• There are no items in your cart

ASTM D 2513 : 2019

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings
Available format(s)

Hardcopy , PDF

Superseded date

12-15-2020

Language(s)

English

Published date

08-16-2019

This specification covers requirements and test methods for material dimensions and tolerances, hydrostatic burst strength, chemical resistance, and rapid crack resistance of polyethylene pipe, tubing, and fittings for use in fuel gas pipelines for direct burial and reliner applications.

1.1This specification covers requirements and test methods for material dimensions and tolerances, hydrostatic burst strength, chemical resistance, and rapid crack resistance of polyethylene pipe, tubing, and fittings for use in fuel gas pipelines for direct burial and reliner applications. The pipe and fittings covered by this specification are intended for use in the transmission and distribution of natural gas. Requirements for the qualifying of polyethylene systems for use with liquefied petroleum gas are also covered.

1.1.1This specification does not cover threaded pipe. Design considerations are discussed in Appendix X1. In-plant quality control programs are specified in Annex A1 and Annex A2.

1.1.2See Specification F2619/F2619M for polyethylene piping for pressure or non-pressure oil and gas producing applications to convey fluids such as oil, dry or wet gas, multiphase fluids, and non-potable oilfield water.

1.2The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.

1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4The following is an index of the annexes and appendix in this specification:

Annex

Subject

Annex A1

In-Plant Quality Control for all materials up to 12 in.

Annex A2

In-Plant Quality Control for PE materials 14 in. and larger.

Appendixes

Subject

Appendix X1

Design Consideration

1.5The following precautionary caveat pertains only to the test method portion, Section 6, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
F 17
DocumentType
Standard
Pages
18
ProductNote
THIS DOCUMENT ALSO REFERS TO - PPI TN-30/2006,PPI TR-33,PPI TR-3, PPI TR-9, ANSI B16.40
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM F 1041 : 2002 : R2016 Standard Guide for Squeeze-Off of Polyolefin Gas Pressure Pipe and Tubing
ASTM F 2830 : 2011 : R2017 Standard Specification for Manufacture and Joining of Polyethylene (PE) Gas Pressure Pipe With a Peelable Polypropylene (PP) Outer Layer
ASTM F 1734 : 2019 Standard Practice for Qualification of a Combination of Squeeze Tool, Pipe, and Squeeze-Off Procedures to Avoid Long-Term Damage in Polyethylene (PE) Gas Pipe
ASTM F 2896 : 2011 : R2017 Standard Specification for Reinforced Polyethylene Composite Pipe For The Transport Of Oil And Gas And Hazardous Liquids
ASTM F 1588 : 1996 : R2015 Standard Test Method for Constant Tensile Load Joint Test (CTLJT)
ASTM F 2897 : 2015 : REV A Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances)
ASTM F 1924 : 2019 Standard Specification for Plastic Mechanical Fittings for Use on Outside Diameter Controlled Polyethylene Gas Distribution Pipe and Tubing
ASTM F 1804 : 2008 : R2016 Standard Practice for Determining Allowable Tensile Load for Polyethylene (PE) Gas Pipe During Pull-In Installation
ASTM F 2634 : 2015 Standard Test Method for Laboratory Testing of Polyethylene (PE) Butt Fusion Joints using Tensile-Impact Method
ASTM F 1056 : 2018 Standard Specification for Socket Fusion Tools for Use in Socket Fusion Joining Polyethylene Pipe or Tubing and Fittings
ASTM F 905 : 2004 : R2018 Standard Practice for Qualification of Polyethylene Saddle-Fused Joints
ASTM F 2509 : 2015 : R2019 Standard Specification for Field-assembled Anodeless Riser Kits for Use on Outside Diameter Controlled Polyethylene and Polyamide-11 (PA11) Gas Distribution Pipe and Tubing
ASTM F 1055 : 2016 : REV A Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing
ASTM F 412 : 2019 Standard Terminology Relating to Plastic Piping Systems
ASTM F 1563 : 2001 : R2011 Standard Specification for Tools to Squeeze-off Polyethylene (PE) Gas Pipe or Tubing
ASTM F 1962 : 2011 Standard Guide for Use of Maxi-Horizontal Directional Drilling for Placement of Polyethylene Pipe or Conduit Under Obstacles, Including River Crossings (Withdrawn 2020)
ASTM F 2818 : 2010 : R2014 : EDT 1 Standard Specification for Specification for Crosslinked Polyethylene (PEX) Material Gas Pressure Pipe and Tubing
ASTM F 2880 : 2014 Standard Specification for Lap-Joint Type Flange Adapters for Polyethylene Pressure Pipe in Nominal Pipe Sizes <fraction><num>3/4</den></fraction > in. to 65 in.

ASTM F 1563 : 2001 : R2011 Standard Specification for Tools to Squeeze-off Polyethylene (PE) Gas Pipe or Tubing
ASTM D 2290 : 2019 : REV A Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe
ASTM D 3261 : 2016 Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing
ASTM D 2290 : 2019 Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe
ASTM F 1563 : 2001 : R2019 Standard Specification for Tools to Squeeze-off Polyethylene (PE) Gas Pipe or Tubing

View more information
US$83.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.