• There are no items in your cart

ASTM D 1879 : 2006 : R2014

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Practice for Exposure of Adhesive Specimens to Ionizing Radiation
Available format(s)

Hardcopy , PDF

Superseded date

01-13-2023

Language(s)

English

Published date

03-21-2014

CONTAINED IN VOL. 15.06, 2015 Defines conditions for the exposure of polymeric adhesives in bonded specimens to ionizing radiation prior to determination of radiation-induced changes in physical or chemical properties.

1.1The purpose of this practice is to define conditions for the exposure of polymeric adhesives in bonded specimens to ionizing radiation prior to determination of radiation-induced changes in physical or chemical properties. This recommended practice specifically covers the following kinds of radiation: gamma or X-ray radiation, electron or beta radiation, neutrons, and mixtures of these such as reactor radiation.

1.2This practice specifies only the conditions of irradiation but does not cover the preparation of test specimens, testing conditions, or the evaluation of test. These are covered in the various ASTM methods or specifications for specific materials.

1.3This practice covers procedures for the following five types of exposure:

ProcedureA—Exposure at ambient conditions.

ProcedureB—Exposure at controlled temperature.

ProcedureC—Exposure in a medium other than air.

ProcedureD—Exposure under load.

ProcedureE—Exposure combining two or more of the variables listed in Procedures A to D.

Note 1The problems of measuring the properties of materials during irradiation involve shielding and remote control facilities and are, therefore, not considered in this practice.

1.4The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information purposes only.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.5.1Electrical Hazard:Warning—The users of this practice must be aware that there are inherent dangers associated with the use of electrical instrumentation and that this practice cannot and will not substitute for a practical knowledge of the instrument used for a particular procedure.

1.5.2Radio Frequency:Warning—Persons with pacemakers may be affected by the radio frequency.

Committee
D 14
DocumentType
Standard Practice
Pages
5
ProductNote
Reconfirmed 2014
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 6465 : 1999 : R2016 Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants

ASTM D 618 : 2013 : REDLINE Standard Practice for Conditioning Plastics for Testing
ISO/ASTM 51702:2013 Practice for dosimetry in a gamma facility for radiation processing
ASTM D 2953 : 1971 : EDT 2 Classification System for Polymeric Materials for Service in Ionizing Radiation
ASTM E 2005:2010 Standard Guide for Benchmark Testing of Reactor Dosimetry in Standard and Reference Neutron Fields
ASTM E 720 : 2016 : REDLINE Standard Guide for Selection and Use of Neutron Sensors for Determining Neutron Spectra Employed in Radiation-Hardness Testing of Electronics
ASTM E 2005 : 2010 : R2015 Standard Guide for Benchmark Testing of Reactor Dosimetry in Standard and Reference Neutron Fields
ASTM E 2005 : 2005 Standard Guide for Benchmark Testing of Reactor Dosimetry in Standard and Reference Neutron Fields
ISO/ASTM 51818:2013 Practice for dosimetry in an electron beam facility for radiation processing at energies between 80 and 300 keV
ISO/ASTM 51261:2013 Practice for calibration of routine dosimetry systems for radiation processing
ASTM E 2005 : 1999 Standard Guide for Benchmark Testing of Reactor Dosimetry in Standard and Reference Neutron Fields
ASTM E 720 : 2002 Standard Guide for Selection and Use of Neutron Sensors for Determining Neutron Spectra Employed in Radiation-Hardness Testing of Electronics
ASTM E 2005 : 2005 : EDT 1 Standard Guide for Benchmark Testing of Reactor Dosimetry in Standard and Reference Neutron Fields
ASTM E 170 : 2017 : REDLINE Standard Terminology Relating to Radiation Measurements and Dosimetry
ASTM E 666 : 2021 Standard Practice for Calculating Absorbed Dose From Gamma or X Radiation
ASTM E 261 : 2016 Standard Practice for Determining Neutron Fluence, Fluence Rate, and Spectra by Radioactivation Techniques
ANSI N1.1 : 1976 NUCLEAR SAFETY - CRITICAL EXPERIMENTS, SAFETY GUIDE FOR THE PERFORMANCE OF
ASTM E 2005 : 2021 Standard Guide for Benchmark Testing of Reactor Dosimetry in Standard and Reference Neutron Fields
ASTM D 907 : 2015 : REDLINE Standard Terminology of Adhesives
ASTM D 618 : 2013 Standard Practice for Conditioning Plastics for Testing
IEEE 323-2003 IEEE Standard for Qualifying Class 1E Equipment for Nuclear Power Generating Stations
ASTM E 261 : 2016 : REDLINE Standard Practice for Determining Neutron Fluence, Fluence Rate, and Spectra by Radioactivation Techniques
ASTM D 2953 : 1971 Classification System for Polymeric Materials for Service in Ionizing Radiation (Withdrawn 1984)
ISO/ASTM 51649:2015 Practice for dosimetry in an electron beam facility for radiation processing at energies between 300 keV and 25 MeV
ASTM E 720 : 1994 Standard Guide for Selection and Use of Neutron-Activation Foils for Determining Neutron Spectra Employed in Radiation-Hardness Testing of Electronics
ASTM E 666 : 2014 : REDLINE Standard Practice for Calculating Absorbed Dose From Gamma or X Radiation
ASTM E 261 : 2016 : R2021 Standard Practice for Determining Neutron Fluence, Fluence Rate, and Spectra by Radioactivation Techniques
ASTM D 618 : 2021 Standard Practice for Conditioning Plastics for Testing
ASTM E 666 : 2014 Standard Practice for Calculating Absorbed Dose From Gamma or X Radiation

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.