• ASTM D 2937 : 2000 : EDT 1

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    Standard Test Method for Density of Soil in Place by the Drive-Cylinder Method

    Available format(s):  Hardcopy, PDF

    Superseded date:  11-11-2014

    Language(s):  English

    Published date:  06-10-2000

    Publisher:  American Society for Testing and Materials

    Add to Watchlist

    Add To Cart

    Scope - (Show below) - (Hide below)

    1.1 This test method covers the determination of in-place density of soil by the drive-cylinder method. The test method involves obtaining a relatively undisturbed soil sample by driving a thin-walled cylinder and the subsequent activities for the determination of in-place density. When sampling or in-place density is required at depth, Test Method D1587 should be used.

    1.2 This test method is not appropriate for sampling organic soils which can compress upon sampling, very hard natural soils and heavily compacted soils which cannot be easily penetrated by the drive sampler, soils of low plasticity which will not be readily retained in the cylinder, or soils which contain appreciable amounts of gravel (particles coarser than 4.75 mm (3/16 in.)). The presence of particles coarser than 4.75 mm (3/16in.) may introduce significant errors in density measurements by causing voids along the wall of the cylinder during driving, and when coarse materials have to be dislodged by the trimming of the sample obtained by the cylinder.

    1.3 This test method is limited to the procedures necessary for obtaining specimens suitable for determining the in-place density and water content of certain soils. The procedures and precautions necessary for selecting locations and obtaining undisturbed samples suitable for laboratory testing or otherwise determining engineering properties is beyond the scope of this test method.

    1.4 It is common practice in the engineering profession to concurrently use pounds to represent both a unit of mass (lbm) and a unit of force (lbf). This implicitly combines two separate systems of units, that is, the absolute system and the gravitational system. It is scientifically undesirable to combine the use of two separate sets of inch-pound units within a single standard. This test method has been written using the gravitational system of units when dealing with the inch-pound system. In this system the pound (lbf) represents a unit of force (weight). However, the use of balances or scales recording pounds of mass (lbm), or the recording of density in lbm/ft 3 should not be regarded as nonconformance with this test method.

    1.5 The standard values stated in SI units are to be regarded as the standard. The values in parentheses are provided for information purposes only.

    1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    General Product Information - (Show below) - (Hide below)

    Committee D 18
    Document Type Test Method
    Publisher American Society for Testing and Materials
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    ASTM A 807/A807M : 2017 Standard Practice for Installing Corrugated Steel Structural Plate Pipe for Sewers and Other Applications
    ASTM D 5874 : 2016 Standard Test Methods for Determination of the Impact Value (IV) of a Soil
    ASTM E 3163 : 2018 Standard Guide for Selection and Application of Analytical Methods and Procedures Used during Sediment Corrective Action
    ASTM D 6031/D6031M : 1996 : R2015 Standard Test Method for Logging In Situ Moisture Content and Density of Soil and Rock by the Nuclear Method in Horizontal, Slanted, and Vertical Access Tubes
    ASTM D 8152 : 2018 Standard Practice for Measuring Field Infiltration Rate and Calculating Field Hydraulic Conductivity Using the Modified Philip Dunne Infiltrometer Test
    ASTM D 5195 : 2014 Standard Test Method for Density of Soil and Rock In-Place at Depths Below Surface by Nuclear Methods
    ASTM B 788/B788M : 2009 : R2014 Standard Practice for Installing Factory-Made Corrugated Aluminum Culverts and Storm Sewer Pipe
    ASTM B 790/B790M : 2016 Standard Practice for Structural Design of Corrugated Aluminum Pipe, Pipe-Arches, and Arches for Culverts, Storm Sewers, and Other Buried Conduits
    ASTM D 4220/D4220M : 2014 Standard Practices for Preserving and Transporting Soil Samples
    ASTM B 789/B789M : 2016 Standard Practice for Installing Corrugated Aluminum Structural Plate Pipe for Culverts and Sewers
    ASTM D 5220 : 2014 Standard Test Method for Water Mass per Unit Volume of Soil and Rock In-Place by the Neutron Depth Probe Method
    ASTM D 6391 : 2011 Standard Test Method for Field Measurement of Hydraulic Conductivity Using Borehole Infiltration
    ASTM D 6938 : 2017 : REV A Standard Test Methods for In-Place Density and Water Content of Soil and Soil-Aggregate by Nuclear Methods (Shallow Depth)
    ASTM D 7830/D7830M : 2014 Standard Test Method for In-Place Density (Unit Weight) and Water Content of Soil Using an Electromagnetic Soil Density Gauge
    ASTM D 5080 : 2017 Standard Test Method for Rapid Determination of Percent Compaction
    ASTM A 796/A796M : 2017 : REV A Standard Practice for Structural Design of Corrugated Steel Pipe, Pipe-Arches, and Arches for Storm and Sanitary Sewers and Other Buried Applications
    ASTM A 798/A798M : 2017 Standard Practice for Installing Factory-Made Corrugated Steel Pipe for Sewers and Other Applications
    ASTM D 7015/D7015M : 2018 Standard Practices for Obtaining Intact Block (Cubical and Cylindrical) Samples of Soils
    ASTM E 2060 : 2006 : R2014 Standard Guide for Use of Coal Combustion Products for Solidification/Stabilization of Inorganic Wastes
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective