• There are no items in your cart

ASTM D 5205 : 2016 : REDLINE

Current
Current

The latest, up-to-date edition.

Standard Classification System and Basis for Specification for Polyetherimide (PEI) Materials
Available format(s)

PDF

Language(s)

English

Published date

09-01-2016

CONTAINED IN VOL. 08.03, 2016 Defines unfilled, filled, and reinforced polyetherimide materials suitable for injection molding and extrusion.

1.1This classification system covers unfilled, filled, and reinforced polyetherimide materials suitable for injection molding and extrusion.

1.2This classification system is not intended for the selection of materials, but only as a means to call out plastic materials to be used for the manufacture of parts. The selection of these materials is to be made by personnel with expertise in the plastics field where the environment, inherent properties of the materials, performance of the parts, part design, manufacturing process, and economics are considered.

1.3The properties included in this classification system are those required to identify the compositions covered. Other requirements necessary to identify particular characteristics important to specialized applications are to be specified by using suffixes as given in Section 5.

1.4Polyetherimide materials, being thermoplastic, are reprocessable and recyclable. This classification system allows for the use of those polyetherimide materials, provided that all specific requirements of this classification system are met.

1.5The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.6The following precautionary caveat pertains only to the test methods portion, Section 12, of this classification system: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given at the end of 5.4.

Note 1:There is no known ISO equivalent to this standard.

Committee
D 20
DocumentType
Redline
Pages
10
PublisherName
American Society for Testing and Materials
Status
Current

MIL-DTL-12883 Revision F:2003 Sockets and Accessories for Plug-in Electronic Components, General Specification for
16/30338304 DC : 0 BS ISO/ASTM 52903-1 - ADDITIVE MANUFACTURING - STANDARD SPECIFICATION FOR MATERIAL EXTRUSION BASED ADDITIVE MANUFACTURING OF PLASTIC MATERIALS - PART 1: FEEDSTOCK MATERIALS
ASTM D 7293 : 2012 : REDLINE Standard Specification for Extruded and Compression-Molded Shapes Made from Polyetherimide (PEI)
ASTM D 4000 : 2016 : REDLINE Standard Classification System for Specifying Plastic Materials
MIL-DTL-32546-3 Base Document:2016 Connectors, Electrical, Circular, Receptacle, Threaded, Jam Nut Mounting, High-Speed Data
MIL PRF 12883 : E SOCKETS AND ACCESSORIES FOR PLUG-IN ELECTRONIC COMPONENTS, GENERAL SPECIFICATION FOR
MIL-DTL-32546-1 Base Document:2016 Connectors, Electrical, Circular, Receptacle, High-Speed Data, Threaded, Square Flange

ASTM D 618 : 2013 : REDLINE Standard Practice for Conditioning Plastics for Testing
ASTM D 7209 : 2006 Standard Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products (Withdrawn 2015)
ASTM D 1238 : 2013 : REDLINE Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
ASTM D 3641 : 2015 : REDLINE Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
ASTM D 792 : 2013 : REDLINE Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
ASTM D 790 : 2017 : REDLINE Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
ASTM D 5630 : 2013 : REDLINE Standard Test Method for Ash Content in Plastics (Withdrawn 2022)
ASTM E 662 : 2017-02 TEST METHOD FOR SPECIFIC OPTICAL DENSITY OF SMOKE GENERATED BY SOLID MATERIALS
ASTM D 648 : 2016 Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position
ASTM D 257 : 2014 : REDLINE Standard Test Methods for DC Resistance or Conductance of Insulating Materials
MIL-M-24519 Revision E:1992 MOLDING PLASTICS, POLYESTER AND POLYARYLETHER THERMOPLASTIC
ASTM D 638 : 2014 : REDLINE Standard Test Method for Tensile Properties of Plastics
MIL-P-46184 Base Document:1982 PLASTIC MOLDING & EXTRUSION MATERIAL, POLYETHERIMIDE (PEI)
ASTM D 3892 : 2015 : REDLINE PRACTICE FOR PACKAGING/PACKING OF PLASTICS
ASTM D 4000 : 2016 : REDLINE Standard Classification System for Specifying Plastic Materials

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.