ASTM D 6677 : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Test Method for Evaluating Adhesion by Knife
Hardcopy , PDF
12-27-2022
English
07-02-2018
1.1This test method covers the procedure for assessing the adhesion of coating films to substrate by using a knife. 1.2This test method is used to establish whether the adhesion of a coating to a substrate or to another coating (in multi-coat systems) is at a generally adequate level. NOTE 1:The term “substrate” relates to the basic surface on which a coating adheres (may be steel, concrete, etc. or other coating). 1.3This method can be used in the laboratory and field .4The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee
1.1This test method covers the procedure for assessing the adhesion of coating films to substrate by using a knife.
1.2This test method is used to establish whether the adhesion of a coating to a substrate or to another coating (in multi-coat systems) is at a generally adequate level.
Note 1:The term “substrate” relates to the basic surface on which a coating adheres (may be steel, concrete, etc. or other coating).
1.3This method can be used in the laboratory and field.
1.4The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Committee |
D 01
|
| DocumentType |
Test Method
|
| Pages |
2
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM D 6944 : 2015 | Standard Practice for Determining the Resistance of Cured Coatings to Thermal Cycling |
| ASTM D 6237 : 2009 : R2015 | Standard Guide for Painting Inspectors (Concrete and Masonry Substrates) |
| ASTM D 5163 : 2016 | Standard Guide for Establishing a Program for Condition Assessment of Coating Service Level I Coating Systems in Nuclear Power Plants |
| ASTM D 5065 : 2017 | Standard Guide for Assessing the Condition of Aged Coatings on Steel Surfaces |
| ASTM D 6943 : 2015 | Standard Practice for Immersion Testing of Industrial Protective Coatings and Linings |
| ASTM D 5498 : 2012 : REV A : R2018 | Standard Guide for Developing a Training Program for Personnel Performing Coating and Lining Work Inspection for Nuclear Facilities |
| ASTM D 6577 : 2015 | Standard Guide for Testing Industrial Protective Coatings |
| ASTM D 7230 : 2006 : R2013 | Standard Guide for Evaluating Polymeric Lining Systems for Water Immersion in Coating Service Level III Safety-Related Applications on Metal Substrates |
| ASTM D 3276 : 2015 : EDT 1 | Standard Guide for Painting Inspectors (Metal Substrates) |
| ASTM D 6944 : 2015 : R2020 | Standard Practice for Determining the Resistance of Cured Coatings to Thermal Cycling |
| ASTM G 210 : 2013 : R2018 | Standard Practice for Operating the Severe Wastewater Analysis Testing Apparatus |
| ASTM D 6943 : 2015(R2019) | Standard Practice for Immersion Testing of Industrial Protective Coatings and Linings |
| ASTM D 5064 : 2016 : REV A : R2021 | Standard Practice for Conducting a Patch Test to Assess Coating Compatibility |
| ASTM D 5367 : 2016 : R2021 | Standard Practice for Evaluating Coatings Applied Over Surfaces Treated With Inhibitors Used to Prevent Flash Rusting of Steel When Water or Water/Abrasive Blasted |
| NACE AMPP SP2148:2022 | Maintenance Overcoating of Railcar Exteriors |
| ASTM D 3276 : 2021 | Standard Guide for Painting Inspectors (Metal Substrates) |
| ASTM A 1113/A1113M : 2020 : EDT 1 | Standard Specification for Corrugated Steel Structural Plate, Polymer-Coated, for Field-Bolted Pipe, Pipe-Arches, and Arches |
| ASTM D 6237 : 2019 | Standard Guide for Painting Inspectors (Concrete and Masonry Substrates) |
| ASTM D 7167 : 2012 : R2018 | Standard Guide for Establishing Procedures to Monitor the Performance of Safety-Related Coating Service Level III Lining Systems in an Operating Nuclear Power Plant |
| ASTM D 7230 : 2006 : R2021 | Standard Guide for Evaluating Polymeric Lining Systems for Water Immersion in Coating Service Level III Safety-Related Applications on Metal Substrates |
| ASTM D 5065 : 2017 : R2021 | Standard Guide for Assessing the Condition of Aged Coatings on Steel Surfaces |
| ASTM D 4619 : 2012 : R2018 | Standard Practice for Inspection of Linings in Operating Flue Gas Desulfurization Systems |
| ASTM D 6577 : 2015 : R2019 | Standard Guide for Testing Industrial Protective Coatings |
| ASTM D 5163 : 2016 : R2021 | Standard Guide for Establishing a Program for Condition Assessment of Coating Service Level I Coating Systems in Nuclear Power Plants |
| ASTM F 3182 : 2016 | Standard Practice for the Application of Spray-Applied Polymeric Liners Inside Pipelines for Potable Water |
| ASTM D 6132 : 2013 | Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Applied Organic Coatings Using an Ultrasonic Coating Thickness Gage |
| ASTM D 4138 : 2007 : REV A : R2022 | Standard Practices for Measurement of Dry Film Thickness of Protective Coating Systems by Destructive, Cross-Sectioning Means |
