• There are no items in your cart

ASTM D 6304:2016

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fischer Titration
Available format(s)

Hardcopy , PDF

Superseded date

01-30-2021

Language(s)

English

Published date

07-01-2016

CONTAINED IN VOL. 05.03, 2016 Defines the direct determination of water in the range of 10 to 25000 mg/kg entrained water in petroleum products and hydrocarbons using automated instrumentation.

1.1This test method covers the direct determination of water in the range of 10 mg/kg to 25 000 mg/kg entrained water in petroleum products and hydrocarbons using automated instrumentation. This test method also covers the indirect analysis of water thermally removed from samples and swept with dry inert gas into the Karl Fischer titration cell. Mercaptan, sulfide (S or H2S), sulfur, and other compounds are known to interfere with this test method (see Section 5).

1.2This test method is intended for use with commercially available coulometric Karl Fischer reagents and for the determination of water in additives, lube oils, base oils, automatic transmission fluids, hydrocarbon solvents, and other petroleum products. By proper choice of the sample size, this test method may be used for the determination of water from mg/kg to percent level concentrations.

1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
D 02
DocumentType
Test Method
Pages
6
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 1796 : 2011 : R2016 Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure)
ASTM D 4378 : 2013 Standard Practice for In-Service Monitoring of Mineral Turbine Oils for Steam, Gas, and Combined Cycle Turbines
ASTM D 7844 : 2018 Standard Test Method for Condition Monitoring of Soot in In-Service Lubricants by Trend Analysis using Fourier Transform Infrared (FT-IR) Spectrometry
ASTM D 6448 : 2016 Standard Specification for Industrial Burner Fuels from Used Lubricating Oils
ASTM D 7415 : 2018 Standard Test Method for Condition Monitoring of Sulfate By-Products in In-Service Petroleum and Hydrocarbon Based Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry
ASTM D 8185 : 2018 Standard Guide for In-Service Lubricant Viscosity Measurement
ASTM D 7566 : 2019 Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons
ASTM D 7754 : 2016 Standard Test Method for Determination of Trace Oxygenates in Automotive Spark-Ignition Engine Fuel by Multidimensional Gas Chromatography
ASTM D 6224 : 2016 Standard Practice for In-Service Monitoring of Lubricating Oil for Auxiliary Power Plant Equipment
ASTM D 8128 : 2017 Standard Guide for Monitoring Failure Mode Progression in Industrial Applications with Rolling Element Ball Type Bearings
ASTM D 8256 : 2019 Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation in the Sequence VH Spark-Ignition Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions
ASTM D 7590 : 2009 : R2014 Standard Guide for Measurement of Remaining Primary Antioxidant Content In In-Service Industrial Lubricating Oils by Linear Sweep Voltammetry
ASTM D 4304 : 2017 Standard Specification for Mineral and Synthetic Lubricating Oil Used in Steam or Gas Turbines
ASTM D 7973 : 2019 Standard Guide for Monitoring Failure Mode Progression in Plain Bearings
ASTM D 7124 : 2017 Standard Specification for Benzene for Use with Zeolite Based Catalysts
ASTM D 7185 : 2017 Standard Specification for Low Toluene Low Dioxane (LTLD) Benzene
ASTM E 2412 : 2010 : R2018 Standard Practice for Condition Monitoring of In-Service Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry
ASTM D 4868 : 2017 Standard Test Method for Estimation of Net and Gross Heat of Combustion of Hydrocarbon Burner and Diesel Fuels
ASTM D 7044 : 2015 Standard Specification for Biodegradable Fire Resistant Hydraulic Fluids (Withdrawn 2024)
ASTM D 4054 : 2019 Standard Practice for Evaluation of New Aviation Turbine Fuels and Fuel Additives
ASTM D 2699 : 2019 Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel
ASTM D 7796 : 2017 Standard Test Method for Analysis of Ethyl tert-Butyl Ether (ETBE) by Gas Chromatography
ASTM D 2700 : 2019 Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
ASTM D 7414 : 2018 Standard Test Method for Condition Monitoring of Oxidation in In-Service Petroleum and Hydrocarbon Based Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry
API MPM CH10.6:2022 Standard Test Method for Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure)
ASTM D 6439 : 2011 : R2017 Standard Guide for Cleaning, Flushing, and Purification of Steam, Gas, and Hydroelectric Turbine Lubrication Systems
ASTM D 6710 : 2017 Standard Guide for Evaluation of Hydrocarbon-Based Quench Oil
ASTM D 4293 : 2015 : EDT 1 Standard Specification for Phosphate Ester Based Fluids for Turbine Lubrication and Steam Turbine Electro-Hydraulic Control (EHC) Applications
ASTM D 7826 : 2019 Standard Guide for Evaluation of New Aviation Gasolines and New Aviation Gasoline Additives
ASTM D 2827 : 2019 Standard Specification for Styrene Monomer
ASTM D 7720 : 2011 : R2017 Standard Guide for Statistically Evaluating Measurand Alarm Limits when Using Oil Analysis to Monitor Equipment and Oil for Fitness and Contamination
ASTM E 1417/E1417M : 2016 Standard Practice for Liquid Penetrant Testing
ASTM D 6074 : 2015 Standard Guide for Characterizing Hydrocarbon Lubricant Base Oils
ASTM E 203 : 2016 Standard Test Method for Water Using Volumetric Karl Fischer Titration
ASTM D 7412 : 2018 Standard Test Method for Condition Monitoring of Phosphate Antiwear Additives in In-Service Petroleum and Hydrocarbon Based Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry
ASTM D 7155 : 2018 Standard Practice for Evaluating Compatibility of Mixtures of Turbine Lubricating Oils
ASTM D 7467 : 2019 Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20)
ASTM D 7596 : 2014 Standard Test Method for Automatic Particle Counting and Particle Shape Classification of Oils Using a Direct Imaging Integrated Tester

ASTM E 203 : 2016 : REDLINE Standard Test Method for Water Using Volumetric Karl Fischer Titration

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.