ASTM D 2665 : 2014 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
09-03-2020
English
05-01-2014
CONTAINED IN VOL. 08.04, 2017 Defines requirements and test methods for materials, dimensions and tolerances, pipe stiffness, crush resistance, impact resistance, and solvent cement for poly(vinyl chloride) plastic drain, waste, and vent pipe and fittings.
1.1This specification covers requirements and test methods for materials, dimensions and tolerances, pipe stiffness, crush resistance, impact resistance, and solvent cement for poly(vinyl chloride) plastic drain, waste, and vent pipe and fittings. A form of marking is also included. Plastic which does not meet the material requirements specified in Section 5 is excluded. Installation procedures are given in the Appendix.
1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.4The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| Committee |
F 17
|
| DevelopmentNote |
Supersedes L P 320 (B). (05/2004)
|
| DocumentType |
Redline
|
| Pages |
9
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
| ASTM F 2135 : 2001 | Standard Specification for Molded Drain, Waste, and Vent (DWV) Short-Pattern Plastic Fittings |
| ASTM D 2481 : 2005 | Standard Test Method for Accelerated Evaluation of Wood Preservatives for Marine Services by Means of Small Size Specimens (Withdrawn 2014) |
| ASTM F 2135 : 2001 : R2017 | Standard Specification for Molded Drain, Waste, and Vent (DWV) Short-Pattern Plastic Fittings |
| ASTM F 2946 : 2012 : R2017 | Standard Specification for PVC Hub and Elastomeric Seal (Gasket) Tee Connection for Joining Plastic Pipe to Insitu Pipelines and Manholes |
| ASTM F 409 : 2017 : REDLINE | Standard Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings |
| ASTM F 2135 : 2001 : R2017 : EDT 1 | Standard Specification for Molded Drain, Waste, and Vent (DWV) Short-Pattern Plastic Fittings |
| ICC 2009 INT. RESI.CODE & COMM.-I1 : 2009 | 2009 INTERNATIONAL RESIDENTIAL CODE & COMMENTARY - VOLUME 2: CHAPTERS 12 TO 44 |
| CSA B45.13 : 2014 | VACUUM WASTE-COLLECTION SYSTEMS |
| CSA 2.3 : 2016 | GAS-FIRED CENTRAL FURNACES |
| CSA 4.9 : 2017 | GAS-FIRED LOW PRESSURE STEAM AND HOT WATER BOILERS |
| ANSI Z21.10.3-2017/CSA 4.3:2017 | GAS-FIRED WATER HEATERS, VOLUME 3, STORAGE WATER HEATERS WITH INPUT RATINGS ABOVE 75,000 BTU PER HOUR, CIRCULATING AND INSTANTANEOUS |
| ANSI Z21.13 : 2017 | GAS-FIRED LOW PRESSURE STEAM AND HOT WATER BOILERS |
| ASTM D 3138 : 2004 | Standard Specification for Solvent Cements for Transition Joints Between Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Non-Pressure Piping Components |
| ASTM F 1499 : 2017 : REDLINE | Standard Specification for Coextruded Composite Drain, Waste, and Vent Pipe (DWV) |
| ASTM D 3311 : 2017 : REDLINE | Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns |
| ASTM F 2135 : 2001 : R2012 | Standard Specification for Molded Drain, Waste, and Vent (DWV) Short-Pattern Plastic Fittings |
| ANSI Z21.10.3 : 2015 | GAS-FIRED WATER HEATERS, VOLUME 3, STORAGE WATER HEATERS WITH INPUT RATINGS ABOVE 75,000 BTU PER HOUR, CIRCULATING AND INSTANTANEOUS |
| ASME A112.14.3 : 2000 : R2004 | HYDROMECHANICAL GREASE INTERCEPTORS |
| ASME A112.14.3 : 2000 : R2014 | HYDROMECHANICAL GREASE INTERCEPTORS |
| ICC 2012 INT. PVT. SEWAGE DISP.CODE : 2012 | INTERNATIONAL PRIVATE SEWAGE DISPOSAL CODE |
| ASTM D 2672 : 2014 : REDLINE | Standard Specification for Joints for IPS PVC Pipe Using Solvent Cement |
| ASTM F 3128 : 2015 | Standard Specification for Poly(Vinyl Chloride) (PVC) Schedule 40 Drain, Waste, and Vent Pipe with a Cellular Core |
| ASTM D 7209 : 2006 | Standard Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products (Withdrawn 2015) |
| ANSI Z21-10-3 : 2017 | GAS-FIRED WATER HEATERS, VOLUME 3, STORAGE WATER HEATERS WITH INPUT RATINGS ABOVE 75,000 BTU PER HOUR, CIRCULATING AND INSTANTANEOUS |
| ASTM F 2946 :2012 | Standard Specification for PVC Hub and Elastomeric Seal (Gasket) Tee Connection for Joining Plastic Pipe to Insitu Pipelines and Manholes |
| ASTM D 2855 : 2015 : REDLINE | Standard Practice for the Two-Step (Primer and Solvent Cement) Method of Joining Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Piping Components with Tapered Sockets |
| ASTM F 1760 : 2016 : REDLINE | Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Non-Pressure Plastic Pipe Having Reprocessed-Recycled Content |
| ICC IPC CODE & COMMENTARY : 2015 | IPC® Code and Commentary |
| ICC IRC CODE AND COMMENTARY VOLUME 2 : 2015 | IRC® Code and Commentary, Volume 2 |
| ICC 2012 INTERNATIONAL RESI. CODE : 2012 | INTERNATIONAL RESIDENTIAL CODE FOR ONE- AND TWO-FAMILY DWELLINGS |
| ICC 2012 INTERNATIONAL PLUMBING CODE : 2012 | INTERNATIONAL PLUMBING CODE (INCLUDES IPSDC) |
| CSA B125.2 : 2015 | PLUMBING WASTE FITTINGS |
| CSA B602 : 2016 | MECHANICAL COUPLINGS FOR DRAIN, WASTE, AND VENT PIPE AND SEWER PIPE |
| ASTM F 2726 : 2008 | Standard specification for fixation devices for tracheal tubes and other airway devices |
| IAPMO IGC 166 : 2001 E1(R2013) | PLASTIC DWV TO SEWER ADAPTER FITTINGS |
| ASTM F 2021 : 2017 : REDLINE | Standard Guide for Design and Installation of Plastic Siphonic Roof Drainage Systems |
| ASTM F 2536 : 2017 : REDLINE | Standard Guide for Installing Plastic DWV Piping Suspended from On-Grade Slabs |
| CSA B79 : 2008 : R2013 | COMMERCIAL AND RESIDENTIAL DRAINS AND CLEANOUTS |
| ASTM F 1866 : 2018 : REDLINE | Standard Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings |
| ICC IPSDC INTERNATIONAL PVT. SEWAGE DISPOSAL CODE : 2015 | INTERNATIONAL PRIVATE SEWAGE DISPOSAL CODE |
| ANSI Z21.47 : 2016 | GAS-FIRED CENTRAL FURNACES |
| B79-08 (R2018) | Commercial and residential drains and cleanouts |
| CSA B 79 : 2008 | COMMERCIAL AND RESIDENTIAL DRAINS AND CLEANOUTS |
| NSF 14 : 2016 | PLASTICS PIPING SYSTEM COMPONENTS AND RELATED MATERIALS |
| ASTM F 2135 : 2001 : R2007 | Standard Specification for Molded Drain, Waste, and Vent (DWV) Short-Pattern Plastic Fittings |
| ASTM D 3138 : 2004 : R2011 | Standard Specification for Solvent Cements for Transition Joints Between Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Non-Pressure Piping Components |
| ASTM D 3138 : 2004 : R2016 | Standard Specification for Solvent Cements for Transition Joints Between Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Non-Pressure Piping Components |
| ASTM F 891 : 2016 : REDLINE | Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Plastic Pipe With a Cellular Core |
| ASME A112.4.4 : 2017 | PLASTIC PUSH-FIT DRAIN, WASTE, AND VENT (DWV) FITTINGS |
| ASME A112.6.4 : 2003 : R2008 | ROOF, DECK, AND BALCONY DRAINS |
| ASME A112.6.4 : 2003 : R2012 | ROOF, DECK, AND BALCONY DRAINS |
| ASME A112.14.1 : 2003 | BACKWATER VALVES |
| AS ME A112.6.7:2010 | SANITARY FLOOR SINKS |
| ASME A112.14.1 : 2003 : R2008 | BACKWATER VALVES |
| ASME A112.6.3 : 2016 | FLOOR AND TRENCH DRAINS |
| ASME A112.14.1 : 2003 : R2017 | BACKWATER VALVES |
| ASME A112.14.1 : 2003 : R2012 | BACKWATER VALVES |
| ASME A112.18.2 : 2015 | PLUMBING WASTE FITTINGS |
| ASME A112.6.4 : 2003 | ROOF, DECK, AND BALCONY DRAINS |
| ASME A112.6.7 : 2010 : R2015 | SANITARY FLOOR SINKS |
| ASTM D 618 : 2013 : REDLINE | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 3311 : 2017 : REDLINE | Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns |
| ASTM D 2444 : 1999 | Standard Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight) |
| ASTM D 2122 : 2016 : REDLINE | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 1784 : 2011 : REDLINE | Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.