Standard Test Method for Indicating Moisture in Concrete by the Plastic Sheet Method

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-17-2024

Publisher

American Society for Testing and Materials

CONTAINED IN VOL. 06.02, 2017 Describes the presence of capillary moisture in concrete.

1.1This test method is used to indicate the presence of capillary moisture in concrete.

1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific caution statements, see Section 4.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee	D 01
DocumentType	Test Method
Pages	2
PublisherName	American Society for Testing and Materials
Status	Current
SupersededBy	ASTM D 4263 : 1983 : R2012 ASTM D 4263 : 1983 : R1999 ASTM D 4263 : 1983 : R2005 ASTM D 3089 : 1997 : R2008
Supersedes	ASTM D 4263 : 1983 : R2012

NACE 6 : 2003	SURFACE PREPARATION OF CONCRETE
ASTM D 5107 : 2003 : R2013	Standard Practice for Preparatory Surface Cleaning of Architectural Sandstone
AASHTO PP 73 : 2013 : R2015	PRACTICE FOR QUALITY ASSURANCE, JOB SITE QUALITY CONTROL, AND REAPPLICATION OF PROTECTIVE SEALERS FOR PORTLAND CEMENT CONCRETE
ACI 360R : 2010	GUIDE TO DESIGN OF SLABS-ON-GROUND
ASTM D 5107 : 2003	Standard Practice for Preparatory Surface Cleaning of Architectural Sandstone
ACI 503.6R : 1997	GUIDE FOR THE APPLICATION OF EPOXY AND LATEX ADHESIVES FOR BONDING FRESHLY MIXED AND HARDENED CONCRETES
NACE RP 02 98 : 0	SHEET RUBBER LININGS FOR ABRASION AND CORROSION SERVICE
NACE RP 08 92 : 2001	COATINGS AND LININGS OVER CONCRETE FOR CHEMICAL IMMERSION AND CONTAINMENT SERVICE
ASTM D 5295/D5295M : 2018 : REDLINE	Standard Guide for Preparation of Concrete Surfaces for Adhered (Bonded) Membrane Waterproofing Systems
ASTM D 3089 : 1997 : R2008	Standard Practice for Determining the A-D Dimension of Aerosol Valve Dip Tubes
ASTM D 4258 : 2005 : R2017	Standard Practice for Surface Cleaning Concrete for Coating
ASTM D 3805/D3805M : 2016 : REDLINE	Standard Guide for Application of Aluminum-Pigmented Asphalt Roof Coatings
ASTM C 1471 : 2005	Standard Guide for the Use of High Solids Content Cold Liquid-Applied Elastomeric Waterproofing Membrane on Vertical Surfaces
NACE 02203 : 0	DESIGN, INSTALLATION, AND MAINTENANCE OF PROTECTIVE POLYMER FLOORING SYSTEMS FOR CONCRETE
NACE SP 02 98 : 2007	SHEET RUBBER LININGS FOR ABRASION AND CORROSION SERVICE
NACE RP 02 88 : 2004	INSPECTION OF LININGS ON STEEL AND CONCRETE
CSA S413 : 2014	PARKING STRUCTURES
ASTM D 3805 : 1997	Standard Guide for Application of Aluminum-Pigmented Asphalt Roof Coatings
ASTM D 5295 : 2000 : R2006	Standard Guide for Preparation of Concrete Surfaces for Adhered (Bonded) Membrane Waterproofing Systems
NACE SP 08 92 : 2007	COATINGS AND LININGS OVER CONCRETE FOR CHEMICAL IMMERSION AND CONTAINMENT SERVICE
ASTM D 5295 : 2000	Standard Guide for Preparation of Concrete Surfaces for Adhered (Bonded) Membrane Waterproofing Systems
ACI 503.3M : 2010	SPECIFICATION FOR PRODUCING A SKID-RESISTANT SURFACE ON CONCRETE BY THE USE OF EPOXY AND AGGREGATE - METRIC
