• There are no items in your cart

ASTM D 6574/D6574M : 2013 : EDT 1

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Determining the (In-Plane) Hydraulic Transmissivity of a Geosynthetic by Radial Flow
Available format(s)

Hardcopy , PDF

Superseded date

08-10-2021

Language(s)

English

Published date

03-10-2014

1.1This test method covers the procedure for determining the in-plane transmissivity of geosynthetics under varying normal compressive stresses using a radial flow apparatus. The test is intended to be an index test used primarily for geotextiles, although other products composed of geotextiles and geotextile-type materials may be suitable for testing with this test method.

1.2This test method is based on the assumption that the transmissivity of the geosynthetic is independent of orientation of the flow and is therefore limited to geosynthetics that have similar transmissivity in all directions and should not be used for materials with oriented flow behavior.

1.3This test method has been developed specifically for geosynthetics that have transmissivity values on the order of or less than 2 × 10−4 m2/s. Consider using Test Method D4716 for geosynthetics with transmissivity values higher than 2 × 10−4 m2/s.

1.4The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
D 35
DocumentType
Test Method
Pages
5
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 4716/D4716M : 2020 Standard Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant Head

ASTM D 5092 : 2004 : R2010 : EDT 1 Standard Practice for Design and Installation of Groundwater Monitoring Wells
ASTM D 4439 : 2020 Standard Terminology for Geosynthetics
ASTM D 4439 : 2015 Standard Terminology for Geosynthetics
ASTM D 5092 : 2002 Standard Practice for Design and Installation of Ground Water Monitoring Wells in Aquifers
ASTM D 4354 : 2012 Standard Practice for Sampling of Geosynthetics and Rolled Erosion Control Products(RECPs) for Testing
ASTM D 4716 : 2008 : R2013 Standard Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant Head
ASTM D 4354 : 2012 : R2020 Standard Practice for Sampling of Geosynthetics and Rolled Erosion Control Products (RECPs) for Testing
ASTM D 4716 : 2000 Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant Head
ASTM D 4439 : 2011 Standard Terminology for Geosynthetics
ASTM D 4716 : 2002 Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant Head
ASTM D 4439 : 2015 : REV A Standard Terminology for Geosynthetics
ASTM D 5092 : 2004 Standard Practice for Design and Installation of Ground Water Monitoring Wells in Aquifers
ASTM D 4439 : 2002 Standard Terminology for Geosynthetics
ASTM D 5092 : 2004 : EDT 1 Standard Practice for Design and Installation of Ground Water Monitoring Wells
ASTM D 4439 : 2017 Standard Terminology for Geosynthetics
ASTM D 4716 : 2008 Standard Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant Head
ASTM D 4716 : 2004 Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant Head
ASTM D 4716 : 2003 Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant Head
ASTM D 4716 : 2007 Standard Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant Head
ASTM D 5092 : 1990 : R1995 : EDT 1 Standard Practice for Design and Installation of Ground Water Monitoring Wells in Aquifers
ASTM D 4439 : 2001 Standard Terminology for Geosynthetics
ASTM D 4439 : 2014 Standard Terminology for Geosynthetics
ASTM D 4354 : 1999 : R2009 Standard Practice for Sampling of Geosynthetics for Testing
ASTM D 4354 : 1999 Standard Practice for Sampling of Geosynthetics for Testing
ASTM D 4439 : 2004 Standard Terminology for Geosynthetics
ASTM D 4439 : 2000 Standard Terminology for Geosynthetics
ASTM D 4716 : 2001 Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant Head
ASTM D 4354 : 1999 : R2004 Standard Practice for Sampling of Geosynthetics for Testing
ASTM D 4439 : 2018 Standard Terminology for Geosynthetics

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.