• There are no items in your cart

ASTM D 3294 : 2015

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Polytetrafluoroethylene (PTFE) Resin Molded Sheet and Molded Basic Shapes
Available format(s)

Hardcopy , PDF

Superseded date

07-25-2022

Language(s)

English

Published date

09-10-2015

1.1This specification establishes requirements and methods of test for the material, dimensions, and workmanship, and the physical and electrical properties of molded sheet in minimum thicknesses of 0.794 mm (1/32in.) manufactured from PTFE resin molding materials defined in Specification D4894.

1.2This specification also establishes requirements for molded basic shapes made from molding materials. This specification is for products 300 mm (12 in.) or less in a dimension parallel to and 12.7 mm (0.5 in.) or greater in the dimension perpendicular to the direction of the applied molding pressure.

1.3The values stated in SI units are to be regarded as the standard.

1.4The following precautionary caveat pertains only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Special attention is called to 13.2, 13.3, 13.6, 13.8, and A1.

Note 1:There is no known ISO equivalent to this standard.

Committee
D 20
DocumentType
Standard
Pages
6
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM F 754 : 2008 : R2015 Standard Specification for Implantable Polytetrafluoroethylene (PTFE) Sheet, Tube, and Rod Shapes Fabricated from Granular Molding Powders
ASTM F 336 : 2002 : R2016 Standard Practice for Design and Construction of Nonmetallic Enveloped Gaskets for Corrosive Service
ASTM F 1511 : 2018 Standard Specification for Mechanical Seals for Shipboard Pump Applications

ASTM D 1600 : 1999 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 1708 : 1996 Standard Test Method for Tensile Properties of Plastics By Use of Microtensile Specimens
ASTM D 5947 : 1996 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
ASTM D 1708 : 2006 : REV A Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens
ASTM D 3892 : 2015 : R2020 Standard Practice for Packaging/Packing of Plastics
ASTM D 4894 : 1998 : REV A Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials
ASTM D 5947 : 2002 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
ASTM D 4894 : 2007 Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials
ASTM D 3892 : 1993 : R2003 Standard Practice for Packaging/Packing of Plastics
ASTM D 3892 : 2015 Standard Practice for Packaging/Packing of Plastics
ASTM D 1708 : 2002 Standard Test Method for Tensile Properties of Plastics By Use of Microtensile Specimens
ASTM D 1708 : 2006 Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens
ASTM D 5947 : 2011 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
ASTM D 5947 : 2018 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
ASTM D 3892 : 1993 : R1998 Standard Practice for Packaging/Packing of Plastics
ASTM D 1600 : 2007 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 1600 : 2013 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 1600 : 2014 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 4591 : 2001 Standard Test Method for Determining Temperatures and Heats of Transitions of Fluoropolymers by Differential Scanning Calorimetry
ASTM D 4591 : 2007 Standard Test Method for Determining Temperatures and Heats of Transitions of Fluoropolymers by Differential Scanning Calorimetry
ASTM D 1600 : 2008 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 4591 : 2007 : R2012 Standard Test Method for Determining Temperatures and Heats of Transitions of Fluoropolymers by Differential Scanning Calorimetry
ASTM D 5947 : 2006 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
ASTM D 4591 : 1997 Standard Test Method for Determining Temperatures and Heats of Transitions of Fluoropolymers by Differential Scanning Calorimetry
ASTM D 4591 : 2017 Standard Test Method for Determining Temperatures and Heats of Transitions of Fluoropolymers by Differential Scanning Calorimetry
ASTM D 4894 : 2004 Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials
ASTM D 1600 : 2018 Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
ASTM D 618 : 2013 Standard Practice for Conditioning Plastics for Testing
ASTM D 5947 : 2003 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
ASTM D 5947 : 2001 : EDT 1 Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
ASTM D 1708 : 2013 Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens
ASTM D 4894 : 2015 Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials
ASTM D 1708 : 2010 Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens
ASTM D 4894 : 2019 Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials
ASTM D 4894 : 2007 : R2012 Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials
ASTM D 3892 : 1993 : R2009 Standard Practice for Packaging/Packing of Plastics
ASTM D 1708 : 2002 : REV A Standard Test Method for Tensile Properties of Plastics By Use of Microtensile Specimens
ASTM D 1708 : 2018 Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens
ASTM D 618 : 2021 Standard Practice for Conditioning Plastics for Testing
ASTM D 4591 : 2022 Standard Test Method for Determining Temperatures and Heats of Transitions of Fluoropolymers by Differential Scanning Calorimetry

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.