• There are no items in your cart

ASTM D 2419 : 2014 : REDLINE

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Sand Equivalent Value of Soils and Fine Aggregate
Available format(s)

PDF

Superseded date

09-29-2022

Language(s)

English

Published date

09-10-2014

CONTAINED IN VOL. 04.03, 2015 Pertains to serve as a rapid field-correlation test.

1.1This test method is intended to serve as a rapid field-correlation test. The purpose of this test method is to indicate, under standard conditions, the relative proportions of clay-size or plastic fines and dust in granular soils and fine aggregates that pass the 4.75-mm (No. 4) sieve. The term “sand equivalent” expresses the concept that most granular soils and some fine aggregates are mixtures of desirable coarse particles, sand-size particles, and generally undesirable clay or plastic fines and dust.

Note 1:For fine aggregates containing clean dust of fracture (clay-size particles that are not clay minerals), test results will depend on the amount of fines present in the material. In this case other tests such as Methylene Blue Value (AASHTO T330) or X-Ray Diffraction (XRD) may be needed to determine if the fines are deleterious.

Note 2:Some agencies perform the test on material with a top size smaller than the 4.75-mm (No. 4) sieve. This is done to avoid trapping the clay-size or plastic fines and dust below flaky shaped 4.75 to 2.36 mm (No. 4 to 8) sized particles. Testing smaller top sized material may lower the numerical results of the test.

1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.2.1Regarding sieves, per Specification E11 Section 1.2, “the values stated in SI units shall be considered standard for the dimensions of the wire cloth openings and the diameter of the wires used in the wire cloth. The values stated in inchpound units shall be considered standard with regard to the sieve frames.” When sieve mesh sizes are referenced, the alternate inch-pound designations are provided for information purposes and enclosed in parentheses.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
D 04
DocumentType
Redline
Pages
10
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

ASTM D 3744 : 2003 Standard Test Method for Aggregate Durability Index
ASTM D 3910 : 2015 : REDLINE Standard Practices for Design, Testing, and Construction of Slurry Seal
ASTM D 3089 : 1997 : R2008 Standard Practice for Determining the A-D Dimension of Aerosol Valve Dip Tubes
ASTM D 7064/D7064M : 2008 : EDT 1 Standard Practice for Open-Graded Friction Course (OGFC) Mix Design
ACI 207.5R : 2011 REPORT ON ROLLER-COMPACTED MASS CONCRETE
ASTM D 6932/D6932M : 2008 Standard Guide for Materials and Construction of Open-Graded Friction Course Plant Mixtures
ASTM D 7064 : 2004 Standard Practice for Open-Graded Friction Course (OGFC) Mix Design
ACI 304R : 2000 GUIDE FOR MEASURING, MIXING, TRANSPORTING AND PLACING CONCRETE
ASTM D 6372 : 2015 : REDLINE Standard Practice for Design, Testing, and Construction of Microsurfacing
ASTM D 7064/D7064M : 2008 : R2013 Standard Practice for Open-Graded Friction Course (OGFC) Mix Design
ASTM D 5711 : 2003 Standard Test Method for Determining the Adherent Coating on Coarse Aggregates (Withdrawn 2012)
ASTM D 2940/D2940M : 2015 : REDLINE Standard Specification for Graded Aggregate Material For Bases or Subbases for Highways or Airports
ACI 221R : 1996 GUIDE FOR USE OF NORMAL WEIGHT AND HEAVYWEIGHT AGGREGATES IN CONCRETE
ASTM C 1077 : 2017 : REDLINE Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation
ASTM D 4223 : 1999 Standard Practice for Preparation of Test Specimens of Asphalt-Stabilized Soils
ASTM D 4223/D4223M : 2012 Standard Practice for Preparation of Test Specimens of Asphalt-Stabilized Soils
ASTM D 2940 : 2003 Standard Specification for Graded Aggregate Material For Bases or Subbases for Highways or Airports
ASTM D 6932 : 2004 Standard Guide for Materials and Construction of Open-Graded Friction Course Plant Mixtures
ACI ITG-4.2R : 2006 MATERIALS AND QUALITY CONSIDERATIONS FOR HIGH-STRENGTH CONCRETE IN MODERATE TO HIGH SEISMIC APPLICATIONS
ASTM D 4223 : 1999 : R2006 Standard Practice for Preparation of Test Specimens of Asphalt-Stabilized Soils
ASTM D 7064/D7064M : 2008 Standard Practice for Open-Graded Friction Course (OGFC) Mix Design
ASTM D 6932/D6932M : 2008 : R2013 Standard Guide for Materials and Construction of Open-Graded Friction Course Plant Mixtures
ASTM D 7564/D7564M : 2016 : REDLINE Standard Practice for Construction of Asphalt-Rubber Cape Seal

ASTM D 75 : 2003 Standard Practice for Sampling Aggregates
AASHTO T 176 : 2008 METHOD OF TEST FOR PLASTIC FINES IN GRADED AGGREGATES AND SOILS BY USE OF THE SAND EQUIVALENT TEST
ASTM D 3666 : 2016 : REDLINE Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM C 702 : 1998 Standard Practice for Reducing Samples of Aggregate to Testing Size
ASTM E 11 : 2017 : REDLINE Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves
ASTM C 670 : 2015 : REDLINE Standard Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials
ASTM D 653 : 2014 : REDLINE Standard Terminology Relating to Soil, Rock, and Contained Fluids

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.