Standard Specification for Polymer Concrete Pipe

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

07-21-2022

Publisher

American Society for Testing and Materials

1.1This specification covers polymer concrete pipe, 6 in. (150 mm) through 144 in. (3 660 mm), intended for use in gravity-flow systems for conveying sanitary sewage, storm water, and industrial wastes.

1.2Although this specification is suited primarily for pipe to be installed by direct burial and pipe jacking, it may be used to the extent applicable for other installations such as sliplining and rehabilitation of existing pipelines.

Note 1:Unlike reinforced thermosetting resin pipes, polymer concrete pipe is designed and installed using rigid pipe design theory and practices.

1.3The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

1.4The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

Note 2:There is no known ISO equivalent to this standard.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee	D 20
DocumentType	Standard
Pages	7
PublisherName	American Society for Testing and Materials
Status	Current
Supersedes	ASTM D 6783 : 2005 : REV A : R2017

ASTM D 883 : 2023	Standard Terminology Relating to Plastics
ASTM C 117 : 2017	Standard Test Method for Materials Finer than 75-μm (No. 200) Sieve in Mineral Aggregates by Washing
ASTM C 33/C33M : 2023	Standard Specification for Concrete Aggregates
ASTM F 412 : 2021	Standard Terminology Relating to Plastic Piping Systems
ASTM D 883 : 2024	Standard Terminology Relating to Plastics
ASTM C 33/C33M : 2018	Standard Specification for Concrete Aggregates
ASTM D 883 : 2022	Standard Terminology Relating to Plastics
ASTM D 883 : 2020 : REV B	Standard Terminology Relating to Plastics
ASTM D 3681 : 2018	Standard Test Method for Chemical Resistance of “Fiberglass” (Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a Deflected Condition
ASTM A 276/A276M : 2024 : REV A	Standard Specification for Stainless Steel Bars and Shapes
ASTM A 276/A276M : 2024	Standard Specification for Stainless Steel Bars and Shapes
ASTM C 136/C136M : 2014	Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates
ASTM A 276/A276M : 2017	Standard Specification for Stainless Steel Bars and Shapes
ASTM D 3681 : 2023	Standard Test Method for Chemical Resistance of “Fiberglass” (Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a Deflected Condition
ASTM C 117 : 2023	Standard Test Method for Materials Finer than 75-μm (No. 200) Sieve in Mineral Aggregates by Washing
ASTM D 1600 : 2018	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
ASTM A 276/A276M : 2023	Standard Specification for Stainless Steel Bars and Shapes
ASTM F 412 : 2023	Standard Terminology Relating to Plastic Piping Systems
ASTM C 579 : 2023	Standard Test Methods for Compressive Strength of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes
ASTM C 579 : 2018	Standard Test Methods for Compressive Strength of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes