ASTM D 2683 : 2014
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing
Available format(s)
Hardcopy , PDF
Superseded date
11-19-2020
Language(s)
English
Published date
12-15-2014
1.1This specification covers polyethylene socket-type fittings for use with outside diameter-controlled polyethylene pipe as specified by Specifications D3035 and D2513. Requirements for materials, workmanship, dimensions, and pressure performance are included. Where applicable in this specification, “ pipe” shall mean “pipe and tubing.”
1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| Committee |
F 17
|
| DocumentType |
Standard
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM F 2619/F2619M : 2013 | Standard Specification for High-Density Polyethylene (PE) Line Pipe |
| ASTM F 412 : 2019 | Standard Terminology Relating to Plastic Piping Systems |
| ASTM F 2769 : 2018 | Standard Specification for Polyethylene of Raised Temperature (PE-RT) Plastic Hot and Cold-Water Tubing and Distribution Systems |
| ASTM F 905 : 2004 : R2018 | Standard Practice for Qualification of Polyethylene Saddle-Fused Joints |
| ASTM F 645 : 2018 : REV B | Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems |
| ASTM F 1056 : 2018 | Standard Specification for Socket Fusion Tools for Use in Socket Fusion Joining Polyethylene Pipe or Tubing and Fittings |
| ASTM F 2623 : 2019 | Standard Specification for Polyethylene of Raised Temperature (PE-RT) Systems for Non-Potable Water Applications |
| NFPA 58:2024 | Liqueed Petroleum Gas Code |
| ASTM D 1600 : 1999 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 3035 : 2003 | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter |
| ASTM D 3035 : 2012 | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter |
| ASTM D 1598 : 2002 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 2513 : 2006 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2122 : 1998 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2513 : 2016 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1598 : 2015 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 1598 : 2015 : REV A | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 2513 : 2003 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 3035 : 2014 | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter |
| ASTM D 2513 : 2012 : REV A | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 3035 : 2012 : EDT 2 | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter |
| ASTM D 2513 : 2008 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2011 : REV B | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2006 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2009 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2004 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 1987 | Standard Specification for Thermoplastic Gas Pressure Piping Systems |
| ASTM D 3350 : 2000 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 3035 : 2006 | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter |
| ASTM D 2513 : 2011 : REV C | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 3350 : 2008 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 2513 : 2016 : REV A | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2013 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 1999 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 3035 : 2015 | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter |
| ASTM D 3350 : 2002 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 2513 : 2009 : REV A | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1600 : 2007 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 2513 : 2003 : REV B | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 3035 : 2003 : REV A | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter |
| ASTM D 1600 : 2013 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 2513 : 2001 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 3350 : 2014 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 2513 : 2001 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1600 : 2014 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 2513 : 2001 : REV A : EDT 1 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1600 : 2008 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1598 : 1997 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 3035 : 2010 | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter |
| ASTM D 2513 : 2011 : EDT 1 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2014 : EDT 1 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 3035 : 1995 | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter |
| ASTM D 3350 : 2004 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 3035 : 2008 | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter |
| ASTM D 3350 : 2002 : REV A | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 1599 : 2014 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 2657 : 2007 : R2015 | Standard Practice for Heat Fusion Joining of Polyolefin Pipe and Fittings |
| ASTM D 2513 : 2014 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1599 : 2014 : EDT 1 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 3350 : 2012 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 2513 : 2000 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2007 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 3350 : 2001 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 2513 : 2011 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 3350 : 2012 : EDT 1 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 2122 : 1998 : EDT 1 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2513 : 2008 : REV B | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2003 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1599 : 2018 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 1599 : 1999 : R2011 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 1599 : 1999 : EDT 1 | Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2006 : REV B | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 3035 : 2001 | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter |
| ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
| ASTM D 2657 : 2007 | Standard Practice for Heat Fusion Joining of Polyolefin Pipe and Fittings |
| ASTM D 3350 : 2010 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 3035 : 2012 : EDT 1 | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter |
| ASTM D 2513 : 2007 : REV B : EDT 1 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2008 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1598 : 2002 : R2008 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 2513 : 2018 : REV A | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 3350 : 2006 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 2122 : 1998 : R2004 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 3350 : 2010 : REV A | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 2657 : 2003 | Standard Practice for Heat Fusion Joining of Polyolefin Pipe and Fittings |
| ASTM D 2122 : 2016 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 1599 : 1999 : R2005 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 1598 : 2002 : R2009 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 2513 : 2007 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2007 : REV B | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2012 : REV A : EDT 1 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2122 : 1998 : R2010 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2513 : 2018 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2011 : REV A | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2012 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1599 : 1999 | Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 3035 : 2014 : REV A | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter |
| ASTM D 3350 : 2005 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 2513 : 2004 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2122 : 2015 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2657 : 1997 | Standard Practice for Heat Fusion Joining of Polyolefin Pipe and Fittings |
| ASTM D 2513 : 2005 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
US$75.00
Excluding Tax where applicable
USD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.