• ASTM D 4066 : 1994 : REV B

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    Standard Classification System for Nylon Injection and Extrusion Materials (PA)

    Available format(s):  Hardcopy, PDF

    Superseded date:  11-11-2014

    Language(s):  English

    Published date:  01-15-1994

    Publisher:  American Society for Testing and Materials

    Add to Watchlist

    Add To Cart

    Scope - (Show below) - (Hide below)

    1.1 This specification covers nylon materials suitable for injection molding and extrusion. Some of these compositions are also suitable for compression molding and application from solution.

    1.2 The properties included in this specification are those required to identify the compositions covered. There may be other requirements necessary to identify particular characteristics important to specialized applications. These shall be agreed upon between the user and the supplier, by using the suffixes as given in Section 5.

    1.3 The values stated in SI units are to be regarded as the standard.

    1.4 The following safety hazards caveat pertains only to the test methods portion, Section 11, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. A specific hazards statement is given in 11.2. ^REFERENCE:

    ASTM Standards:

    D 149 Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies

    D 150 Test Methods for A-C Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulating Materials

    D 256 Test Methods for Impact Resistance of Plastics and Electrical Insulating Materials

    D 257 Test Methods for D-C Resistance or Conductance of Insulating Materials

    D 618 Practice for Conditioning Plastics and Electrical Insulating Materials for Testing

    D 638 Test Method for Tensile Properties of Plastics

    D 648 Test Method for Deflection Temperature of Plastics Under Flexural Load

    D 789 Test Methods for Determination of Relative Viscosity, Meting Point, and Moisture Content of Polyamide (PA)

    D 790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials

    D 792 Test Methods for Density and Specific Gravity (Relative Density) and Density of Plastics by Displacement

    D 883 Terminology Relating to Plastics

    D 1600 Terminology for Abbreviated Terms Relating to Plastics

    D 1897 Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials

    D 1898 Practice for Sampling of Plastics

    D 2584 Test Method for Ignition Loss of Cured Reinforced Resins

    D 3418 Test Method for Transition Temperatures of Polymers by Thermal Analysis

    D 3892 Practice for Packaging/Packing of Plastics

    D 4000 Classification System for Specifying Plastic Materials

    E 29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

    Military and Federal Specifications and Standards:

    MIL-STD-105 Sampling Procedure and Tables for Inspection by Attributes

    L-P-410 Plastic, Polyamide (Nylon) Rigid: Rods, Tubes, Flats, Molded and Cast Parts

    VV-I-530 Insulating Oil, Electrical (for Transformers, Switches, and Circuit Breakers)

    Underwriters Laboratories:

    UL 94 Standards for Tests for Flammability for Parts in Devices and Appliances

    ISO Standard:

    ISO 307 Determination of Viscosity Number of Polyamides in Dilute Solutions

    General Product Information - (Show below) - (Hide below)

    Committee D 20
    Document Type Standard
    Publisher American Society for Testing and Materials
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    ASTM D 6068 : 2010 : R2018 Standard Test Method for Determining J-R Curves of Plastic Materials
    ASTM F 1837M : 1997 : R2018 Standard Specification for Heat-Shrink Cable Entry Seals (Metric)
    ASTM F 2767 : 2018 Standard Specification for Electrofusion Type Polyamide-12 Fittings for Outside Diameter Controlled Polyamide-12 Pipe and Tubing for Gas Distribution
    ASTM D 6110 : 2018 Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics
    ASTM D 638 : 2014 Standard Test Method for Tensile Properties of Plastics
    ASTM D 5420 : 2016 Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact)
    ASTM D 4967 : 1999 : R2013 Standard Guide for Selecting Materials to Be Used for Insulation, Jacketing and Strength Components in Fiber-Optic Cables
    ASTM F 1836M : 2015 : R2019 Standard Specification for Stuffing Tubes, Nylon, and Packing Assemblies (Metric)
    ASTM D 4000 : 2016 Standard Classification System for Specifying Plastic Materials
    ASTM F 1733 : 2013 Standard Specification for Butt Heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing
    ASTM D 256 : 2010 : R2018 Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
    ASTM F 2945 : 2018 Standard Specification for Polyamide 11 Gas Pressure Pipe, Tubing, and Fittings
    ASTM D 4054 : 2019 Standard Practice for Evaluation of New Aviation Turbine Fuels and Fuel Additives
    ASTM G 175 : 2013 Standard Test Method for Evaluating the Ignition Sensitivity and Fault Tolerance of Oxygen Pressure Regulators Used for Medical and Emergency Applications
    ASTM D 955 : 2008 : R2014 Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective