and 1N Procedure (0.04 % Fuel Sulfur) |
| ASTM D 2158 : 2016 : REV A : EDT 1 | Standard Test Method for Residues in Liquefied Petroleum (LP) Gases |
| ASTM D 6448 : 2016 | Standard Specification for Industrial Burner Fuels from Used Lubricating Oils |
| ASTM D 6448 : 2016 : R2022 | Standard Specification for Industrial Burner Fuels from Used Lubricating Oils |
| ASTM D 6666 : 2020 | Standard Guide for Evaluation of Aqueous Polymer Quenchants |
| ASTM D 2711 : 2022 | Standard Test Method for Demulsibility Characteristics of Lubricating Oils |
| ASTM D 2880 : 2020 | Standard Specification for Gas Turbine Fuel Oils |
| ASTM D 2158 : 2021 | Standard Test Method for Residues in Liquefied Petroleum (LP) Gases |
| ASTM F 1084 : 2008 : R2018 | Standard Guide for Sampling Oil/Water Mixtures for Oil Spill Recovery Equipment |
| ASTM F 2084/F2084M : 2001 : R2018 | Standard Guide for Collecting Containment Boom Performance Data in Controlled Environments |
| ASTM D 1290 : 1995 : R2021 | Standard Test Method for Sediment in Water-Emulsion Polishes by Centrifuge |
| ASTM D 975 : 2022 : REV A | Standard Specification for Diesel Fuel |
| ASTM D 6823 : 2008 : R2021 | Standard Specification for Commercial Boiler Fuels With Used Lubricating Oils |
| ASTM D 6750 : 2019 : EDT 1 | Standard Test Methods for Evaluation of Engine Oils in a High-Speed, Single-Cylinder Diesel Engine—1K Procedure (0.4 % Fuel Sulfur) and 1N Procedure (0.04 % Fuel Sulfur) |
| ASTM D 6751 : 2020 : REV A | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
| ASTM D 7666 : 2012 : R2019 | Standard Specification for Triglyceride Burner Fuel |
| ASTM D 5828 : 1997 : R2018 | Standard Test Method for Compatibility of Supplemental Coolant Additives (SCAs) and Engine Coolant Concentrates |
| ASTM D 4381 : 2022 | Standard Test Method for Sand Content by Volume of Construction Slurries |
| ASTM D 2709 : 2022 | Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge |
| ASTM F 715 : 2007 : R2018 | Standard Test Methods for Coated Fabrics Used for Oil Spill Control and Storage |
| ASTM D 4418 : 2022 | Standard Practice for Receipt, Storage, and Handling of Fuels for Gas Turbines |
| ASTM D 7666 : 2012 | Standard Specification for Triglyceride Burner Fuel |
| ASTM D 1290 : 1995 : R2015 | Standard Test Method for Sediment in Water-Emulsion Polishes by Centrifuge |
| ASTM D 6304:2016 | Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fischer Titration |
| ASTM D 6304 : 2004 : REV A : EDT 1 | Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fisher Titration |
| API MPM CH10.5 : 2013 | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 10.5: STANDARD TEST METHOD FOR WATER IN PETROLEUM PRODUCTS AND BITUMINOUS MATERIALS BY DISTILLATION |
| ASTM D 6304 : 2007 | Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fischer Titration (Withdrawn 2016) |
| ASTM D 6304 : 2004 | Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fisher Titration |
| ASTM D 6304 : 2016 : EDT 1 | Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fischer Titration |
| ASTM E 542 : 2001 : R2021 | Standard Practice for Calibration of Laboratory Volumetric Apparatus |
| ASTM D 6304 : 2004 : REV A | Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fisher Titration |
| ASTM D 6304 : 2004 : EDT 1 | Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fisher Titration |
| ASTM D 6304 : 2000 | Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fisher Titration |
| ISO 5272:1979 | Toluene for industrial use — Specifications |
| API MPM CH8.1 : 2013 | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 8.1: STANDARD PRACTICE FOR MANUAL SAMPLING OF PETROLEUM AND PETROLEUM PRODUCTS |
| ASTM D 6304 : 2003 | Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fisher Titration |
| ASTM E 542 : 2001 : R2012 | Standard Practice for Calibration of Laboratory Volumetric Apparatus |
| ASTM E 542 : 2022 | Standard Practice for Gravimetric Calibration of Laboratory Volumetric Instruments |
| API MPM CH8.2 : 2016 | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 8.2: STANDARD PRACTICE FOR AUTOMATIC SAMPLING OF PETROLEUM AND PETROLEUM PRODUCTS |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.