Standard Specification for Extruded and Monomer Cast Shapes Made from Nylon (PA)

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

08-01-2018

Publisher

American Society for Testing and Materials

This specification covers requirements and test methods for the material, dimensions, and workmanship, and the properties of extruded and cast sheet, plate, rod and tubular bar, excluding pipe and fittings, manufactured from nylon or monomers.

1.1This specification covers requirements and test methods for the material, dimensions, and workmanship, and the properties of extruded and cast sheet, plate, rod and tubular bar, excluding pipe and fittings, manufactured from nylon or monomers.

1.2The properties included in this specification are those required for the compositions covered. Requirements necessary to identify particular characteristics important to specialized applications are described by using the classification system given in Section 4.

1.3This specification allows for the use of recycled plastics (as defined in Guide D7209).

1.4The values stated in English units are regarded as standard. The values in parentheses are for information only.

1.5The following precautionary caveat pertains only to the test method portions of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

Note 1:There is no known ISO equivalent to this standard.

Note 2:This specification is intended to replace Federal Standard LP-410A and PS 50.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee	D 20
DocumentType	Standard
Pages	7
ProductNote	This standard also refers to LP-410A
PublisherName	American Society for Testing and Materials
Status	Current
Supersedes	ASTM D 5989 : 2014 ASTM D 5989 : 2014 : REV A

ASTM D 256 : 2010 : R2018	Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
ASTM D 6779 : 2002	Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 883 : 2023	Standard Terminology Relating to Plastics
ASTM D 6779 : 2005	Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2020	Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2007 : REV A	Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 3892 : 2015 : R2020	Standard Practice for Packaging/Packing of Plastics
ASTM D 6779 : 2003	Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 883 : 2024	Standard Terminology Relating to Plastics
ASTM D 3892 : 1993 : R2003	Standard Practice for Packaging/Packing of Plastics
ASTM D 256 : 2023 : EDT 1	Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
ASTM D 3892 : 2015	Standard Practice for Packaging/Packing of Plastics
ASTM D 6779 : 2011	Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 883 : 2022	Standard Terminology Relating to Plastics
ASTM D 883 : 2020 : REV B	Standard Terminology Relating to Plastics
ASTM D 7209 : 2006	Standard Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products (Withdrawn 2015)
ASTM D 6779 : 2008	Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 3892 : 1993 : R1998	Standard Practice for Packaging/Packing of Plastics
ASTM D 6779 : 2004	Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2012	Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2006	Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 256 : 2023	Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
ASTM D 638 : 2014	Standard Test Method for Tensile Properties of Plastics
ASTM D 6779 : 2004 : REV A	Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2023	Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2012 : REV A	Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2002 : REV A	Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 3892 : 1993 : R2009	Standard Practice for Packaging/Packing of Plastics
ASTM D 6779 : 2016	Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2007	Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2021	Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2010	Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2017	Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
ASTM D 6779 : 2008 : REV A	Standard Classification System for Polyamide Molding and Extrusion Materials (PA)
ASTM D 638 : 2022	Standard Test Method for Tensile Properties of Plastics
ASTM D 6779 : 2006 : EDT 1	Standard Classification System for Polyamide Molding and Extrusion Materials (PA)