• There are no items in your cart

ASTM D 3338/D3338M : 2009

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels
Available format(s)

Hardcopy , PDF

Superseded date

11-11-2014

Language(s)

English

Published date

04-15-2009

CONTAINED IN VOL. 05.02, 2015 Describes the estimation of the net heat of combustion (megajoules per kilogram or [Btu per pound]) of aviation gasolines and aircraft turbine and jet engine fuels in the range from 40.19 to 44.73 megajoules per kilogram or [17280 to 19230 Btu per pound].

1.1 This test method covers the estimation of the net heat of combustion (megajoules per kilogram or [Btu per pound]) of aviation gasolines and aircraft turbine and jet engine fuels in the range from 40.19 to 44.73 megajoules per kilogram or [17 280 to 19 230 Btu per pound]. The precision for estimation of the net heat of combustion outside this range has not been determined for this test method.

1.2 This test method is purely empirical and is applicable to liquid hydrocarbon fuels that conform to the specifications for aviation gasolines or aircraft turbine and jet engine fuels of grades Jet A, Jet A-1, Jet B, JP-4, JP-5, JP-7, and JP-8.

Note 1—The experimental data on heat of combustion from which the Test Method D 3338 correlation was devised was obtained by a precision method similar to Test Method D 4809.

Note 2—The estimation of the net heat of combustion of a hydrocarbon fuel is justifiable only when the fuel belongs to a well-defined class for which a relation between heat of combustion and aromatic and sulfur contents, density, and distillation range of the fuel has been derived from accurate experimental measurements on representative samples of that class. Even in this case, the possibility that the estimates may be in error by large amounts for individual fuels should be recognized. The fuels used to establish the correlation presented in this method are defined as follows:

Fuels:
Aviation gasolineGrades 100/130 and 115/145 (1, 2)
Kerosines, alkylates, and special WADC fuels (3)
Pure hydrocarbonsparaffins, naphthenes, and aromatics (4)
Fuels for which data were reported by the Coordinating Research Council (5).

Note 3—The property ranges used in this correlation are as follows:

Aromaticsfrom 0 to 100 mass %
API Gravityfrom [25.7 to 81.2°API]
Volatilityfrom [160 to 540°F], average boiling point

1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.3.1 Although the test method permits the calculation of net heat of combustion in either SI or inch-pound units, SI units are the preferred units.

1.3.2 The net heat of combustion can also be estimated in inch-pound units by Test Method D 1405 or in SI units by Test Method D 4529. Test Method D 1405 requires calculation of one of four equations dependent on the fuel type with a precision equivalent to that of this test method. Test Method D 4529 requires calculation of a single equation for all aviation fuels with a precision equivalent to that of this test method. Unlike Test Method D 1405 and D 4529, Test Method D 3338 does not require the use of aniline point.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
D 02
DevelopmentNote
Supersedes ASTM D 3338. (05/2009)
DocumentType
Test Method
Pages
5
ProductNote
Reconfirmed 2009
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ISO 15550:2016 Internal combustion engines Determination and method for the measurement of engine power General requirements

ASTM D 86 : 2017-06 TEST METHOD FOR DISTILLATION OF PETROLEUM PRODUCTS AND LIQUID FUELS AT ATMOSPHERIC PRESSURE
ASTM D 4529 : 2017 : REDLINE Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels
ASTM D 6379 : 2011 : REDLINE TEST METHOD FOR DETERMINATION OF AROMATIC HYDROCARBON TYPES IN AVIATION FUELS AND PETROLEUM DISTILLATES - HIGH PERFORMANCE LIQUID CHROMATOGRAPHY METHOD WITH REFRACTIVE INDEX DETECTION
ASTM D 240 : 2017 : REDLINE Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter
ASTM D 2622 : 2016 : REDLINE Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry

View more information
US$66.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.