• There are no items in your cart

ASTM D 4101 : 2000

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Polypropylene Injection and Extrusion Materials
Available format(s)

Hardcopy , PDF

Superseded date

11-11-2014

Language(s)

English

Published date

03-10-2002

1.1 This specification covers propylene plastic materials suitable for injection molding and extrusion. Polymers consist of propylene homopolymer, propylene copolymers, and propylene-elastomer compounded with or without the addition of impact modifiers (ethylene-propylene rubber, polyisobutylene rubber, and butyl rubber), colorants, stabilizers, lubricants, or reinforcements.

1.2 This specification allows for the use of those propylene plastic materials that can be recycled, reconstituted, and reground, provided that: (1) the requirements as stated in this specification are met, and (2) the material has not been modified in any way to alter its conformance to food contact regulations or similar requirements. The proportions of recycled, reconstituted, and reground material used, as well as the nature and the amount of any contaminant, cannot be practically covered in this specification. It is the responsibility of the supplier and the buyer of recycled, reconstituted, and reground materials to ensure compliance. (See Guide D5033.)

1.3 The values stated in SI units are to be regarded as the standard.

Note 1—The properties included in this specification are those required to identify the compositions covered. There may be other requirements necessary to identify particular characteristics important to specific applications. These will be designated by using the suffixes given in Section 1.

1.4 The following safety hazards caveat pertains only to the test methods portion, Section 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 2—There is no similar or equivalent ISO standard.

Committee
D 20
DocumentType
Standard
Pages
16
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM F 2881/F2881M : 2019 Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications
ASTM D 3012 : 2019 Standard Test Method for Thermal-Oxidative Stability of Polypropylene Using a Specimen Rotator Within an Oven
ASTM D 7254 : 2017 Standard Specification for Polypropylene (PP) Siding
ASTM F 2764/F2764M : 2019 Standard Specification for 6 to 60 in. [150 to 1500 mm] Polypropylene (PP) Corrugated Double and Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications
ASTM F 1545 : 2015 : REV A Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges
ASTM F 3371 : 2019 Standard Specification for Polyolefin Pipe and Fittings for Drainage, Waste, and Vent Applications
ASTM D 2673 : 2014 Standard Specification for Oriented Polypropylene Film
ASTM F 2830 : 2011 : R2017 Standard Specification for Manufacture and Joining of Polyethylene (PE) Gas Pressure Pipe With a Peelable Polypropylene (PP) Outer Layer
ASTM D 3218 : 2007 : R2018 Standard Specification for Polyolefin Monofilaments
ASTM F 2418 : 2016 : REV A Standard Specification for Polypropylene (PP) Corrugated Wall Stormwater Collection Chambers
ASTM F 1412 : 2016 Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems
ASTM F 2389 : 2017 : REV A Standard Specification for Pressure-rated Polypropylene (PP) Piping Systems
ASTM E 2952 : 2017 Standard Specification for Air-Purifying Respiratory Protective Smoke Escape Devices (RPED)
ASTM D 4967 : 1999 : R2013 Standard Guide for Selecting Materials to Be Used for Insulation, Jacketing and Strength Components in Fiber-Optic Cables
ASTM D 4000 : 2016 Standard Classification System for Specifying Plastic Materials
ASTM D 790 : 2017 Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
ASTM F 409 : 2017 Standard Specification for Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings
ASTM F 3219 : 2019 Standard Specification for 3 to 30 in. (75 To 750 mm) Polypropylene (PP) Corrugated Single Wall Pipe and Fittings
ASME A112.36.2/CSA B79.2:2022 Cleanouts

View more information
US$83.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.