ASTM D 3485 : 2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Specification for Coilable High Density Polyethylene (HDPE) Cable in Conduit (CIC)
Hardcopy , PDF
07-29-2022
English
05-05-2015
CONTAINED IN VOL. 08.04, 2017 Defines cable in conduit (CIC), which is a smooth-walled, coilable, high-density polyethylene (HDPE) conduit (duct) that contains preassembled wires and cables.
1.1This specification covers cable in conduit (CIC), which is a smooth-walled, coilable, high-density polyethylene (HDPE) conduit (duct) that contains preassembled wires and cables. The outside diameter of the conduit is controlled and the wire or cable encased within may be comprised of single or multiple configurations consisting of electrical/power wires or cables, fiber optic, traditional copper communication, coaxial cable, or any combination thereof. CIC configurations are preassembled into the conduit during the extrusion process and in industry-specific designs for use in commercial, industrial, transportation, government, and utility applications
1.2This specification does not attempt to identify every possible preassembled conduit/cable configuration but is intended to identify material and minimum assembled product properties for optimizing reliability and service life.
1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
Note 1:Whenever two sets of values are presented, in different units, the imperial units are the standard, while those in the parentheses (metric unites) are provided for informational purposes.
Note 2:End users may elect to field install single or multiple wire or cable configurations into field-installed conduit. In the case where polyethylene conduit is to have the wire or cable configurations field installed, then the more appropriate specifications to select for establishing the conduit’s material, dimensional, workmanship, and property tests would be Specification F2160 or NEMA TC-7.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| Committee |
F 17
|
| DocumentType |
Standard
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| AASHTO R 63 : 2013 | PRACTICE FOR SOLID WALL HIGH-DENSITY POLYETHYLENE (HDPE) CONDUIT FOR NON-PRESSURE APPLICATIONS USED FOR THE PROTECTION OF POWER AND TELECOMMUNICATIONS CABLES |
| ASTM D 1600 : 1999 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1238 : 2000 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D 1238 : 2004 : REV C | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D 1693 : 2000 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM D 2122 : 1998 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 618 : 2013 : REDLINE | Standard Practice for Conditioning Plastics for Testing |
| ASTM F 412 : 2020 : REV A | Standard Terminology Relating to Plastic Piping Systems |
| ASTM F 412 : 2021 | Standard Terminology Relating to Plastic Piping Systems |
| ASTM F 2160 : 2022 | Standard Specification for Solid Wall High Density Polyethylene (HDPE) Conduit Based on Controlled Outside Diameter (OD) |
| ASTM D 2444 : 1999 : R2010 | Standard Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight) |
| ASTM D 2444 : 2019 | Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight) |
| ASTM D 1238 : 2013 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D 2444 : 2017 | Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight) |
| ASTM D 1238 : 2010 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D 2412 : 2011 | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
| ASTM D 3350 : 2000 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 2412 : 2002 : R2008 | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
| ASTM D 3350 : 2008 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 4883 : 2003 | Standard Test Method for Density of Polyethylene by the Ultrasound Technique |
| ASTM D 1693 : 2008 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM D 1238 : 2013 : REDLINE | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D 3350 : 2021 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 2412 : 2010 : REV A | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
| ASTM D 3350 : 2002 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 1505 : 2003 | Standard Test Method for Density of Plastics by the Density-Gradient Technique |
| ASTM D 1600 : 2007 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 792 : 2013 : REDLINE | Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement |
| ASTM D 1600 : 2013 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1693 : 2015 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM D 1693 : 2012 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM D 3350 : 2014 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 1693 : 1994 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM F 2160 : 2008 | Standard Specification for Solid Wall High Density Polyethylene (HDPE) Conduit Based on Controlled Outside Diameter (OD) |
| ASTM D 2444 : 2021 | Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight) |
| ASTM D 1600 : 2014 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1600 : 2008 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 2412 : 1996 : REV A | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
| ASTM D 3350 : 2004 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 3350 : 2002 : REV A | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 1693 : 2021 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM D 3350 : 2012 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM F 2160 : 2010 | Standard Specification for Solid Wall High Density Polyethylene (HDPE) Conduit Based on Controlled Outside Diameter (OD) |
| ASTM D 3350 : 2001 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM F 2160 : 2001 | Standard Specification for Solid Wall High Density Polyethylene (HDPE) Conduit Based on Controlled Outside Diameter (OD) |
| ASTM D 2412 : 2002 | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
| ASTM D 3350 : 2012 : EDT 1 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 2122 : 1998 : EDT 1 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 1693 : 2005 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM D 638 : 2014 | Standard Test Method for Tensile Properties of Plastics |
| ASTM D 1238 : 2004 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D 2444 : 1999 | Standard Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight) |
| ASTM D 1505 : 1968 : R1979 | Standard Test Method for Density Of Plastics By The Density-Gradient Technique |
| ASTM D 2412 : 2021 | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
| NFPA 70 : 2017 | NATIONAL ELECTRICAL CODE |
| ASTM D 790 : 2017 : REDLINE | Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials |
| ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
| ASTM D 3350 : 2010 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 618 : 2013 | Standard Practice for Conditioning Plastics for Testing |
| ASTM F 2160 : 2016 | Standard Specification for Solid Wall High Density Polyethylene (HDPE) Conduit Based on Controlled Outside Diameter (OD) |
| ASTM D 2122 : 2016 : REDLINE | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 1693 : 2007 : REV A | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM D 1505 : 2010 | Standard Test Method for Density of Plastics by the Density-Gradient Technique |
| ASTM D 2444 : 1999 : R2005 | Standard Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight) |
| ASTM D 3350 : 2006 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| UL 1990:3ED 2013-11 | Standard for Nonmetallic Underground Conduit with Conductors |
| ASTM D 1505 : 2018 | Standard Test Method for Density of Plastics by the Density-Gradient Technique |
| ASTM D 2122 : 1998 : R2004 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 3350 : 2010 : REV A | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 1505 : 1998 : EDT 1 | Standard Test Method for Density of Plastics by the Density-Gradient Technique |
| ASTM D 2122 : 2016 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 4883 : 2008 | Standard Test Method for Density of Polyethylene by the Ultrasound Technique (Withdrawn 2017) |
| ASTM D 3350 : 2014 : REDLINE | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| NEMA TC 7 : 2016 | SMOOTH-WALL COILABLE ELECTRICAL POLYETHYLENE CONDUIT |
| ASTM D 1238 : 2001 : EDT 1 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D 4883 : 1999 | Standard Test Method for Density of Polyethylene by the Ultrasound Technique |
| ASTM D 1693 : 2015 : EDT 1 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM D 1238 : 2004 : REV A | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D 1693 : 2001 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM D 1693 : 2013 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM D 2412 : 2011 : R2018 | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
| ASTM D 2122 : 1998 : R2010 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM F 2160 : 2005 | Standard Specification for Solid Wall High Density Polyethylene (HDPE) Conduit Based on Controlled Outside Diameter (OD) |
| ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
| ASTM D 1238 : 1985 | Standard Test Method for Flow Rates of Thermoplastics by Extrusion Plastometer |
| ASTM D 618 : 2021 | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 2412 : 2010 | Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
| ASTM D 3350 : 2005 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 2122 : 2015 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 1693 : 2015 : REDLINE | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM D 638 : 2022 | Standard Test Method for Tensile Properties of Plastics |
| ASTM D 4883 : 2018 | Standard Test Method for Density of Polyethylene by the Ultrasound Technique |
| ASTM D 1693 : 2007 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.