• There are no items in your cart

ASTM D 5967 : 2012

NA
NA

Status of Standard is Unknown

Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

04-15-2012

1.1 This test method covers an engine test procedure for evaluating diesel engine oils for performance characteristics, including viscosity increase and soot concentrations (loading). This test method is commonly referred to as the Mack T-8.

1.2 This test method also provides the procedure for running an extended length T-8 test, which is commonly referred to as the T-8E and an abbreviated length test, which is commonly referred to as T-8A. The procedures for the T-8E and the T-8A are identical to the T-8 with the exception of the items specifically listed in Annex A8 and Annex A9 respectively. Additionally, the procedure modifications listed in Annex A8 and Annex A9 refer to the corresponding section of the T-8 procedure.

1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.3.1 ExceptionsWhere there is no direct SI equivalent such as the units for screw threads, National Pipe Threads/diameters, tubing size, sole source equipment suppliers, and oil consumption in grams per kilowatthour.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Annex A6 for specific safety precautions.

1.5 A Table of Contents follows:

Scope1
Referenced Documents2
Terminology3
Summary of Test Method4
Significance and Use5
Apparatus6
General Description6.1
The Test Engine6.2
Mack Test Engine6.2.1
Engine Cooling System6.2.2
Engine Oil System6.2.3
Auxiliary Oil System6.2.4
Crankcase Aspiration6.2.5
Blowby Meter6.2.6
Air Supply and Filtration6.2.7
Fuel Supply6.2.8
Intake Manifold Temperature Control6.2.9
Engine Fluids7
Test Oil7.1
Test Fuel7.2
Engine Coolant7.3
Cleaning Materials7.4
Preparation of Apparatus at Rebuild8
Cleaning of Parts8.1
Valves, Seats, Guides, and Springs8.2
Cylinder Liner, Piston, and Piston Ring Assembly8.3
Injectors and Injection Pump8.4
Assembly Instructions8.5
Measurements8.6
Laboratory and Engine Test Stand Calibration/Non-Reference
Requirements
9
Calibration Frequency9.1
Calibration Reference Oils9.2
Test Numbering9.3
New Laboratories and New Test Stands9.4
Calibrated Laboratories and Test Stands9.5
Calibration Test Acceptance9.6
Failing Calibration Tests9.7
Non-Reference Oil Test Requirements9.8
Procedure10
Pretest Procedure10.1
Engine Start-Up10.2
Engine Shutdown10.3
Test Cycle10.4
Oil Addition/Drain10.5
Oil Samples10.6
Oil Consumption Calculations10.7
Fuel Samples10.8
Periodic Measurements10.9
Blowby10.10
Centrifugal Oil Filter Mass Gain10.11
Oil Filter ΔP Calculation10.12
Post Test10.13
Inspection of Fuel and Oil During Test11
Oil Inspection11.1
Fuel Inspections11.2
Oil Consumption11.3
Report 12
Reporting Test Results12.1
Deviations from Test Operational Limits12.2
Electronic Transmission of Test Results12.3
Plots of Operational Data12.4
Precision and Bias13
Precision13.1
Bias13.2
Keywords14
Annexes
Report FormsAnnex A1
Sensor LocationsAnnex A2
Kinematic Viscosity At 100°C For Test Method D5967 Samples Annex A3
Enhanced Thermal Gravimetric Analysis (TGA) ProcedureAnnex A4
Procurement of Test MaterialsAnnex A5
Safety PrecautionsAnnex A6
Data DictionaryAnnex A7
T-8E Extended Length Test RequirementsAnnex A8
T-8A Abbreviated Length Test RequirementsAnnex A9

Committee
D 02
DocumentType
Test Method
Pages
21
PublisherName
American Society for Testing and Materials
Status
NA
SupersededBy
Supersedes

ASTM D 7483 : 2013 : REV A : R2017 Standard Test Method for Determination of Dynamic Viscosity and Derived Kinematic Viscosity of Liquids by Oscillating Piston Viscometer
ASTM D 8048 : 2019 Standard Test Method for Evaluation of Diesel Engine Oils in T-13 Diesel Engine
ASTM D 6987/D6987M : 2013 : REV A Standard Test Method for Evaluation of Diesel Engine Oils in T-10 Exhaust Gas Recirculation Diesel Engine (Withdrawn 2022)
ASTM D 7686 : 2011 Standard Test Method for Field-Based Condition Monitoring of Soot in In-Service Lubricants Using a Fixed-Filter Infrared (IR) Instrument
ASTM D 7422 : 2017 : REV A Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine
ASTM D 7596 : 2014 Standard Test Method for Automatic Particle Counting and Particle Shape Classification of Oils Using a Direct Imaging Integrated Tester
ASTM D 6923 : 2018 Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1R Test Procedure
ASTM D 7583 : 2016 Standard Test Method for John Deere Coolant Cavitation Test
ASTM D 8074 : 2018 Standard Test Method for Evaluation of Diesel Engine Oils in DD13 Diesel Engine
ASTM D 7156 : 2017 Standard Test Method for Evaluation of Diesel Engine Oils in the T-11 Exhaust Gas Recirculation Diesel Engine
ASTM D 6895 : 2017 Standard Test Method for Rotational Viscosity of Heavy Duty Diesel Drain Oils at 100 °C
ASTM D 7844 : 2018 Standard Test Method for Condition Monitoring of Soot in In-Service Lubricants by Trend Analysis using Fourier Transform Infrared (FT-IR) Spectrometry
ASTM D 7317 : 2007 : R2019 Standard Test Method for Coagulated Pentane Insolubles in Used Lubricating Oils by Paper Filtration (LMOA Method)
SAE J304:2023 Engine Oil Tests

View more information
US$108.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.