• There are no items in your cart

ASTM D 6141 : 2018

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Guide for Screening Clay Portion and Index Flux of Geosynthetic Clay Liner (GCL) for Chemical Compatibility to Liquids
Available format(s)

Hardcopy , PDF

Superseded date

10-18-2022

Language(s)

English

Published date

06-08-2018

1.1This guide covers procedures and test methods that can be used in the evaluation of the ability of the clay portion of a geosynthetic clay liner to resist change due to exposure to liquids. These liquids may come from a site, or be generated in a laboratory from a site-specific soil.

1.2The scope of this guide is limited to short-term screening and is not intended to replace evaluation procedures that measure a performance property such as EPA 9100, Test Method D6766, or other suitable ASTM standards as they become available. This guide does not address potential adverse effects of wet-dry cycling.

1.3This guide applies to the clay component of a GCL. The swell index and fluid loss tests referenced in Section 8 may not be applicable to clay with polymer or other chemical treatment. However, the flux tests referenced in Section 9 are applicable to clay with polymer or other chemical treatment. It is acknowledged that some use the swell index or fluid loss procedure, or both, on clay with polymer or other chemical treatment. However, such use of the standard would be considered a modification of the procedure and must be reported as such. The synthetic carrier components are covered independently as described in Practice D5322.

1.4The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 35
DocumentType
Guide
Pages
3
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 4439 : 2020 Standard Terminology for Geosynthetics
ASTM D 5322 : 1998 Standard Practice for Immersion Procedures for Evaluating the Chemical Resistance of Geosynthetics to Liquids
ASTM D 5887/D5887M : 2020 Standard Test Method for Measurement of Index Flux Through Saturated Geosynthetic Clay Liner Specimens Using a Flexible Wall Permeameter
ASTM D 4439 : 2015 Standard Terminology for Geosynthetics
ASTM D 653 : 2007 Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 5890 : 2001 Standard Test Method for Swell Index of Clay Mineral Component of Geosynthetic Clay Liners
ASTM D 6766 : 2002 Standard Test Method for Evaluation of Hydraulic Properties of Geosynthetic Clay Liners Permeated with Potentially Incompatible Liquids
ASTM D 4439 : 2015 : REV A Standard Terminology for Geosynthetics
ASTM D 5890 : 2018 Standard Test Method for Swell Index of Clay Mineral Component of Geosynthetic Clay Liners
ASTM D 653 : 2020 : EDT 1 Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 4439 : 2017 Standard Terminology for Geosynthetics
ASTM D 653 : 2021 : REV A Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 5890 : 1995 Standard Test Method for Swell Index of Clay Mineral Component of Geosynthetic Clay Liners
ASTM D 6766 : 2020 Standard Test Method for Evaluation of Hydraulic Properties of Geosynthetic Clay Liners Permeated with Potentially Incompatible Aqueous Solutions
ASTM D 653 : 2021 Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 653 : 2021 : REV B Standard Terminology Relating to Soil, Rock, and Contained Fluids
ASTM D 6766 : 2018 Standard Test Method for Evaluation of Hydraulic Properties of Geosynthetic Clay Liners Permeated with Potentially Incompatible Aqueous Solutions
ASTM D 5322 : 2017 Standard Practice for Laboratory Immersion Procedures for Evaluating the Chemical Resistance of Geosynthetics to Liquids
ASTM D 4439 : 2000 Standard Terminology for Geosynthetics
ASTM D 5887/D5887M : 2022 Standard Test Method for Measurement of Index Flux Through Saturated Geosynthetic Clay Liner Specimens Using a Flexible Wall Permeameter
ASTM D 4439 : 2018 Standard Terminology for Geosynthetics

View more information
US$66.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.