• There are no items in your cart

ASTM D 6353 : 2006 : R2017 : EDT 1

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Guide for Sampling Plan and Core Sampling for Prebaked Anodes Used in Aluminum Production
Available format(s)

Hardcopy , PDF

Superseded date

07-28-2023

Language(s)

English

Published date

02-20-2017

CONTAINED IN VOL. 05.03, 2017 Defines sampling for prebaked carbon anodes used in the production of aluminum, and details procedures for taking test samples from anode blocks.

1.1This guide covers sampling for prebaked carbon anodes used in the production of aluminum, and details procedures for taking test samples from anode blocks. It covers equipment and procedures for obtaining samples from anode blocks in a manner that does not destroy the block or prevent its subsequent use as originally intended. However, the user must determine the subsequent use of the sampled anode blocks. Preferred locations for taking samples from single units of anodes are covered in this guide.

1.1.1Information for sampling of shaped refractory products, in general, is given in ISO 5022. This standard details the statistical basis for sampling plans for acceptance testing of a consignment or lot. Anodes used in the production of aluminum have specific requirements for sampling and while the statistical basis for sampling given in ISO 5022 applies, further or modified requirements may also apply.

1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1:The following ASTM standards are noted as sources of useful information: Test Methods C559, C611, C651, C747, C1025, C1039, and E1225.

Committee
D 02
DocumentType
Guide
Pages
4
ProductNote
Reconfirmed EDT 1
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 6558 : 2000 : REV A : R2015 : EDT 1 Standard Test Method for Determination of TGA CO<inf>2</inf> Reactivity of Baked Carbon Anodes and Cathode Blocks
ASTM D 6558 : 2022 Standard Test Method for Determination of TGA CO<inf>2</inf> Reactivity of Baked Carbon Anodes and Cathode Blocks
ASTM D 6559 : 2022 Standard Test Method for Determination of Thermogravimetric (TGA) Air Reactivity of Baked Carbon Anodes and Cathode Blocks
ASTM D 6559 : 2000 : REV A : R2016 : EDT 1 Standard Test Method for Determination of Thermogravimetric (TGA) Air Reactivity of Baked Carbon Anodes and Cathode Blocks

ASTM C 1025 : 1991 : R2010 : EDT 1 Standard Test Method for Modulus of Rupture in Bending of Electrode Graphite
ASTM C 1025 : 1991 : R2005 Standard Test Method for Modulus of Rupture in Bending of Electrode Graphite
ASTM E 1225 : 2004 Standard Test Method for Thermal Conductivity of Solids by Means of the Guarded-Comparative-Longitudinal Heat Flow Technique
ASTM C 1039 : 1985 : R2015 Standard Test Methods for Apparent Porosity, Apparent Specific Gravity, and Bulk Density of Graphite Electrodes
ISO 5022:1979 Shaped refractory products Sampling and acceptance testing
ASTM C 611 : 2021 Standard Test Method for Electrical Resistivity of Manufactured Carbon and Graphite Articles at Room Temperature
ASTM E 1225 : 2009 Standard Test Method for Thermal Conductivity of Solids by Means of the Guarded-Comparative-Longitudinal Heat Flow Technique
ASTM C 611 : 1998 : R2016 Standard Test Method for Electrical Resistivity of Manufactured Carbon and Graphite Articles at Room Temperature
ASTM E 1225 : 1999 Standard Test Method for Thermal Conductivity of Solids by Means of the Guarded-Comparative-Longitudinal Heat Flow Technique
ASTM C 1025 : 2015 : R2020 Standard Test Method for Modulus of Rupture in Bending of Electrode Graphite
ASTM C 1039 : 1985 : R2010 : EDT 1 Standard Test Methods for Apparent Porosity, Apparent Specific Gravity, and Bulk Density of Graphite Electrodes
ASTM C 1025 : 2015 : REDLINE Standard Test Method for Modulus of Rupture in Bending of Electrode Graphite
ASTM C 1025 : 1991 : R2000 Standard Test Method for Modulus of Rupture in Bending of Electrode Graphite
ASTM C 747 : 2016 : REDLINE Standard Test Method for Moduli of Elasticity and Fundamental Frequencies of Carbon and Graphite Materials by Sonic Resonance
ASTM C 1039 : 1985 : R2000 Standard Test Methods for Apparent Porosity, Apparent Specific Gravity, and Bulk Density of Graphite Electrodes
ASTM C 1039 : 1985 : R2005 Standard Test Methods for Apparent Porosity, Apparent Specific Gravity, and Bulk Density of Graphite Electrodes
ASTM C 559 : 2016 : REDLINE Standard Test Method for Bulk Density by Physical Measurements of Manufactured Carbon and Graphite Articles
ASTM C 1025 : 2015 Standard Test Method for Modulus of Rupture in Bending of Electrode Graphite
ASTM E 1225 : 2013 Standard Test Method for Thermal Conductivity of Solids Using the Guarded-Comparative-Longitudinal Heat Flow Technique
ASTM C 651 : 2015 : REDLINE Standard Test Method for Flexural Strength of Manufactured Carbon and Graphite Articles Using Four-Point Loading at Room Temperature
ASTM E 1225 : 2013 : REDLINE Standard Test Method for Thermal Conductivity of Solids Using the Guarded-Comparative-Longitudinal Heat Flow Technique

View more information
US$66.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.