| ASTM D 3359 : 2009 : EDT 2 | Standard Test Methods for Measuring Adhesion by Tape Test |
| ASTM D 7234 : 2005 | Standard Test Method for Pull-Off Adhesion Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers |
| ASTM D 4138 : 1994 : R2001 : EDT 1 | Standard Test Methods for Measurement of Dry Film Thickness of Protective Coating Systems by Destructive Means |
| ASTM D 4541 : 2009 | Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers |
| ASTM D 2197 : 1998 : R2002 | Standard Test Method for Adhesion of Organic Coatings by Scrape Adhesion |
| ASTM D 6132 : 1997 | Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Applied Organic Coatings Over Concrete Using an Ultrasonic Gage |
| ASTM D 2197 : 2013 | Standard Test Method for Adhesion of Organic Coatings by Scrape Adhesion |
| ASTM D 7091 : 2022 | Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals |
| ASTM D 2197 : 1998 | Standard Test Method for Adhesion of Organic Coatings by Scrape Adhesion |
| ASTM D 4138 : 2007 : REV A : R2013 | Standard Practices for Measurement of Dry Film Thickness of Protective Coating Systems by Destructive, Cross-Sectioning Means |
| ASTM D 3359 : 1997 | Standard Test Methods for Measuring Adhesion by Tape Test |
| ASTM D 7234 : 2019 | Standard Test Method for Pull-Off Adhesion Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers |
| ASTM D 4541 : 2009 : EDT 1 | Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers |
| ASTM D 7091 : 2020 | Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals |
| ASTM D 4541 : 2002 | Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers |
| ASTM D 3359 : 2009 | Standard Test Methods for Measuring Adhesion by Tape Test |
| ASTM D 7234 : 2012 | Standard Test Method for Pull-Off Adhesion Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers |
| ASTM D 3359 : 2022 | Standard Test Methods for Rating Adhesion by Tape Test |
| ASTM D 4541 : 2017 | Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers |
| ASTM D 3359 : 2002 | Standard Test Methods for Measuring Adhesion by Tape Test |
| ASTM D 4541 : 2022 | Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers |
| ASTM D 3359 : 2009 : EDT 1 | Standard Test Methods for Measuring Adhesion by Tape Test |
| ASTM D 6132 : 2013 : R2017 | Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Applied Organic Coatings Using an Ultrasonic Coating Thickness Gage |
| ASTM D 4138 : 1994 : R1999 | Standard Test Methods for Measurement of Dry Film Thickness of Protective Coating Systems by Destructive Means |
| ASTM D 3359 : 2007 | Standard Test Methods for Measuring Adhesion by Tape Test |
| ASTM D 7091 : 2013 | Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals |
| ASTM D 2197 : 2010 | Standard Test Method for Adhesion of Organic Coatings by Scrape Adhesion |
| ASTM D 6132 : 2008 | Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Applied Organic Coatings Using an Ultrasonic Gage |
| ASTM D 2197 : 1986 : R1991 : EDT 1 | Standard Test Method for Adhesion of Organic Coatings by Scrape Adhesion |
| ASTM D 7091 : 2021 | Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals |
| ASTM D 7091 : 2012 | Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals |
| ASTM D 6132 : 2013 : R2022 | Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Applied Organic Coatings Using an Ultrasonic Coating Thickness Gage |
| ASTM D 2197 : 1998 : R2004 | Standard Test Method for Adhesion of Organic Coatings by Scrape Adhesion |
| ASTM D 7091 : 2005 | Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals |
| ASTM D 2197 : 2016 | Standard Test Method for Adhesion of Organic Coatings by Scrape Adhesion |
| ASTM D 4138 : 2007 : REV A : R2017 | Standard Practices for Measurement of Dry Film Thickness of Protective Coating Systems by Destructive, Cross-Sectioning Means |
| ASTM D 7234 : 2021 | Standard Test Method for Pull-Off Adhesion Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers |
| ASTM D 3359 : 2008 | Standard Test Methods for Measuring Adhesion by Tape Test |
| ASTM D 4541 : 1995 : EDT 1 | Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers |
| ASTM D 4138 : 2007 | Standard Practices for Measurement of Dry Film Thickness of Protective Coating Systems by Destructive, Cross-Sectioning Means |
| ASTM D 3359 : 2017 | Standard Test Methods for Rating Adhesion by Tape Test |
| ASTM D 2197 : 2016 : R2022 | Standard Test Method for Adhesion of Organic Coatings by Scrape Adhesion |
| ASTM D 6132 : 2004 | Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Applied Organic Coatings Using an Ultrasonic Gage |
| ASTM D 4138 : 2007 : REV A | Standard Practices for Measurement of Dry Film Thickness of Protective Coating Systems by Destructive, Cross-Sectioning Means |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.