ASTM D 4258 : 2005 : R2012	Standard Practice for Surface Cleaning Concrete for Coating
ASTM C 1848 : 2017	Standard Practice for Installation of High-Pressure Spray Polyurethane Foam Insulation for the Building Enclosure
UFC 3-110-03 : Change 2	UNIFIED FACILITIES CRITERIA - ROOFING
ASTM D 4261 : 2005 : R2018	Standard Practice for Surface Cleaning Concrete Masonry Units for Coating
NACE SP 02 88:2011	INSPECTION OF LINING APPLICATION IN STEEL AND CONCRETE EQUIPMENT
SSPC-PA 14 : 2012	APPLICATION OF THICK FILM POLYUREA AND POLYURETHANE COATINGS TO CONCRETE AND STEEL USING PLURAL-COMPONENT EQUIPMENT
DKD-R 3-5 :2018	PRACTICE FOR QUALITY ASSURANCE, JOB SITE QUALITY CONTROL, AND REAPPLICATION OF PROTECTIVE SEALERS FOR PORTLAND CEMENT CONCRETE
SSPC-GUIDE 20 : 2014	GUIDE FOR APPLYING THICK FILM COATINGS AND SURFACINGS OVER CONCRETE FLOORS
ACI 548.10 : 2010	SPECIFICATION FOR TYPE MMS (METHYL METHACRYLATE SLURRY) POLYMER OVERLAYS FOR BRIDGE AND PARKING GARAGE DECKS
ACI 302.2R : 2006	GUIDE FOR CONCRETE SLABS THAT RECEIVE MOISTURE-SENSITIVE FLOORING MATERIALS
ACI 524R : 2016	GUIDE TO PORTLAND CEMENT-BASED PLASTER
ACI SPEC-548.10 : 2010	SPECIFICATION FOR TYPE MMS (METHYL METHACRYLATE SLURRY) POLYMER OVERLAYS FOR BRIDGE AND PARKING GARAGE DECKS
ACI 548.8 : 2007	SPECIFICATION FOR TYPE EM (EPOXY MULTI-LAYER) POLYMER OVERLAY FOR BRIDGE AND PARKING GARAGE DECKS
ACI 503.3 : 2010	SPECIFICATION FOR PRODUCING A SKID-RESISTANT SURFACE ON CONCRETE BY THE USE OF EPOXY AND AGGREGATE
ACI 548.8M : 2007	SPECIFICATION FOR TYPE EM (EPOXY MULTI-LAYER) POLYMER OVERLAY FOR BRIDGE AND PARKING GARAGE DECKS
ASTM D 4261 : 2005 : R2012	Standard Practice for Surface Cleaning Concrete Masonry Units for Coating
ASTM D 4260 : 2005 : R2017	Standard Practice for Liquid and Gelled Acid Etching of Concrete
ASTM D 4261 : 2005	Standard Practice for Surface Cleaning Concrete Masonry Units for Coating
ASTM C 811 : 1998 : R2008	Standard Practice for Surface Preparation of Concrete for Application of Chemical-Resistant Resin Monolithic Surfacings (Withdrawn 2012)
ASTM C 811 : 1998 : R2003	Standard Practice for Surface Preparation of Concrete for Application of Chemical-Resistant Resin Monolithic Surfacings
CSA A23.1 A23.2 : 2014	CONCRETE MATERIALS AND METHODS OF CONCRETE CONSTRUCTION/TEST METHODS AND STANDARD PRACTICES FOR CONCRETE
ASTM D 4260 : 2005	Standard Practice for Liquid and Gelled Acid Etching of Concrete
ACI 351.1R : 2012	REPORT ON GROUTING BETWEEN FOUNDATIONS AND BASES FOR SUPPORT OF EQUIPMENT & MACHINERY
ACI 548.9 : 2008	SPECIFICATION FOR TYPE ES (EPOXY SLURRY) POLYMER OVERLAYS FOR BRIDGE AND PARKING GARAGE DECKS
ASTM D 6237 : 2009	Standard Guide for Painting Inspectors (Concrete and Masonry Substrates)
ASTM D 6237 : 2009 : R2015	Standard Guide for Painting Inspectors (Concrete and Masonry Substrates)
ASTM D 5295/D5295M : 2018	Standard Guide for Preparation of Concrete Surfaces for Adhered (Bonded) Membrane Waterproofing Systems
ASTM D 3805/D3805M : 2016	Standard Guide for Application of Aluminum-Pigmented Asphalt Roof Coatings
ASTM D 5498 : 2012 : REV A : R2018	Standard Guide for Developing a Training Program for Personnel Performing Coating and Lining Work Inspection for Nuclear Facilities
ASTM C 1848 : 2017 : REV A	Standard Practice for Installation of High-Pressure Spray Polyurethane Foam Insulation for the Building Enclosure
ASTM F 710 : 2019	Standard Practice for Preparing Concrete Floors to Receive Resilient Flooring
ASTM F 2419 : 2011 : R2017	Standard Practice for Installation of Thick Poured Gypsum Concrete Underlayments and Preparation of the Surface to Receive Resilient Flooring
ASTM F 2419 : 2011	Standard Practice for Installation of Thick Poured Gypsum Concrete Underlayments and Preparation of the Surface to Receive Resilient Flooring
ACI 548.9M : 2008	SPECIFICATION FOR TYPE ES (EPOXY SLURRY) POLYMER OVERLAY FOR BRIDGE AND PARKING GARAGE DECKS
ASTM C 1471/C1471M : 2005 : R2014 : EDT 1	Standard Guide for the Use of High Solids Content Cold Liquid-Applied Elastomeric Waterproofing Membrane on Vertical Surfaces
ASTM D 5107 : 2003 : R2007	Standard Practice for Preparatory Surface Cleaning of Architectural Sandstone
NACE RP 05 91 : 91(R1996)	COATINGS FOR CONCRETE SURFACES IN NON-IMMERSION AND ATMOSPHERIC SERVICE
ACI 548.11R : 2012	GUIDE FOR THE APPLICATIONS OF EPOXY AND LATEX ADHESIVES FOR BONDING FRESHLY MIXED AND HARDENED CONCRETES
NACE 6G197 : 0	DESIGN, INSTALLATION, AND MAINTENANCE OF COATING SYSTEMS FOR CONCRETE USED IN SECONDARY CONTAINMENT
ASTM D 4260 : 2005 : R2012	Standard Practice for Liquid and Gelled Acid Etching of Concrete
ASTM C 811 : 1998	Standard Practice for Surface Preparation of Concrete for Application of Chemical-Resistant Resin Monolithic Surfacings
ASTM D 4258 : 2005	Standard Practice for Surface Cleaning Concrete for Coating
ACI SPEC-548.10:2022	Type Methyl Methacrylate Slurry (MMS) Polymer Overlays for Bridge and Parking Garage Deck— Specification
ASTM C 1848 : 2017 : REV A : R2023	Standard Practice for Installation of High-Pressure Spray Polyurethane Foam Insulation for the Building Enclosure
ASTM D 4258 : 2023	Standard Practice for Surface Cleaning Concrete for Coating
ASTM F 710 : 2022	Standard Practice for Preparing Concrete Floors to Receive Resilient Flooring
ASTM D 4260 : 2023	Standard Practice for Liquid and Gelled Acid Etching of Concrete
ASTM D 5107 : 2003 : R2022	Standard Practice for Preparatory Surface Cleaning of Architectural Sandstone
ASTM F 2419 : 2011 : R2021	Standard Practice for Installation of Thick Poured Gypsum Concrete Underlayments and Preparation of the Surface to Receive Resilient Flooring
ASTM C 1471/C1471M : 2022	Standard Guide for the Use of High Solids Content Cold Liquid-Applied Elastomeric Waterproofing Membrane on Vertical Surfaces
ASTM D 3805/D3805M : 2016 : R2023	Standard Guide for Application of Aluminum-Pigmented Asphalt Roof Coatings
ASTM D 6237 : 2019	Standard Guide for Painting Inspectors (Concrete and Masonry Substrates)