Customer Support: +1 416-401-8730

Login to i2i Subscription Intertek.com
  • There are no items in your cart
Please enter a keyword to search
Advanced search

ASTM D 3641 : 2015 : REDLINE

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
Available format(s)

PDF

Superseded date

05-29-2021

Language(s)

English

Published date

06-30-2015

Publisher

American Society for Testing and Materials

CONTAINED IN VOL. 08.02, 2015 Defines the general principles to be followed when injection molding test specimens of thermoplastic molding and extrusion materials.

1.1This practice covers the general principles to be followed when injection molding test specimens of thermoplastic molding and extrusion materials. This practice is to be used to obtain uniformity in methods of describing the various steps of the injection molding process and to set up uniform methods of reporting these conditions. The exact conditions required to prepare suitable specimens will vary for each plastic material. Any requirements or recommendations in the material specification that differ from this standard take precedence over those in this standard. Always consult the referenced material document for specimen preparation. If no referenced document exists, then consult the material supplier for specimen preparation guidance and note such in the test report.

1.2The methodology presented assumes the use of reciprocating screw injection molding machines.

1.3The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1:This practice is equivalent to the following parts of ISO 294: Plastics—Injection Moulding of Test Specimens of Thermoplastic Materials; 294-1: Part 1—General Principles and Multipurpose Test Specimens (ISO Type A Mould) and Bars (ISO Type B Mould); ISO 294-2: Part 2—Small Tensile Bars (ISO Type C Mould); ISO 294-3: Part 3—Plates (ISO Type D Moulds).

Committee
D 20
DevelopmentNote
Supersedes ASTM D 647. (02/2002)
DocumentType
Redline
Pages
11
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

ASTM D 6835 : 2017 : REDLINE Standard Classification System for Thermoplastic Elastomer-Ether-Ester Molding and Extrusion Materials (TEEE)
ASTM D 4673 : 2016 : REDLINE Standard Classification System for and Basis for Specification for Acrylonitrile–Butadiene–Styrene (ABS) Plastics and Alloys Molding and Extrusion Materials
ASTM D 5592 : 1994 Standard Guide for Material Properties Needed in Engineering Design Using Plastics
ASTM D 5939 : 1996 Standard Test Method for Injection Moulding of Test Specimens of Thermoplatic Materials (Withdrawn 1998)
ASTM D 788 : 2016 : REDLINE Standard Classification System for Poly(Methyl Methacrylate) (PMMA) Molding and Extrusion Compounds
SAE J 2749 : 2017 HIGH STRAIN RATE TENSILE TESTING OF POLYMERS
ASTM D 955 : 2008 Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics
(INACTIVE RECORD)ASTM D 5336 : 2015-04 CLASSIFICATION SYSTEM AND BASIS FOR SPECIFICATION FOR POLYPHTHALAMIDE (PPA) INJECTION MOLDING MATERIALS
ASTM D 4067 : 2016 : REDLINE Standard Classification System and Basis for Specification for Reinforced and Filled Poly(Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ASTM Methods
ASTM D 5204 : 2017 : REDLINE CLASSIFICATION SYSTEM FOR POLYAMIDE-IMIDE (PAI) MOLDING AND EXTRUSION MATERIALS
ASTM D 5676 : 1999 Standard Specification for Recycled Polystyrene Molding and Extrusion Materials (Withdrawn 2004)
ASTM D 4066 : 2013 Standard Classification System for Nylon Injection and Extrusion Materials (PA)
ASTM D 3965 : 2016 : REDLINE Standard Classification System and Basis for Specifications for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for Pipe and Fittings
ASTM D 6394 : 2014 : REDLINE Standard Specification for Sulfone Plastics (SP)
ASTM D 787 : 2012-08 SPECIFICATION FOR ETHYL CELLULOSE MOLDING AND EXTRUSION COMPOUNDS
ASTM D 4634 : 2016 : REDLINE Standard Classification System and Basis for Specification for Styrene-Maleic Anhydride Molding and Extrusion Materials (S/MA)
ASTM F 2617 : 2015 : REDLINE Standard Test Method for Identification and Quantification of Chromium, Bromine, Cadmium, Mercury, and Lead in Polymeric Material Using Energy Dispersive X-ray Spectrometry
ASTM D 5592 : 1994 : R2002 : EDT 1 Standard Guide for Material Properties Needed in Engineering Design Using Plastics
ASTM D 5593 : 1999 : EDT 1 Standard Classification for Thermoplastic Elastomers-Olefinic (TEO) (Withdrawn 2005)
ASTM D 4203 : 2017 : REDLINE Standard Specification for and Basis for Specifications for Styrene-Acrylonitrile (SAN) Injection and Extrusion Materials
ASTM D 6339 : 2011 Standard Classification System for and Basis for Specifications for Syndiotactic Polystyrene Molding and Extrusion (SPS)
ASTM D 5205 : 2016 : REDLINE Standard Classification System and Basis for Specification for Polyetherimide (PEI) Materials
ASTM D 1562 : 2015 : REDLINE Standard Classification System and Basis for Specification for Cellulose Acetate Propionate Molding and Extrusion Compounds (CAP)
ASTM D 707 : 2015 : REDLINE Standard Classification System and Basis for Specification for Cellulose Acetate Butyrate Molding and Extrusion Compounds (CAB)
ASTM D 5592 : 1994 : R2010 Standard Guide for Material Properties Needed in Engineering Design Using Plastics
ASTM D 5021 : 2000 Standard Specification for Thermoplastic Elastomer-Chlorinated Ethylene Alloy (TECEA) (Withdrawn 2007)
ASTM D 5138 : 2016 : REDLINE Standard Classification System and Basis for Specification for Liquid Crystal Polymers Molding and Extrusion Materials (LCP)
ASTM D 955 : 2008 : R2014 Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics
ASTM D 706 : 2015 : REDLINE Standard Classification System and Basis for Specifications for Cellulose Acetate Molding and Extrusion Compounds (CA)
ASTM D 5990 : 2000 Standard Classification System for Polyketone Injection Molding and Extrusion Materials (PK) (Withdrawn 2007)
ASTM D 8033 : 2016 Standard Classification System for Poly(Ether Ether Ketone) (PEEK) Molding and Extrusion Materials

ASTM D 957 : 2012 : REDLINE Standard Practice for Determining Surface Temperature of Molds for Plastics
ISO 294-3:2002 Plastics Injection moulding of test specimens of thermoplastic materials Part 3: Small plates
ASTM D 1525 : 2017 Standard Test Method for Vicat Softening Temperature of Plastics
ISO 294-2:1996 Plastics Injection moulding of test specimens of thermoplastic materials Part 2: Small tensile bars
ASTM D 790 : 2017 : REDLINE Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
ASTM D 648 : 2016 Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position
ISO 294-1:2017 Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens
ISO 20753:2008 Plastics Test specimens
ASTM D 570 : 1998 : R2018 Standard Test Method for Water Absorption of Plastics
ASTM D 638 : 2014 : REDLINE Standard Test Method for Tensile Properties of Plastics

View more information
US$75.00
Excluding Tax where applicable
USD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us