• There are no items in your cart

ASTM D 350 : 2013 : REDLINE

Current
Current

The latest, up-to-date edition.

Standard Test Methods for Flexible Treated Sleeving Used for Electrical Insulation
Available format(s)

PDF

Language(s)

English

Published date

11-01-2013

CONTAINED IN VOL. 10.01, 2015 Defines procedures for testing electrical insulating sleeving comprising a flexible tubular product made from a woven textile fibre base, such as cotton, rayon, nylon, or glass, thereafter impregnated, or coated, or impregnated and coated, with a suitable dielectric material.

1.1These test methods cover procedures for testing electrical insulating sleeving comprising a flexible tubular product made from a woven textile fibre base, such as cotton, rayon, nylon, or glass, thereafter impregnated, or coated, or impregnated and coated, with a suitable dielectric material.

1.2The procedures appear in the following sections:

Procedures

Sections

Brittleness Temperature

18 to 21

Compatibility of Sleeving with Magnet Wire Insulation

45 to 59

Conditioning

6

Dielectric Breakdown Voltage

12 to 17

Dielectric Breakdown Voltage After Short-Time Aging

29 to 33

Dimensions

7 to 11

Effect of Push-Back After Heat Aging

73 to 78

Flammability

22 to 28

Hydrolytic Stability

66 to 72

Oil Resistance

34 to 37

Selection of Test Material

5

Solvent Resistance

60 to 65

Thermal Endurance

38 to 44


1.3The values stated in inch-pound units, except for °C, are to be regarded as the standard. The values in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4This is a fire-test-response standard. See Sections 22 through 28, which are the procedures for flammability tests.

1.5This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products or assemblies under actual fire conditions.

1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see 45.2 and 63.1.1.

Note 1This standard resembles IEC 60684-2, Specification for Flexible Insulating Sleeving—Part 2 Methods of Test, in a number of ways, but is not consistently similar throughout. The data obtained using either standard are not necessarily technically equivalent.

1.7Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.

Committee
D 09
DocumentType
Redline
Pages
14
PublisherName
American Society for Testing and Materials
Status
Current

ASTM D 581/D581M : 2012 : REDLINE Standard Specification for Glass Fiber Greige Braided Tubular Sleeving
ASTM D 372 : 2000 Standard Specification for Flexible Treated Sleeving Used for Electrical Insulation
CSA C22.2 No. 198.3 : 2005 : R2014 COATED ELECTRICAL SLEEVING
CSA C22.2 No. 198.3 : 2005 : R2010 COATED ELECTRICAL SLEEVING
CSA C22.2 No. 198.3:2005 COATED ELECTRICAL SLEEVING
MIL-I-3190 Revision F:1991 INSULATION SLEEVING, ELECTRICAL, FLEXIBLE, COATED, GENERAL SPECIFICATION FOR
ASTM D 372 : 2000 : R2006 Standard Specification for Flexible Treated Sleeving Used for Electrical Insulation (Withdrawn 2012)
SAE AIR 4567 : 2014 COMPOSITE ELECTRICAL CONNECTORS
ASTM E 1420 : 1991 Practice for Specifying Polymeric Materials for Service in Ionizing Radiation Environments (Withdrawn 1996)

IEC 60684-2:2011 Flexible insulating sleeving - Part 2: Methods of test
ASTM D 1711 : 2015 : REDLINE Standard Terminology Relating to Electrical Insulation
ISO 13943:2017 Fire safety — Vocabulary
IEEE 101 : 1987 GUIDE FOR THE STATISTICAL ANALYSIS OF THERMAL LIFE TEST DATA
ASTM D 876 : 2013 : REDLINE Standard Test Methods for Nonrigid Vinyl Chloride Polymer Tubing Used for Electrical Insulation
ASTM D 471 : 2016-02 TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS
ASTM D 374 : 1999 Standard Test Methods for Thickness of Solid Electrical Insulation
ASTM D 746 : 2014 : REDLINE Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact
ASTM D 5423 : 2014 Standard Specification for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.