ASTM D 4193 : 2008 : R2013 : EDT 1
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Test Method for Thiocyanate in Water
Hardcopy , PDF
08-25-2020
English
06-01-2013
CONTAINED IN VOL. 11.02, 2017 Specifies the quantitative colorimetric laboratory measurement of dissolved thiocyanate in water, waste water, and saline water in the range from 0.1 to 2.0 mg/L.
1.1This test method covers the quantitative colorimetric laboratory measurement of dissolved thiocyanate in water, waste water, and saline water in the range from 0.1 to 2.0 mg/L. For higher concentrations, use an aliquot from the diluted sample.
1.1.1Validation—This test method was validated over the range of 0.07 to 1.42 mg/L. This test method was validated at nine laboratories at four levels. This test method may be valid for reporting results down to lower levels as validated in individual user laboratories.
1.1.2Application—This test method has been validated in reagent water, Type II, in multiple laboratories and 7 natural waters, 1 laboratory effluent, 1 steel mill effluent, and 2 dechlorinated and treated sanitary effluents in single laboratories. It is the user's responsibility to assure the validity of the test method on any untested matrices.
1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 9.
| Committee |
D 19
|
| DocumentType |
Test Method
|
| Pages |
6
|
| ProductNote |
Reconfirmed EDT 1
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM D 3694 : 1996 : R2017 | Standard Practices for Preparation of Sample Containers and for Preservation of Organic Constituents |
| ASTM D 7365 : 2007 | Standard Practice for Sampling, Preservation and Mitigating Interferences in Water Samples for Analysis of Cyanide |
| ASTM D 4841 : 1988 : R2008 | Standard Practice for Estimation of Holding Time for Water Samples Containing Organic and Inorganic Constituents |
| ASTM D 3370 : 1995 : REV A : R2003 : EDT 1 | Standard Practices for Sampling Water from Closed Conduits |
| ASTM D 1129 : 2013 : REDLINE | Standard Terminology Relating to Water |
| ASTM D 1129 : 2003 | Standard Terminology Relating to Water |
| ASTM D 2777 : 2013 : REDLINE | Standard Practice for Determination of Precision and Bias of Applicable Test Methods of Committee D19 on Water |
| ASTM D 7365 : 2009 | Standard Practice for Sampling, Preservation and Mitigating Interferences in Water Samples for Analysis of Cyanide |
| ASTM D 5788 : 1995 : R2001 | Standard Guide for Spiking Organics into Aqueous Samples |
| ASTM D 5788 : 1995 : R2017 | Standard Guide for Spiking Organics into Aqueous Samples |
| ASTM D 4841 : 1988 : R2018 | Standard Practice for Estimation of Holding Time for Water Samples Containing Organic and Inorganic Constituents |
| ASTM D 1129 : 2013 | Standard Terminology Relating to Water |
| ASTM D 7237 : 2018 | Standard Test Method for Free Cyanide and Aquatic Free Cyanide with Flow Injection Analysis (FIA) Utilizing Gas Diffusion Separation and Amperometric Detection |
| ASTM D 2036 : 1991 | Standard Test Methods for Cyanides in Water |
| ASTM D 5847 : 1999 : REV A : EDT 1 | Standard Practice for Writing Quality Control Specifications for Standard Test Methods for Water Analysis |
| ASTM D 2777 : 2012 | Standard Practice for Determination of Precision and Bias of Applicable Test Methods of Committee D19 on Water |
| ASTM D 1193 : 1977 : R1983 : EDT 1 | Standard Specification for Reagent Water |
| ASTM D 4841 : 1988 : R1998 | Standard Practice for Estimation of Holding Time for Water Samples Containing Organic and Inorganic Constituents |
| ASTM D 5847 : 2002 : R2007 | Standard Practice for Writing Quality Control Specifications for Standard Test Methods for Water Analysis |
| ASTM D 5788 : 1995 | Standard Guide for Spiking Organics into Aqueous Samples |
| ASTM D 1129 : 2006 | Standard Terminology Relating to Water |
| ASTM D 2777 : 2003 | Standard Practice for Determination of Precision and Bias of Applicable Methods of Committee D-19 on Water |
| ASTM D 4841 : 1988 : R2003 | Standard Practice for Estimation of Holding Time for Water Samples Containing Organic and Inorganic Constituents |
| ASTM D 3370 : 2010 | Standard Practices for Sampling Water from Closed Conduits |
| ASTM D 2777 : 2013 | Standard Practice for Determination of Precision and Bias of Applicable Test Methods of Committee D19 on Water |
| ASTM E 275 : 2008 | Describing and Measuring Performance of Ultraviolet and Visible Spectrophotometers |
| ASTM D 7365 : 2009 : REV A | Standard Practice for Sampling, Preservation and Mitigating Interferences in Water Samples for Analysis of Cyanide |
| ASTM D 4841 : 1988 : R2013 | Standard Practice for Estimation of Holding Time for Water Samples Containing Organic and Inorganic Constituents |
