• There are no items in your cart

ASTM D 2887 : 2019 : REV A : EDT 2

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography
Available format(s)

Hardcopy , PDF

Superseded date

10-10-2022

Language(s)

English

Published date

10-30-2020

1.1This test method covers the determination of the boiling range distribution of petroleum products. The test method is applicable to petroleum products and fractions having a final boiling point of 538 °C (1000 °F) or lower at atmospheric pressure as measured by this test method. This test method is limited to samples having a boiling range greater than 55.5 °C (100 °F), and having a vapor pressure sufficiently low to permit sampling at ambient temperature.

Note 1:Since a boiling range is the difference between two temperatures, only the constant of 1.8 °F/°C is used in the conversion of the temperature range from one system of units to another.

1.1.1Procedure A (Sections 6 – 14)—Allows a larger selection of columns and analysis conditions such as packed and capillary columns as well as a Thermal Conductivity Detector in addition to the Flame Ionization Detector. Analysis times range from 14 min to 60 min.

1.1.2Procedure B (Sections 15 – 23)—Is restricted to only 3 capillary columns and requires no sample dilution. In addition, Procedure B is used not only for the sample types described in Procedure A but also for the analysis of samples containing biodiesel mixtures B5, B10, and B20. The analysis time, when using Procedure B (Accelerated D2887), is reduced to about 8 min.

1.2This test method is not to be used for the analysis of gasoline samples or gasoline components. These types of samples must be analyzed by Test Method D7096.

1.3The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 02
DocumentType
Test Method
Pages
35
ProductNote
ε2NOTE—Editorially corrected Table X6.1 in October 2020.
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 8147 : 2017 Standard Specification for Special-Purpose Test Fuels for Aviation Compression-Ignition Engines
ASTM D 7807 : 2020 Standard Test Method for Determination of Boiling Range Distribution of Hydrocarbon and Sulfur Components of Petroleum Distillates by Gas Chromatography and Chemiluminescence Detection
ASTM D 7798 : 2020 Standard Test Method for Boiling Range Distribution of Petroleum Distillates with Final Boiling Points up to 538 °C by Ultra Fast Gas Chromatography (UF GC)
ASTM D 396 : 2021 Standard Specification for Fuel Oils
ASTM D 4485 : 2020 Standard Specification for Performance of Active API Service Category Engine Oils
ASTM D 2549 : 2002 : R2017 Standard Test Method for Separation of Representative Aromatics and Nonaromatics Fractions of High-Boiling Oils by Elution Chromatography
ASTM D 6352 : 2019 : EDT 1 Standard Test Method for Boiling Range Distribution of Petroleum Distillates in Boiling Range from 174 °C to 700 °C by Gas Chromatography
ASTM D 6074 : 2015 Standard Guide for Characterizing Hydrocarbon Lubricant Base Oils
ASTM D 7223 : 2021 Standard Specification for Aviation Certification Turbine Fuel
ASTM D 5154/D5154M : 2018 Standard Test Method for Determining Activity and Selectivity of Fluid Catalytic Cracking (FCC) Catalysts by Microactivity Test
ASTM D 7964/D7964M : 2019 Standard Test Method for Determining Activity of Fluid Catalytic Cracking (FCC) Catalysts in a Fluidized Bed
ASTM D 975 : 2021 Standard Specification for Diesel Fuel
ASTM D 7566 : 2022 Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons
ASTM D 4924 : 2021 Standard Classification for Petroleum Waxes for Use in Rubber Compounding
ASTM D 7500 : 2015 : R2019 Standard Test Method for Determination of Boiling Range Distribution of Distillates and Lubricating Base Oils—in Boiling Range from 100 °C to 735 °C by Gas Chromatography
ASTM D 7665 : 2022 Standard Guide for Evaluation of Biodegradable Heat Transfer Fluids
ASTM D 7169 : 2020 : EDT 1 Standard Test Method for Boiling Point Distribution of Samples with Residues Such as Crude Oils and Atmospheric and Vacuum Residues by High Temperature Gas Chromatography
ASTM D 7863 : 2022 Standard Guide for Evaluation of Convective Heat Transfer Coefficient of Liquids
ASTM D 6417 : 2015 : R2019 Standard Test Method for Estimation of Engine Oil Volatility by Capillary Gas Chromatography
ASTM D 976 : 2021 Standard Test Method for Calculated Cetane Index of Distillate Fuels
ASTM D 3907/D3907M : 2019 Standard Test Method for Testing Fluid Catalytic Cracking (FCC) Catalysts by Microactivity Test
ASTM D 2892 : 2020 Standard Test Method for Distillation of Crude Petroleum (15-Theoretical Plate Column)
ASTM D 8144 : 2018 : EDT 1 Standard Test Method for Separation and Determination of Aromatics, Nonaromatics, and FAME Fractions in Middle Distillates by Solid-Phase Extraction and Gas Chromatography
ASTM D 7213 : 2015 : R2019 Standard Test Method for Boiling Range Distribution of Petroleum Distillates in the Boiling Range from 100 °C to 615 °C by Gas Chromatography
ASTM D 2226 : 1993 : R2018 Standard Classification for Various Types of Petroleum Oils for Rubber Compounding Use
ASTM D 4737 : 2021 Standard Test Method for Calculated Cetane Index by Four Variable Equation
ASTM D 3699 : 2019 Standard Specification for Kerosine
ASTM D 8046 : 2021 Standard Guide for Pumpability of Heat Transfer Fluids
ASTM D 1655 : 2022 Standard Specification for Aviation Turbine Fuels
ASTM D 6743 : 2020 Standard Test Method for Thermal Stability of Organic Heat Transfer Fluids
ASTM D 4054 : 2022 Standard Practice for Evaluation of New Aviation Turbine Fuels and Fuel Additives
ASTM D 3343 : 2016 Standard Test Method for Estimation of Hydrogen Content of Aviation Fuels
ASTM D 3338/D3338M : 2020 : REV A Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels
ASTM D 7215 : 2016 Standard Test Method for Calculated Flash Point from Simulated Distillation Analysis of Distillate Fuels
ASTM D 5372 : 2020 Standard Guide for Evaluation of Hydrocarbon Heat Transfer Fluids
ASTM D 5399 : 2009 : R2017 Standard Test Method for Boiling Point Distribution of Hydrocarbon Solvents by Gas Chromatography
ASTM D 7398 : 2021 Standard Test Method for Boiling Range Distribution of Fatty Acid Methyl Esters (FAME) in the Boiling Range from 100 °C to 615 °C by Gas Chromatography

ASTM E 516 : 1995 : REV A : R2013 Standard Practice for Testing Thermal Conductivity Detectors Used in Gas Chromatography
ASTM D 4057 : 2019 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 6300 : 2021 Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants
ASTM D 6300 : 2020 : REV B Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants
ASTM E 516 : 1995 : REV A : R2021 Standard Practice for Testing Thermal Conductivity Detectors Used in Gas Chromatography
ASTM E 355 : 1996 : R2021 : EDT 1 Standard Practice for Gas Chromatography Terms and Relationships
ASTM D 6708 : 2001 Standard Practice for Statistical Assessment and Improvement of the Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material
ASTM D 6708 : 2021 Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material
ASTM D 6300 : 1999 Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants
ASTM D 4057 : 2022 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM E 355 : 1996 : R2014 Standard Practice for Gas Chromatography Terms and Relationships
ASTM D 1160 : 2002 Standard Test Method for Distillation of Petroleum Products at Reduced Pressure
ASTM D 6708 : 2019 : REV A : EDT 1 Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material

View more information
US$108.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.