| ASTM D 5847 : 2002 : R2012 | Standard Practice for Writing Quality Control Specifications for Standard Test Methods for Water Analysis |
| ASTM D 2777 : 1998 | Standard Practice for Determination of Precision and Bias of Applicable Methods of Committee D-19 on Water |
| ASTM D 2036 : 2009 : R2015 | Standard Test Methods for Cyanides in Water |
| ASTM D 3370 : 2008 | Standard Practices for Sampling Water from Closed Conduits |
| ASTM D 1129 : 1999 : REV A | Standard Terminology Relating to Water |
| ASTM D 2036 : 1998 | Standard Test Methods for Cyanides in Water |
| ASTM D 3856 : 2011 | Standard Guide for Management Systems in Laboratories Engaged in Analysis of Water |
| ASTM D 1129 : 2006 : REV A | Standard Terminology Relating to Water |
| ASTM D 1193 : 2006 : R2011 | Standard Specification for Reagent Water |
| ASTM D 1129 : 2003 : REV A | Standard Terminology Relating to Water |
| ASTM D 1129 : 2002 | Standard Terminology Relating to Water |
| ASTM D 2036 : 2009 | Standard Test Methods for Cyanides in Water |
| ASTM D 5788 : 1995 : R2005 | Standard Guide for Spiking Organics into Aqueous Samples |
| ASTM D 5788 : 1995 : R2011 | Standard Guide for Spiking Organics into Aqueous Samples |
| ASTM D 7237 : 2010 | Standard Test Method for Free Cyanide with Flow Injection Analysis (FIA) Utilizing Gas Diffusion Separation and Amperometric Detection |
| ASTM D 1193 : 1991 | Standard Specification for Reagent Water |
| ASTM D 7237 : 2015 : REV A | Standard Test Method for Free Cyanide and Aquatic Free Cyanide with Flow Injection Analysis (FIA) Utilizing Gas Diffusion Separation and Amperometric Detection |
| ASTM D 7237 : 2006 | Standard Test Method for Aquatic Free Cyanide with Flow Injection Analysis (FIA) Utilizing Gas Diffusion Separation and Amperometric Detection |
| ASTM D 3856 : 1995 : R2006 | Standard Guide for Good Laboratory Practices in Laboratories Engaged in Sampling and Analysis of Water |
| ASTM D 1129 : 2004 | Standard Terminology Relating to Water |
| ASTM D 2777 : 2008 | Standard Practice for Determination of Precision and Bias of Applicable Test Methods of Committee D19 on Water |
| ASTM D 3856 : 2011 : R2015 | Standard Guide for Management Systems in Laboratories Engaged in Analysis of Water (Withdrawn 2024) |
| ASTM D 1192 : 1998 | Standard Guide for Equipment for Sampling Water and Steam in Closed Conduits (Withdrawn 2003) |
| ASTM D 2777 : 2006 | Standard Practice for Determination of Precision and Bias of Applicable Test Methods of Committee D19 on Water |
| ASTM D 3856 : 1995 : R2000 | Standard Guide for Good Laboratory Practices in Laboratories Engaged in Sampling and Analysis of Water |
| ASTM D 3370 : 2018 | Standard Practices for Sampling Water from Flowing Process Streams |
| ASTM D 1129 : 2002 : REV A | Standard Terminology Relating to Water |
| ASTM D 5847 : 2002 | Standard Practice for Writing Quality Control Specifications for Standard Test Methods for Water Analysis |
| ASTM D 3370 : 1976 | Standard Practices for Sampling Water |
| ASTM D 7365 : 2009 : REV A : R2015 | Standard Practice for Sampling, Preservation and Mitigating Interferences in Water Samples for Analysis of Cyanide |
| ASTM D 1193 : 1970 | Standard Specification For Reagent Water |
| ASTM D 4841 : 1988 : R2013 : EDT 1 | Standard Practice for Estimation of Holding Time for Water Samples Containing Organic and Inorganic Constituents |
| ASTM D 1193 : 2006 | Standard Specification for Reagent Water |
| ASTM D 3370 : 1995 : REV A : R1999 : EDT 1 | Standard Practices for Sampling Water from Closed Conduits |
| ASTM D 1193 : 1999 | Standard Specification for Reagent Water |
| ASTM D 1129 : 2010 | Standard Terminology Relating to Water |
| ASTM D 4210 : 1989 : R1996 : EDT 1 | Standard Practice for Intralaboratory Quality Control Procedures and a Discussion on Reporting Low-Level Data (Withdrawn 2002) |
| ASTM D 3370 : 2007 | Standard Practices for Sampling Water from Closed Conduits |
| ASTM D 2036 : 2006 | Standard Test Methods for Cyanides in Water |
| ASTM D 1129 : 2006 : REV A : EDT 1 | Standard Terminology Relating to Water |
| ASTM D 1129 : 2001 | Standard Terminology Relating to Water |
| ASTM D 7237 : 2015 | Standard Test Method for Free Cyanide and Aquatic Free Cyanide with Flow Injection Analysis (FIA) Utilizing Gas Diffusion Separation and Amperometric Detection |
| ASTM D 1129 : 2004 : EDT 1 | Standard Terminology Relating to Water |
| ASTM D 1193 : 2006 : R2018 | Standard Specification for Reagent Water |
| ASTM D 2777 : 2008 : EDT 1 | Standard Practice for Determination of Precision and Bias of Applicable Test Methods of Committee D19 on Water |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.